Effects of pylon geometry on mixing enhancement in a scramjet pylon-cavity flameholder

2020 ◽  
Vol 124 (1278) ◽  
pp. 1262-1280
Author(s):  
A. Oamjee ◽  
R. Sadanandan
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Supersonic Combustion ◽  
Total Pressure Loss ◽  
Absolute Pressure ◽  
Mixing Efficiency ◽  
Mixing Enhancement ◽  
Scramjet Combustor ◽  
Fuel Jet ◽  
Jet Penetration

ABSTRACTNumerical investigation of the effect of pylon geometry within a pylon-cavity aided Supersonic Combustion Ramjet (SCRAMJET) combustor on mixing enhancement, flame-holding capability, fuel jet penetration and total pressure loss are conducted in the current study. RANS equations for compressed real gas are solved by coupled, implicit, second-order upwind solver. A two-equation SST model is used for turbulence modelling. Validation of the computational model is performed with the help of experimental data collected using surface pressure taps, Schlieren flow visualisation and particle image velocimetry (PIV). The study uses four distinct pylon geometry cases, which include the baseline geometry. Sonic injection of hydrogen fuel through a 1mm diameter hole at 2mm downstream of the pylon rear face along the axis of the test section floor is performed for every case. A crossflow of Mach number 2.2 at four bar absolute pressure and standard atmospheric temperature is maintained. A comparative study of mixing efficiency, total pressure loss, fuel jet penetration and fuel plume area fraction for the different cases evaluate the mixing performance. The simulations show that the Pylon 2 case gives a significant improvement in the performance parameters compared to the other geometries. It is observed that mixing efficiency and fuel jet penetration capability of the system are highly dependent on the streamwise vortex within the flameholder.

scholarly journals A LES Study on Passive Mixing in Supersonic Shear Layer Flows Considering Effects of Baffle Configuration

2014 ◽  
Vol 6 ◽  
pp. 836146 ◽  
Author(s):  
Ren Zhao-Xin ◽  
Wang Bing
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Large Scale ◽  
Mixing Layer ◽  
Total Pressure Loss ◽  
Mixing Efficiency ◽  
Mixing Enhancement ◽  
Supersonic Mixing ◽  
Passive Mixing ◽  
Supersonic Mixing Layer

Under the background of dual combustor ramjet (DCR), a numerical investigation of supersonic mixing layer was launched, focused on the mixing enhancement method of applying baffles with different geometric configurations. Large eddy simulation with high order schemes, containing a fifth-order hybrid WENO compact scheme for the convective flux and sixth-order compact one for the viscous flux, was utilized to numerically study the development of the supersonic mixing layer. The supersonic cavity flow was simulated and the cavity configuration could influence the mixing characteristics, since the impingement process of large scale structures formed inside the cavity could raise the vorticity and promote the mixing. The effect of baffle's configurations on the mixing process was analyzed by comparing the flow properties, mixing efficiency, and total pressure loss. The baffle could induce large scale vortexes, promote the mixing layer to lose its stability easily, and then lead to the mixing efficiency enhancement. However, the baffle could increase the total pressure loss. The present investigation could provide guidance for applying new passive mixing enhancement methods for the supersonic mixing.

Numerical investigations on the hydrogen jet pressure variations in a strut based scramjet combustor

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Jeyakumar Suppandipillai ◽  
Jayaraman Kandasamy ◽  
R. Sivakumar ◽  
Mehmet Karaca ◽  
Karthik K.
Keyword(s):  
Shock Wave ◽  
Supersonic Flow ◽  
Pressure Loss ◽  
Total Pressure ◽  
Injection Pressure ◽  
Total Pressure Loss ◽  
Normal Shock ◽  
Content Type ◽  
Normal Shock Wave ◽  
Scramjet Combustor

