scholarly journals Improvement of High Temperature Fatigue Properties of TiAl Alloys Fabricated by Electron Beam Melting Through Hot Isostatic Pressing Process

2020 ◽  
Vol 9 (4) ◽  
pp. 180-184
Author(s):  
Ken CHO ◽  
Hiroyuki YASUDA ◽  
Mitsuharu TODAI ◽  
Minoru UEDA ◽  
Masao TAKEYAMA ◽  
...  
Keyword(s):  
Electron Beam ◽  
High Temperature ◽  
Electron Beam Melting ◽  
Hot Isostatic Pressing ◽  
Fatigue Properties ◽  
Tial Alloys ◽  
Isostatic Pressing ◽  
High Temperature Fatigue ◽  
Pressing Process

scholarly journals Encapsulation of Electron Beam Melting Produced Alloy 718 to Reduce Surface Connected Defects by Hot Isostatic Pressing

Materials ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1226 ◽  
Author(s):  
Yunus Emre Zafer ◽  
Sneha Goel ◽  
Ashish Ganvir ◽  
Anton Jansson ◽  
Shrikant Joshi
Keyword(s):  
Electron Beam ◽  
Electron Beam Melting ◽  
Surface Defects ◽  
High Surface ◽  
Hot Isostatic Pressing ◽  
Coated Sample ◽  
Alloy 718 ◽  
Isostatic Pressing ◽  
Before And After ◽  
X Ray Computed

Defects in electron beam melting (EBM) manufactured Alloy 718 are inevitable to some extent, and are of concern as they can degrade mechanical properties of the material. Therefore, EBM-manufactured Alloy 718 is typically subjected to post-treatment to improve the properties of the as-built material. Although hot isostatic pressing (HIPing) is usually employed to close the defects, it is widely known that HIPing cannot close open-to-surface defects. Therefore, in this work, a hypothesis is formulated that if the surface of the EBM-manufactured specimen is suitably coated to encapsulate the EBM-manufactured specimen, then HIPing can be effective in healing such surface-connected defects. The EBM-manufactured Alloy 718 specimens were coated by high-velocity air fuel (HVAF) spraying using Alloy 718 powder prior to HIPing to evaluate the above approach. X-ray computed tomography (XCT) analysis of the defects in the same coated sample before and after HIPing showed that some of the defects connected to the EBM specimen surface were effectively encapsulated by the coating, as they were closed after HIPing. However, some of these surface-connected defects were retained. The reason for such remnant defects is attributed to the presence of interconnected pathways between the ambient and the original as-built surface of the EBM specimen, as the specimens were not coated on all sides. These pathways were also exaggerated by the high surface roughness of the EBM material and could have provided an additional path for argon infiltration, apart from the uncoated sides, thereby hindering complete densification of the specimen during HIPing.

scholarly journals Effect of Hot Isostatic Pressing on Microstructures and Mechanical Properties of Ti6Al4V Fabricated by Electron Beam Melting

Metals ◽  
2020 ◽  
Vol 10 (5) ◽  
pp. 593
Author(s):  
Changyong Liu ◽  
Zhuokeng Mai ◽  
Deng Yan ◽  
Mingguang Jiang ◽  
Yuhong Dai ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Grain Size ◽  
Electron Beam ◽  
Electron Beam Melting ◽  
Hot Isostatic Pressing ◽  
Phase Ratio ◽  
Lamellar Thickness ◽  
Isostatic Pressing ◽  
Β Phase

This study investigated the effects of hot isostatic pressing (HIP) on the microstructures and mechanical properties of Ti6Al4V fabricated by electron beam melting (EBM). The differences of surface morphologies, internal defects, relative density, microstructures, textures, mechanical properties and tensile fracture between the as-built and HIPed samples were observed using various characterization methods including optical metallography microscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM) and electron backscattered diffraction (EBSD) and tensile tests. It was found that the main effects of HIP on microstructures include—the increase of average grain size from 7.96 ± 1.21 μm to 11.34 ± 1.89 μm, the increase of α lamellar thickness from 0.71 ± 0.15 μm to 2.49 ± 1.29 μm and the increase of β phase ratio from 4.7% to 10.5% in terms of area fraction on the transversal section. The combinatorial effects including densification, increase of grain size, α lamellar thickness, β phase ratio, reduction of dislocation density and transformation of dislocation patterns contributed to the improvement of elongation and ductility of EBM-fabricated Ti6Al4V. Meanwhile, these effects also resulted in a slight reduction of the yield strength and UTS mainly due to the coarsening effect of HIP.

