The effect of primary and secondary flows on the homogenization process in a vertical bladed mixer

2021 ◽  
Author(s):  
J. Havlica ◽  
M. Kozakovic ◽  
D. Kramolis ◽  
T. Travnickova ◽  
M. Kohout
Keyword(s):  
Secondary Flows ◽  
Homogenization Process

MODELING OF THE INFLUENCE OF THERMIC TREATMENT UPON THE MECHANICAL PROPERTIES OF ALUMINUM-TIN ALLOYS

2015 ◽  
Vol 9 (2) ◽  
pp. 2431-2439
Author(s):  
Saad El Madani ◽  
S. ELHAMZI ◽  
J. KATTEN ◽  
A. IBNLFASSI
Keyword(s):  
Mechanical Properties ◽  
Solidification Process ◽  
Tin Alloys ◽  
Homogenization Process ◽  
Fundamental Reason ◽  
Segregation Phenomenon ◽  
Cooling Velocity

In order to master and improve the quality and properties of the final products, the major industrial challenge lies in the possibility of controlling the morphology, size of microstructures that reside within the molded pieces, as well as their defects; this is the fundamental reason according to which we are more and more interested in mastering the growth and germination of such alloys, as well as the developing structures, at the time of solidification process. The modeling reveals as a valuable aid in the mastery of the formation of such heterogeneousness: segregation cells that are incompatible with industrial requirements. The whole work focuses upon the modeling of the segregation phenomenon of the four hypoeutectic alloys, Al1%Sn, Al2%Sn, Al3%Sn and Al4%Sn, as well as the tin effect upon certain mechanical properties of aluminum. Usually, the microstructure and mechanical  behavior of such alloys as Al-Sn are directly influenced by some parameters such as composition, cooling velocity and homogenization process.

MODELISATION DE L'INFLUENCE DU TRAITEMENT THERMIQUE SUR LES PROPRIETES MECANIQUES DES ALLIAGES ALUMINIUM-CUIVRE (Al-Cu)

2015 ◽  
Vol 10 (2) ◽  
pp. 2753-2761
Author(s):  
Saad El Madani ◽  
S. ELHAMZI ◽  
A. IBNLFASSI ◽  
L. ZERROUK ◽  
O. BEN LENDA ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Mechanical Behavior ◽  
Solidification Process ◽  
Traitement Thermique ◽  
Homogenization Process ◽  
Fundamental Reason ◽  
Segregation Phenomenon ◽  
Proprietes Mecaniques ◽  
Cooling Velocity ◽  
Copper Effect

In order to master and improve the quality and properties of the final products, the major industrial challenge lies in the possibility of controlling the morphology, size of microstructures that reside within the molded pieces, as well as their defects; this is the fundamental reason according to which we are more and more interested in mastering the growth and germination of such alloys, as well as the developing structures, at the time of solidification process. The modeling reveals as a valuable aid in the mastery of the formation of such heterogeneousness: segregation cells that are incompatible with industrial requirements.   The whole work focuses upon the modeling of the segregation phenomenon of the four hypoeutectic alloys, Al1%Cu, Al2%Cu, Al3%Cu et Al4%Cu, as well as the copper effect upon certain mechanical properties of aluminum. Usually, the microstructure and mechanical behavior of such alloys as Al-Cu are directly influenced by some parameters such as composition, cooling velocity and homogenization process.

The Influence of Blade Wakes on the Performance of Interturbine Diffusers

1996 ◽  
Vol 118 (2) ◽  
pp. 347-352 ◽  
Author(s):  
R. G. Dominy ◽  
D. A. Kirkham
Keyword(s):  
Performance Modeling ◽  
Three Dimensional ◽  
Secondary Flows ◽  
Two Dimensional ◽  
Correct Performance ◽  
Analysis Methods ◽  
Flow Factor ◽  
The Mean ◽  
Lp Turbine

Interturbine diffusers provide continuity between HP and LP turbines while diffusing the flow upstream of the LP turbine. Increasing the mean turbine diameter offers the potential advantage of reducing the flow factor in the following stages, leading to increased efficiency. The flows associated with these interturbine diffusers differ from those in simple annular diffusers both as a consequence of their high-curvature S-shaped geometry and of the presence of wakes created by the upstream turbine. It is shown that even the simplest two-dimensional wakes result in significantly modified flows through such ducts. These introduce strong secondary flows demonstrating that fully three-dimensional, viscous analysis methods are essential for correct performance modeling.

scholarly journals Investigation of Separation Phenomena in a Radial Pump at Reduced Flow Rate by Large-Eddy Simulation