Purpose This paper aims to study the influences of hydrogen jet pressure on flow features of a strut-based injector in a scramjet combustor under-reacting cases are numerically investigated in this study. Design/methodology/approach The numerical analysis is carried out using Reynolds Averaged Navier Stokes (RANS) equations with the Shear Stress Transport k-ω turbulence model in contention to comprehend the flow physics during scramjet combustion. The three major parameters such as the shock wave pattern, wall pressures and static temperature across the combustor are validated with the reported experiments. The results comply with the range, indicating the adopted simulation method can be extended for other investigations as well. The supersonic flow characteristics are determined based on the flow properties, combustion efficiency and total pressure loss. Findings The results revealed that the augmentation of hydrogen jet pressure via variation in flame features increases the static pressure in the vicinity of the strut and destabilize the normal shock wave position. Indeed, the pressure of the mainstream flow drives the shock wave toward the upstream direction. The study perceived that once the hydrogen jet pressure is reached 4 bar, the incoming flow attains a subsonic state due to the movement of normal shock wave ahead of the strut. It is noticed that the increase in hydrogen jet pressure in the supersonic flow field improves the jet penetration rate in the lateral direction of the flow and also increases the total pressure loss as compared with the baseline injection pressure condition. Practical implications The outcome of this research provides the influence of fuel injection pressure variations in the supersonic combustion phenomenon of hypersonic vehicles. Originality/value This paper substantiates the effect of increasing hydrogen jet pressure in the reacting supersonic airstream on the performance of a scramjet combustor.

Numerical Research on the Mixing Mechanism of Lobed Mixer With New De-Swirling Structure

2016 ◽  
Author(s):  
Zhijun Lei ◽  
Jianbo Gong ◽  
Yanfeng Zhang ◽  
Shangmei Su ◽  
Chunyan Hu
Keyword(s):  
Numerical Simulation ◽  
Pressure Loss ◽  
Total Pressure ◽  
Recirculation Zone ◽  
Swirling Flow ◽  
Separation Bubble ◽  
Total Pressure Loss ◽  
Mixing Efficiency ◽  
Flow Mixing ◽  
Inlet Swirl

A detailed numerical simulation is presented to investigate the new de-swirling methods and their effect on the mixing mechanisms of a turbofan mixer with 12 lobes. The numerical simulation employed a commercial solver, ANSYS CFX, using k-ω SST model. The core-to-bypass temperature ratio and pressure ratio were set to 2.59, and 0.97 respectively, giving the Mach number of 0.66 and bypass ratio of 2.65 at mixing nozzle outlet. The inlet swirl typically accelerates the jet-flow mixing by enhancing the vortices intensity and interaction, but leakage swirling flow can cause a three-dimensional separation bubble and the recirculation zone resulting in the dramatic increasing the total pressure loss and thrust loss. Removal of the leakage swirling flow between the lobes’ trough and centre-body was the key to limit the negative influence of inlet swirl. Two IGV design were investigated, DS1 and DS2. DS1 was installed at the upstream of the lobed mixer, could remove the negative effect of inlet swirl properly, but also inhibited the active role of the inlet swirl. The total pressure and thrust loss reduced by 0.31% and 3.8%, respectively, but the mixing efficiency also decreased by 1.72%. DS2, an integrated strut with the lobed mixer design, not only ensured the structure strength of the lobed mixer, but also reduced the length and weight of the exhaust system. This method suppressed the flow separation bubble on centre-body to some extent, and eliminated the recirculation zone downstream of the cenrebody, resulting in the total pressure loss decrease of 0.31% and thrust gain of 3.63%. On the other hand, the method DS2 also made full use of the inlet swirl to enhance the jet-flow mixing, resulting in the mixing efficiency increased 1.54% compared with that of the DS1 case. Under the off-design conditions with the incidence angle of ±10°, the aerodynamic performance of the DS2 cases didn’t changed too much such as the DS1 cases.

scholarly journals Investigations on the Influence of the In-Stream Pylon and Strut on the Performance of a Scramjet Combustor

2014 ◽  
Vol 2014 ◽  
pp. 1-10 ◽  
Author(s):  
Hao Ouyang ◽  
Weidong Liu ◽  
Mingbo Sun
Keyword(s):  
Mach Number ◽  
Pressure Loss ◽  
Total Pressure ◽  
Wall Pressure ◽  
Total Pressure Loss ◽  
Research Results ◽  
Scramjet Combustor ◽  
Total Temperature

