Composition and structure characterization of aluminum after laser ablation

2006 ◽  
Vol 135 (2) ◽  
pp. 108-112 ◽  
Author(s):  
I. Balchev ◽  
N. Minkovski ◽  
Ts. Marinova ◽  
M. Shipochka ◽  
N. Sabotinov
1990 ◽  
Vol 187 ◽  
Author(s):  
Dongliang Lin ◽  
Bewda Yan ◽  
Weili Yu

AbstractWNx film is one of the most promising materials for self-aligned GaAs NASFET because of its low electrical resistivity and high Schottky Barrier Height at the WNx /GaAs contact.In this paper, the effect of the sputtering conditions and the annealing environment on the chemical composition and structure of the WNx films deposited on Si and GaAs by RF reactive sputtering are studied.The results show that with the increase of the partial pressure ratio of nitrogen gas or decrease of the working pressure, deposition rate of WNx film decreases, whereas the atomic percentage of N in the deposited film increases before approaching saturation. The WNx films formed at high working pressure (≈5 × 10−2 torr) consist of W, WN or W2N phases depending on the nitrogen partial pressure ratio. Whereas the films formed at low working pressure (≈ 3 × 10−3 torr) are usually amorphous. Annealing in a flowing N2 gas causes the crystallization of the amorphous films, which mainly consist of W+W2N. There is no change for the crystalline films. However, annealing in H2 gas causes severe loss of nitrogen of the film, the film becoming single W phase eventually.


2018 ◽  
Vol 1027 ◽  
pp. 012002
Author(s):  
Ali Aqeel Salim ◽  
Noriah Bidin ◽  
Hazri Bakhtiar ◽  
Sib Krishna Ghoshal ◽  
Mohammed Al Azawi ◽  
...  

Author(s):  
X. Zhang ◽  
Y. Pan ◽  
T.T. Meek

Industrial microwave heating technology has emerged as a new ceramic processing technique. The unique advantages of fast sintering, high density, and improved materials properties makes it superior in certain respects to other processing methods. This work presents the structure characterization of a microwave sintered ceramic matrix composite.Commercial α-alumina powder A-16 (Alcoa) is chosen as the matrix material, β-silicon carbide whiskers (Third Millennium Technologies, Inc.) are used as the reinforcing element. The green samples consisted of 90 vol% Al2O3 powder and 10 vol% ultrasonically-dispersed SiC whiskers. The powder mixture is blended together, and then uniaxially pressed into a cylindrical pellet under a pressure of 230 MPa, which yields a 52% green density. The sintering experiments are carried out using an industry microwave system (Gober, Model S6F) which generates microwave radiation at 2.45 GHz with a maximum output power of 6 kW. The composites are sintered at two different temperatures (1550°C and 1650°C) with various isothermal processing time intervals ranging from 10 to 20 min.


1996 ◽  
Vol 451 ◽  
Author(s):  
S. D. Leith ◽  
D. T. Schwartz

ABSTRACTDescribed are results showing that an oscillating flow-field can induce spatially periodic composition variations in electrodeposited NiFe films. Flow-induced NiFe composition modulated alloys (CMA's) were deposited on the disk of a rotating disk electrode by oscillating the disk rotation rate during galvanostatic plating. Deposit composition and structure were investigated using potentiostatic stripping voltammetry and scanning probe microscopy. Results illustrate a linear relationship between the composition modulation wavelength and the flow oscillation period. CMA's with wavelengths less than 10 nm can be fabricated when plating with a disk rotation rate oscillation period less than 3 seconds.


Author(s):  
Nancy Van Suetendael ◽  
Kristie Powell ◽  
Susan Earles ◽  
Mary Helen McCay ◽  
Ivica Kostanic
Keyword(s):  

Author(s):  
P. Schwindenhammer ◽  
H. Murray ◽  
P. Descamps ◽  
P. Poirier

Abstract Decapsulation of complex semiconductor packages for failure analysis is enhanced by laser ablation. If lasers are potentially dangerous for Integrated Circuits (IC) surface they also generate a thermal elevation of the package during the ablation process. During measurement of this temperature it was observed another and unexpected electrical phenomenon in the IC induced by laser. It is demonstrated that this new phenomenon is not thermally induced and occurs under certain ablation conditions.


Sign in / Sign up

Export Citation Format

Share Document