2016 ◽  
Vol 138 (12) ◽  
Author(s):  
Antonio Posa ◽  
Antonio Lippolis ◽  
Elias Balaras
Keyword(s):  
Reverse Flow ◽  
Leading Edge ◽  
Suction Side ◽  
Secondary Flows ◽  
Vaned Diffuser ◽  
Flow Rates ◽  
Turbulent Statistics ◽  
Large Eddy ◽  
Radial Pump ◽  
Reduced Flow

Turbopumps operating at reduced flow rates experience significant separation and backflow phenomena. Although Reynolds-Averaged Navier–Stokes (RANS) approaches proved to be usually able to capture the main flow features at design working conditions, previous numerical studies in the literature verified that eddy-resolving techniques are required in order to simulate the strong secondary flows generated at reduced loads. Here, highly resolved large-eddy simulations (LES) of a radial pump with a vaned diffuser are reported. The results are compared to particle image velocimetry (PIV) experiments in the literature. The main focus of the present work is to investigate the separation and backflow phenomena occurring at reduced flow rates. Our results indicate that the effect of these phenomena extends up to the impeller inflow: they involve the outer radii of the impeller vanes, influencing significantly the turbulent statistics of the flow. Also in the diffuser vanes, a strong spanwise evolution of the flow has been observed at the reduced load, with reverse flow, located mainly on the shroud side and on the suction side (SS) of the stationary channels, especially near the leading edge of the diffuser blades.

scholarly journals A Review of Numerical Simulations of Secondary Flows in River Bends

Water ◽  
2021 ◽  
Vol 13 (7) ◽  
pp. 884
Author(s):  
Rawaa Shaheed ◽  
Abdolmajid Mohammadian ◽  
Xiaohui Yan
Keyword(s):  
Numerical Modeling ◽  
Numerical Simulations ◽  
Secondary Flow ◽  
Cross Section ◽  
Turbulence Models ◽  
Main Flow ◽  
Secondary Flows ◽  
River Bends ◽  
River Cross Section ◽  
River Bend

River bends are one of the common elements in most natural rivers, and secondary flow is one of the most important flow features in the bends. The secondary flow is perpendicular to the main flow and has a helical path moving towards the outer bank at the upper part of the river cross-section, and towards the inner bank at the lower part of the river cross-section. The secondary flow causes a redistribution in the main flow. Accordingly, this redistribution and sediment transport by the secondary flow may lead to the formation of a typical pattern of river bend profile. It is important to study and understand the flow pattern in order to predict the profile and the position of the bend in the river. However, there are a lack of comprehensive reviews on the advances in numerical modeling of bend secondary flow in the literature. Therefore, this study comprehensively reviews the fundamentals of secondary flow, the governing equations and boundary conditions for numerical simulations, and previous numerical studies on river bend flows. Most importantly, it reviews various numerical simulation strategies and performance of various turbulence models in simulating the flow in river bends and concludes that the main problem is finding the appropriate model for each case of turbulent flow. The present review summarizes the recent advances in numerical modeling of secondary flow and points out the key challenges, which can provide useful information for future studies.

scholarly journals Focusing of Particles in a Microchannel with Laser Engraved Groove Arrays

Biosensors ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 263
Author(s):  
Tianlong Zhang ◽  
Yigang Shen ◽  
Ryota Kiya ◽  
Dian Anggraini ◽  
Tao Tang ◽  
...  
Keyword(s):  
Open Space ◽  
Lateral Displacement ◽  
Reynolds Numbers ◽  
Secondary Flows ◽  
Particle Sedimentation ◽  
Nanoparticle Separation ◽  
Wide Range ◽  
Fs Laser ◽  
Channel Bottom ◽  
Myoblast Cells

Continuous microfluidic focusing of particles, both synthetic and biological, is significant for a wide range of applications in industry, biology and biomedicine. In this study, we demonstrate the focusing of particles in a microchannel embedded with glass grooves engraved by femtosecond pulse (fs) laser. Results showed that the laser-engraved microstructures were capable of directing polystyrene particles and mouse myoblast cells (C2C12) towards the center of the microchannel at low Reynolds numbers (Re < 1). Numerical simulation revealed that localized side-to-center secondary flows induced by grooves at the channel bottom play an essential role in particle lateral displacement. Additionally, the focusing performance proved to be dependent on the angle of grooves and the middle open space between the grooves based on both experiments and simulation. Particle sedimentation rate was found to critically influence the focusing of particles of different sizes. Taking advantage of the size-dependent particle lateral displacement, selective focusing of micrometer particles was demonstrated. This study systematically investigated continuous particle focusing in a groove-embedded microchannel. We expect that this device will be used for further applications, such as cell sensing and nanoparticle separation in biological and biomedical areas.

Sign in / Sign up

Export Citation Format

Share Document