The influence of the in-stream pylon and strut on the performance of scramjet combustor was experimentally and numerically investigated. The experiments were conducted with a direct-connect supersonic model combustor equipped with multiple cavities. The entrance parameter of combustor corresponds to scramjet flight Mach number 4.0 with a total temperature of 947 K. The research results show that, compared with the scramjet combustor without pylon and strut, the wall pressure and the thrust of the scramjet increase due to the improvement of mixing and combustion effect due to the pylon and strut. The total pressure loss caused by the strut is considerable whereas pylon influence is slight.

scholarly journals The Combustion Characteristics of Double Ramps in a Strut-Based Scramjet Combustor

Energies ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 831
Author(s):  
A. Antony Athithan ◽  
S. Jeyakumar ◽  
Norbert Sczygiol ◽  
Mariusz Urbanski ◽  
A. Hariharasudan
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Computational Study ◽  
Flame Temperature ◽  
Total Pressure Loss ◽  
Reacting Flow ◽  
Hydrogen Distribution ◽  
Spatial Direction ◽  
Shock Interactions ◽  
Scramjet Combustor

This paper focuses on the influence of ramp locations upstream of a strut-based scramjet combustor under reacting flow conditions that are numerically investigated. In contrast, a computational study is adopted using Reynolds Averaged Navier Stokes (RANS) equations with the Shear Stress Transport (SST) k-ω turbulence model. The numerical results of the Deutsches Zentrum für Luft- und Raumfahrt or German Aerospace Centre (DLR) scramjet model are validated with the reported experimental values that show compliance within the range, indicating that the adopted simulation method can be extended for other investigations as well. The performance of the ramps in the strut-based scramjet combustor is analyzed based on parameters such as wall pressures, combustion efficiency and total pressure loss at various axial locations of the combustor. From the numerical shadowgraph, more shock interactions are observed upstream of the strut injection region for the ramp cases, which decelerates the flow downstream, and additional shock reflections with less intensity are also noticed when compared with the DLR scramjet model. The shock reflection due to the ramps enhances the hydrogen distribution in the spatial direction. The ignition delay is noticed for ramp combustors due to the deceleration of flow compared to the baseline strut only scramjet combustor. However, a higher flame temperature is observed with the ramp combustor. Because more shock interactions arise from the ramps, a marginal increase in the total pressure loss is observed for ramp combustors when compared to the baseline model.

Experimental Study of Combustion on a Micro Gas Turbine Combustor

2008 ◽  
Author(s):  
Feng-Shan Wang ◽  
Wen-Jun Kong ◽  
Bao-Rui Wang
Keyword(s):  
Gas Turbine ◽  
Pressure Loss ◽  
Loss Factor ◽  
Total Pressure ◽  
Combustion Efficiency ◽  
Total Pressure Loss ◽  
Test Facility ◽  
Inlet Temperature ◽  
Micro Gas Turbine ◽  
Oil Fuel

A research program is in development in China as a demonstrator of combined cooling, heating and power system (CCHP). In this program, a micro gas turbine with net electrical output around 100kW is designed and developed. The combustor is designed for natural gas operation and oil fuel operation, respectively. In this paper, a prototype can combustor for the oil fuel was studied by the experiments. In this paper, the combustor was tested using the ambient pressure combustor test facility. The sensors were equipped to measure the combustion performance; the exhaust gas was sampled and analyzed by a gas analyzer device. From the tests and experiments, combustion efficiency, pattern factor at the exit, the surface temperature profile of the outer liner wall, the total pressure loss factor of the combustion chamber with and without burning, and the pollutants emission fraction at the combustor exit were obtained. It is also found that with increasing of the inlet temperature, the combustion efficiency and the total pressure loss factor increased, while the exit pattern factor coefficient reduced. The emissions of CO and unburned hydrogen carbon (UHC) significantly reduced, but the emission of NOx significantly increased.

