scholarly journals Pressure dependence of the band-gap energy and the conduction-band mass for an n-type InGaAs/GaAs strained single-quantum well

1998 ◽  
Vol 2 (1-4) ◽  
pp. 146-150 ◽  
Author(s):  
E.D. Jones ◽  
S.W. Tozer ◽  
T. Schmiedel
2007 ◽  
Vol 1012 ◽  
Author(s):  
Shimpei Teshima ◽  
Hirotake Kashiwabara ◽  
Keimei Masamoto ◽  
Kazuya Kikunaga ◽  
Kazunori Takeshita ◽  
...  

AbstractDependence of band alignments at interfaces between CdS by chemical bath deposition and Cu(In1-xGax)Se2 by conventional 3-stage co-evaporation on Ga substitution ratio x from 0.2 to 1.0 has been systematically studied by means of photoemission spectroscopy (PES) and inverse photoemission spectroscopy (IPES). For the specimens of the In-rich CIGS, conduction band minimum (CBM) by CIGS was lower than that of CdS. Conduction band offset of them was positive about +0.3 ~ +0.4 eV. Almost flat conduction band alignment was realized at x = 0.4 ~ 0.5. On the other hand, at the interfaces over the Ga-rich CIGS, CBM of CIGS was higher than that of CdS, and CBO became negative. The present study reveals that the decrease of CBO with a rise of x presents over the wide rage of x, which results in the sign change of CBO around 0.4 ~ 0.45. In the Ga-rich interfaces, the minimum of band gap energy, which corresponded to energy spacing between CBM of CdS and valence band maximum of CIGS, was almost identical against the change of band gap energy of CIGS. Additionally, local accumulation of oxygen related impurities was observed at the Ga-rich samples, which might cause the local rise of band edges in central region of the interface.


2014 ◽  
Vol 608 ◽  
pp. 66-68 ◽  
Author(s):  
Chuan-Zhen Zhao ◽  
Tong Wei ◽  
Xiao-Dong Sun ◽  
Sha-Sha Wang ◽  
Ke-Qing Lu

2014 ◽  
Vol 116 (6) ◽  
pp. 063512 ◽  
Author(s):  
Chuan-Zhen Zhao ◽  
Tong Wei ◽  
Na-Na Li ◽  
Sha-Sha Wang ◽  
Ke-Qing Lu

2018 ◽  
Vol 1 (02) ◽  
pp. 54-59
Author(s):  
Agus Ismangil ◽  
Teguh Puja Negara

One of the studies that recently attracted the attention of physicists is research on ferroelectric material because this material is very promising for the development of new generation devices in connection with the unique properties it has. Ferroelectric materials, especially those based on a mixture of lithium tantalite (LiTaO3), are expected to be applied to the infrared sensor. Lithium tantalate (LiTaO3) is a ferroelectric material that is unique in terms of pyroelectric and piezoelectric properties that are integrated with good mechanical and chemical stability. Therefore LiTaO3 is often used for several applications such as electro-optical modulators and pyroelectric detectors. LiTaO3 is a non-hygroscopic crystal, colorless, soluble in water, has a high transmission rate and does not easily damage its optical properties. LiTaO3 is a material that has a high dielectric constant and a high load storage capacity. This research has succeeded in determining the band gap energy of the LiTaO3 film in the rubidium chamber obtained in the range of values 2.02-2.98 eV as shown in figure 4. The LiTaO3 film after the annealing process at a temperature of 650 oC, has the highest band gap energy of 2.98 eV. Large energy is needed on the electrons to be excited from the valence band to the conduction band. Whereas in the LiTaO3 film after an annealing process of 800 oC, the band gap energy obtained is 2.02 eV. This makes it easier for electrons to be excited from the valence band to the conduction band because the energy needed is not too large.


2016 ◽  
Vol 494 ◽  
pp. 71-74 ◽  
Author(s):  
Chuan-Zhen Zhao ◽  
Tong Wei ◽  
Xiao-Dong Sun ◽  
Sha-Sha Wang ◽  
Ke-Qing Lu

2004 ◽  
Vol 84 (1) ◽  
pp. 67-69 ◽  
Author(s):  
W. Shan ◽  
W. Walukiewicz ◽  
J. W. Ager ◽  
K. M. Yu ◽  
J. Wu ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document