Effect of heat treatments on microstructure and properties of CuCrZr produced by laser-powder bed fusion

2019 ◽  
Vol 744 ◽  
pp. 215-223 ◽  
Author(s):  
Christopher Wallis ◽  
Bruno Buchmayr
Keyword(s):  
Heat Treatments ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Powder Bed ◽  
Microstructure And Properties

scholarly journals Optimization of the Post-Process Heat Treatment of Inconel 718 Superalloy Fabricated by Laser Powder Bed Fusion Process

Metals ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 144
Author(s):  
Eslam M. Fayed ◽  
Mohammad Saadati ◽  
Davood Shahriari ◽  
Vladimir Brailovski ◽  
Mohammad Jahazi ◽  
...  
Keyword(s):  
Inconel 718 ◽  
Mechanical Performance ◽  
Solution Treatment ◽  
Heat Treatments ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Homogenization Treatment ◽  
Powder Bed ◽  
Post Process ◽  
High Fraction

In the present study, multi-objective optimization is employed to develop the optimum heat treatments that can achieve both high-mechanical performance and non-distinctive crystallographic texture of 3D printed Inconel 718 (IN718) fabricated by laser powder bed fusion (LPBF). Heat treatments including homogenization at different soaking times (2, 2.5, 3, 3.5 and 4 h) at 1080 °C, followed by a 1 h solution treatment at 980 °C and the standard aging have been employed. 2.5 h is found to be the homogenization treatment threshold after which there is a depletion of hardening precipitate constituents (Nb and Ti) from the γ-matrix. However, a significant number of columnar grains with a high fraction (37.8%) of low-angle grain boundaries (LAGBs) have still been retained after the 2.5 h homogenization treatment. After a 4 h homogenization treatment, a fully recrystallized IN718 with a high fraction of annealing twins (87.1%) is obtained. 2.5 and 4 h homogenization treatments result in tensile properties exceeding those of the wrought IN718 at both RT and 650 °C. However, considering the texture requirements, it is found that the 4 h homogenization treatment offers the optimum treatment, which can be used to produce IN718 components offering a balanced combination of high mechanical properties and adequate microstructural isotropy.

Effects of tantalum addition on microstructure and properties of titanium alloy fabricated by laser powder bed fusion

2021 ◽  
Vol 28 (4) ◽  
pp. 1111-1128
Author(s):  
Li-bo Zhou ◽  
Jing-guo Shu ◽  
Jin-shan Sun ◽  
Jian Chen ◽  
Jian-jun He ◽  
...  
Keyword(s):  
Titanium Alloy ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Powder Bed ◽  
Microstructure And Properties

scholarly journals Microstructure and Residual Stress Evolution of Laser Powder Bed Fused Inconel 718 under Heat Treatments

2020 ◽  
Author(s):  
Giulio Marchese ◽  
Eleonora Atzeni ◽  
Alessandro Salmi ◽  
Sara Biamino
Keyword(s):  
Residual Stresses ◽  
Inconel 718 ◽  
Heat Treatments ◽  
Powder Bed Fusion ◽  
Stress Evolution ◽  
Laser Powder Bed Fusion ◽  
Powder Bed ◽  
Melt Pool ◽  
Sintering Mechanisms ◽  
Dendritic Structures

AbstractThe current work aimed to study the influence of various heat treatments on the microstructure, hardness, and residual stresses of Inconel 718 processed by laser powder bed fusion process. The reduction in residual stresses is crucial to avoid the deformation of the component during its removal from the building platform. Among the different heat treatments, 800 °C kept almost unaltered the original microstructure, reducing the residual stresses. Heat treatments at 900, 980, and 1065 °C gradually triggered the melt pool and dendritic structures dissolution, drastically reducing the residual stresses. Heat treatments at 900 and 980 °C involved the formation of δ phases, whereas 1065 °C generated carbides. These heat treatments were also performed on components with narrow internal channels revealing that heat treatments up to 900 °C did not trigger sintering mechanisms allowing to remove the powder from the inner channels.

scholarly journals Short Heat Treatments for the F357 Aluminum Alloy Processed by Laser Powder Bed Fusion

Materials ◽  
2021 ◽  
Vol 14 (20) ◽  
pp. 6157
Author(s):  
Matteo Vanzetti ◽  
Enrico Virgillito ◽  
Alberta Aversa ◽  
Diego Manfredi ◽  
Federica Bondioli ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Precipitation Hardening ◽  
Solution Treatment ◽  
Heat Treatments ◽  
Point Of View ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Powder Bed ◽  
Heat Treated ◽  
Direct Aging

Conventionally processed precipitation hardening aluminum alloys are generally treated with T6 heat treatments which are time-consuming and generally optimized for conventionally processed microstructures. Alternatively, parts produced by laser powder bed fusion (L-PBF) are characterized by unique microstructures made of very fine and metastable phases. These peculiar features require specifically optimized heat treatments. This work evaluates the effects of a short T6 heat treatment on L-PBF AlSi7Mg samples. The samples underwent a solution step of 15 min at 540 °C followed by water quenching and subsequently by an artificial aging at 170 °C for 2–8 h. The heat treated samples were characterized from a microstructural and mechanical point of view and compared with both as-built and direct aging (DA) treated samples. The results show that a 15 min solution treatment at 540 °C allows the dissolution of the very fine phases obtained during the L-PBF process; the subsequent heat treatment at 170 °C for 6 h makes it possible to obtain slightly lower tensile properties compared to those of the standard T6. With respect to the DA samples, higher elongation was achieved. These results show that this heat treatment can be of great benefit for the industry.

Sign in / Sign up

Export Citation Format

Share Document