Microstructure and high-temperature mechanical properties of near net shaped Ti−45Al−7Nb−0.3W alloy by hot isostatic pressing process

2020 ◽  
Vol 30 (11) ◽  
pp. 3006-3015
Author(s):  
Hui-zhong LI ◽  
Yi-xuan CHE ◽  
Xiao-peng LIANG ◽  
Hui TAO ◽  
Qiang ZHANG ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Hot Isostatic Pressing ◽  
Isostatic Pressing ◽  
High Temperature Mechanical Properties ◽  
Pressing Process

TEM Studies of Grain Boundary Films in Si3N4 Ceramics

1991 ◽  
Vol 49 ◽  
pp. 930-931
Author(s):  
H.-J. Kleebe ◽  
J.S. Vetrano ◽  
J. Bruley ◽  
M. Rühle
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Silicon Nitride ◽  
Hot Isostatic Pressing ◽  
Amorphous Film ◽  
Liquid Phase Sintering ◽  
Second Phase ◽  
High Temperature Mechanical Properties ◽  
Triple Points ◽  
Boundary Films

It is expected that silicon nitride based ceramics will be used as high-temperature structural components. Though much progress has been made in both processing techniques and microstructural control, the mechanical properties required have not yet been achieved. It is thought that the high-temperature mechanical properties of Si3N4 are limited largely by the secondary glassy phases present at triple points. These are due to various oxide additives used to promote liquid-phase sintering. Therefore, many attempts have been performed to crystallize these second phase glassy pockets in order to improve high temperature properties. In addition to the glassy or crystallized second phases at triple points a thin amorphous film exists at two-grain junctions. This thin film is found even in silicon nitride formed by hot isostatic pressing (HIPing) without additives. It has been proposed by Clarke that an amorphous film can exist at two-grain junctions with an equilibrium thickness.

scholarly journals Application research progress of hot isostatic pressing technology in nickel-based single crystal superalloy

2020 ◽  
Vol 155 ◽  
pp. 01012
Author(s):  
Jun Wang ◽  
Zhaojun Jiang
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Single Crystal ◽  
Hot Isostatic Pressing ◽  
Single Crystal Superalloy ◽  
Research Progress ◽  
Application Research ◽  
Isostatic Pressing ◽  
Increasing Demand ◽  
Pressing Technology

Since the introduction of hot isostatic pressing (HIP) technology, it has been widely used in powder metallurgy forming and improving the densification of castings. With the increasing demand for the performance of nickel-based single crystal superalloy, more and more scholars started research on the application of hot isostatic pressing in nickel-based single crystal superalloy. This article summarizes the current research progress in the application of hot isostatic pressing to the high temperature of nickel-based single crystals, explains the elimination effect of hot isostatic pressing on porosity and other pore defects in nickel-based single crystal superalloy, analyzes the pore healing mechanism, and the changes in mechanical properties such as tensile, endurance, and fatigue of the alloy after applying hot isostatic pressing are shown. Finally, the future development of China’s hot isostatic pressing technology is prospected.

Rapid synthesis of bulk Ti2AlC by self-propagating high temperature combustion synthesis with a pseudo–hot isostatic pressing process

2009 ◽  
Vol 24 (8) ◽  
pp. 2528-2535 ◽  
Author(s):  
Yuelei Bai ◽  
Xiaodong He ◽  
Yibin Li ◽  
Chuncheng Zhu ◽  
Sam Zhang
Keyword(s):  
High Temperature ◽  
Combustion Synthesis ◽  
Hot Isostatic Pressing ◽  
X Ray Diffraction ◽  
Phase Purity ◽  
X Ray ◽  
Isostatic Pressing ◽  
Pressing Process ◽  
Temperature Combustion ◽  
High Temperature Combustion

In this study, the dense polycrystalline Ti2AlC was synthesized by self-propagating high-temperature combustion synthesis with the pseudo–hot isostatic pressing process (SHS/PHIP). The resultant phase purity is highly dependent on the mol ratio of raw powders. The Ti2AlC was densified by applying pressure after the SHS reaction. The resultant sample mainly contains typical plate-like nonstoichiometric Ti2AlCx (x = 0.69) with grain size of ∼6 µm. The sample shows the Vickers hardness of 5.5 GPa, highest flexural strength of 431 MPa, compressive strength of 1033 MPa, and fracture toughness of 6.5 MPa·m1/2. No indentation cracks in Ti2AlCx were observed, indicative of a damage material nature. The reaction mechanism for the formation of SHS/PHIP-derived Ti2AlC is also discussed based on differential thermal analysis and x-ray diffraction results.

BERYLCO NICKEL ALLOY 440

Alloy Digest ◽  
1975 ◽  
Vol 24 (9) ◽  
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Nickel Alloy ◽  
High Strength ◽  
Heat Treating ◽  
Electronic Components ◽  
High Temperature Mechanical Properties ◽  
Temperature Performance ◽  
Solution Treated ◽  
Complex Shapes

Abstract BERYLCO NICKEL ALLOY 440 is an age-hardenable nickel-beryllium-titanium alloy that offers high strength, excellent spring properties outstanding formability, good high-temperature mechanical properties, and resistance to corrosion and fatigue. Complex shapes can be produced in the solution-treated (soft) condition and then aged to a minimum tensile strength of 215,500 psi. It is used for mechanical and electrical/electronic components in the temperature range -320 to 800 F. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fracture toughness. It also includes information on high temperature performance and corrosion resistance as well as forming, heat treating, machining, joining, and surface treatment. Filing Code: Ni-94. Producer or source: Kawecki Berylco Industries Inc.. Originally published September 1964, revised September 1975.

HASTELLOY ALLOY S

Alloy Digest ◽  
1973 ◽  
Vol 22 (1) ◽  
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Heat Treating ◽  
High Temperature Alloy ◽  
Excellent Thermal Stability ◽  
Cabot Corporation ◽  
High Temperature Mechanical Properties ◽  
Temperature Performance ◽  
Resistance To Oxidation ◽  
Nickel Base

Abstract HASTELLOY alloy S is a nickel-base high-temperature alloy having excellent thermal stability, good high-temperature mechanical properties and excellent resistance to oxidation up to 2000 F. This datasheet provides information on composition, physical properties, elasticity, and tensile properties as well as creep. It also includes information on high temperature performance and corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: Ni-184. Producer or source: Stellite Division, Cabot Corporation.

Sign in / Sign up

Export Citation Format

Share Document