Film Cooling and Aerodynamic Performance on Multi-Cavity Squealer Tip of a Turbine Blade

2021 ◽  
Author(s):  
Feng Li ◽  
Zhao Liu ◽  
Zhenping Feng
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
Pressure Loss ◽  
Total Pressure ◽  
Aerodynamic Performance ◽  
Total Pressure Loss ◽  
Cooling Performance ◽  
Pressure Loss Coefficient ◽  
Blade Tip ◽  
Total Pressure Loss Coefficient

Abstract The blade tip region of the shroud-less high-pressure gas turbine is exposed to an extremely operating condition with combined high temperature and high heat transfer coefficient. It is critical to design new tip structures and apply effective cooling method to protect the blade tip. Multi-cavity squealer tip has the potential to reduce the huge thermal loads and improve the aerodynamic performance of the blade tip region. In this paper, numerical simulations were performed to predict the aerothermal performance of the multi-cavity squealer tip in a heavy-duty gas turbine cascade. Different turbulence models were validated by comparing to the experimental data. It was found that results predicted by the shear-stress transport with the γ-Reθ transition model have the best precision. Then, the film cooling performance, the flow field in the tip gap and the leakage losses were presented with several different multi-cavity squealer tip structures, under various coolant to mainstream mass flow ratios (MFR) from 0.05% to 0.15%. The results show that the ribs in the multi-cavity squealer tip could change the flow structure in the tip gap for that they would block the coolant and the leakage flow. In this study, the case with one-cavity (1C) achieves the best film cooling performance under a lower MFR. However, the cases with multi-cavity (2C, 3C, 4C) show higher film cooling effectiveness under a higher MFR of 0.15%, which are 32.6%%, 34.2%% and 41.0% higher than that of the 1C case. For the aerodynamic performance, the case with single-cavity has the largest total pressure loss coefficient in all MFR studied, whereas the case with two-cavity obtains the smallest total pressure loss coefficient, which is 7.6% lower than that of the 1C case.

Conjugate Heat Transfer Characteristics of Double Wall Cooling With Gradient Diameter of Film and Impingement Holes

2021 ◽  
Author(s):  
Juan He ◽  
Qinghua Deng ◽  
Zhenping Feng
Keyword(s):  
Heat Transfer ◽  
Pressure Loss ◽  
Total Pressure ◽  
Flow Direction ◽  
Turbine Blades ◽  
Total Pressure Loss ◽  
Advanced Technique ◽  
Cooling Effectiveness ◽  
Uniform Pattern ◽  
Double Wall

Abstract Double wall cooling, consisting of internal impingement cooling and external film cooling, is believed to be the most advanced technique in modern turbine blades cooling. In this paper, to improve the uniformity of temperature distribution, a flat plate double wall cooling model with gradient diameter of film and impingement holes was proposed, and the heat transfer and flow characteristics were investigated by solving steady three-dimensional Reynolds-Averaged Navier-Stokes (RANS) equations with SST k-ω turbulence model. The influence of gradient diameter on overall cooling effectiveness and total pressure loss was studied by comparing with the uniform pattern at the blowing ratios ranging from 0.5 to 2. For gradient diameter of film hole patterns, results show that −10% film pattern always has the lowest film flow non-uniformity coefficient. The laterally averaged overall cooling effectiveness of uniform pattern lies between that of +10% and −10% film patterns, but the intersection of three patterns moves upstream from the middle of flow direction with the increase of blowing ratio. Therefore, the −10% film pattern exerts the highest area averaged cooling effectiveness, which is improved by up to 1.6% and 1% at BR = 0.5 and 1 respectively compared with a uniform pattern. However, at higher blowing ratios, the +10% film pattern maintains higher cooling effectiveness and lower total pressure loss. For gradient diameter of impingement hole patterns, the intersection of laterally averaged overall cooling effectiveness in three patterns is located near the middle of flow direction under all blowing ratios. The uniform pattern has the highest area averaged cooling effectiveness and the smallest non-uniform coefficient, but the −10% jet pattern has advantages of reducing pressure loss, especially in the laminated loss.

Sign in / Sign up

Export Citation Format

Share Document