Microstructure and Fatigue Properties of TiAl with Unique Layered Microstructure Fabricated by Electron Beam Melting

2018 ◽  
Vol 941 ◽  
pp. 1597-1602
Author(s):  
Ken Cho ◽  
Ryota Kobayashi ◽  
Takuma Fukuoka ◽  
Jong Yeong Oh ◽  
Hiroyuki Y. Yasuda ◽  
...  
Keyword(s):  
Electron Beam ◽  
Fatigue Life ◽  
Fatigue Strength ◽  
Crack Propagation ◽  
Electron Beam Melting ◽  
Low Cycle Fatigue ◽  
Hot Isostatic Pressing ◽  
Fatigue Properties ◽  
Cycle Fatigue ◽  
Cast Alloys

The effect of a unique layered microstructure consisting of duplex-like region and equiaxed γ grains (γ bands) on the fatigue properties of Ti-48Al-2Cr-2Nb alloy bars fabricated by electron beam melting (EBM) at an angle (θ) of 90° between the building direction and cylinder (loading) axis was investigated focusing on the layered microstructure and test temperature. We found the room temperature (RT) fatigue strength of the alloy bars fabricated at θ = 90° is higher than that of the bars fabricated at θ = 0°. Moreover, it is comparable to that of the cast alloys with hot isostatic pressing (HIP) treatment in low-cycle fatigue life region, even without HIP treatment. The high fatigue strength of the bars at RT is attributed to the γ band, which acts as a resistance for crack propagation directed perpendicular to the γ band. On the other hand, the fatigue strength of the bars at θ = 90° is lower than that of the bars at θ = 0° in low-cycle fatigue life region at 1023 K. This is because the γ bands dose not act as a resistance for crack propagation at 1023 K. Although the bars at θ = 90° exhibits low fatigue strength in the region at 1023 K, that value is comparable to that of HIP-treated cast alloys due to the fine grain size, which is one of the features for the alloys fabricated by the EBM.

Effect of HIPping (Hot Isostatic Pressing) on electron beam melting Ti6Al4V parts after machining

2016 ◽  
Author(s):  
Adrien Dolimont ◽  
Sebastien Michotte ◽  
Edouard Rivière-Lorphèvre ◽  
François Ducobu ◽  
Charlotte de Formanoir ◽  
...  
Keyword(s):  
Electron Beam ◽  
Electron Beam Melting ◽  
Hot Isostatic Pressing ◽  
Isostatic Pressing

Rapid synthesis of bulk Ti2AlC by self-propagating high temperature combustion synthesis with a pseudo–hot isostatic pressing process

2009 ◽  
Vol 24 (8) ◽  
pp. 2528-2535 ◽  
Author(s):  
Yuelei Bai ◽  
Xiaodong He ◽  
Yibin Li ◽  
Chuncheng Zhu ◽  
Sam Zhang
Keyword(s):  
High Temperature ◽  
Combustion Synthesis ◽  
Hot Isostatic Pressing ◽  
X Ray Diffraction ◽  
Phase Purity ◽  
X Ray ◽  
Isostatic Pressing ◽  
Pressing Process ◽  
Temperature Combustion ◽  
High Temperature Combustion

In this study, the dense polycrystalline Ti2AlC was synthesized by self-propagating high-temperature combustion synthesis with the pseudo–hot isostatic pressing process (SHS/PHIP). The resultant phase purity is highly dependent on the mol ratio of raw powders. The Ti2AlC was densified by applying pressure after the SHS reaction. The resultant sample mainly contains typical plate-like nonstoichiometric Ti2AlCx (x = 0.69) with grain size of ∼6 µm. The sample shows the Vickers hardness of 5.5 GPa, highest flexural strength of 431 MPa, compressive strength of 1033 MPa, and fracture toughness of 6.5 MPa·m1/2. No indentation cracks in Ti2AlCx were observed, indicative of a damage material nature. The reaction mechanism for the formation of SHS/PHIP-derived Ti2AlC is also discussed based on differential thermal analysis and x-ray diffraction results.

Sign in / Sign up

Export Citation Format

Share Document