On the behaviour of impinging zero-net-mass-flux jets

2016 ◽  
Vol 810 ◽  
pp. 25-59 ◽  
Author(s):  
Carlo Salvatore Greco ◽  
Gennaro Cardone ◽  
Julio Soria
Keyword(s):  
Flow Field ◽  
Vortex Ring ◽  
Strouhal Number ◽  
Mass Flux ◽  
Mean Flow ◽  
Turbulent Statistics ◽  
Image Velocimetry ◽  
The Mean ◽  
Zero Net Mass Flux ◽  
Plate Distance

This paper reports on an experimental study of the influence of the Strouhal number (0.011, 0.022 and 0.044) and orifice-to-plate distances (2, 4 and 6 orifice diameters) on the flow field of an impinging zero-net-mass-flux jet at a Reynolds number equal to 35 000. These jets are generated by a reciprocating piston that oscillates in a cavity behind a circular orifice. Instantaneous two-dimensional in-plane velocity fields are measured in a plane containing the orifice axis using multigrid/multipass cross-correlation digital particle image velocimetry. These measurements have been used to investigate the mean flow quantities and turbulent statistics of the impinging zero-net-mass-flux jets. In addition, the vortex ring behaviour is analysed via its trajectory and azimuthal vorticity as well as the saddle point excursion, the flow rate and entrainment. The behaviour of all these quantities depends on the Strouhal number and the orifice-to-plate distance because the former governs the presence and the relative importance of the vortex ring and the trailing jet on the flow field and the latter delimits the downstream evolution of these structures.

Capability Assessment of Five Different RANS-Based Turbulence Models to Simulate the Various Regions of Slot Turbulent Impingement Jet Flow

2017 ◽  
Author(s):  
Mahmoud Charmiyan ◽  
Ahmed-Reza Azimian ◽  
Ebrahim Shirani ◽  
Fethi Aloui
Keyword(s):  
Experimental Data ◽  
Turbulence Models ◽  
Jet Flows ◽  
Two Dimensional ◽  
Mean Flow ◽  
Impingement Jet ◽  
Image Velocimetry ◽  
The Mean ◽  
Bottom To Top ◽  
Plate Distance

In this paper, impingement of a turbulent rectangular flow to a fixed wall is investigated. The jet flows from bottom-to-top and the output jet Reynolds is 16000. The nozzle-to-plate distance is equal to 10 (H/e = 10). Five turbulence models, including k-ε, RNG k-ε, k-ω SST, RSM and v2f model have been used for two-dimensional numerical simulation of the turbulent flow. Because of the complexities of the impingement flow, such as curved streamlines, flow separation, normal strains and sudden deceleration in different areas, different turbulence models are proposed to simulate different regions of the flow. To investigate the capability of these turbulence models in simulating different regions of the impinging jet, the mean flow velocity field and turbulent kinetic energy are extracted and compared with the experimental data of a two-dimensional particle image velocimetry (PIV). The calculated error of these five turbulence models was presented for the various flow regions, while it have not been clearly investigated earlier. Results indicate the highest conformity of the v2f model with the experimental data at the jet centerline. However, this model does not predict well the flow at the shear layer and wall-jet areas. RSM Gibson and Lander model has the highest conformity with the experimental data in these regions.

Flow and Heat Transfer Analysis in a Single Row Narrow Impingement Channel: Comparison of PIV, LES, and RANS to Identify RANS Limitations

2017 ◽  
Author(s):  
Jahed Hossain ◽  
Erik Fernandez ◽  
Christian Garrett ◽  
Jay Kapat
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Flow Field ◽  
Mean Flow ◽  
Single Row ◽  
Flow And Heat Transfer ◽  
Turbulent Statistics ◽  
Flow Phenomena ◽  
The Mean ◽  
Channel Configuration

The present study aims to understand the flow, turbulence, and heat transfer in a single row narrow impingement channel for gas turbine heat transfer applications. Since the advent of several advanced manufacturing techniques, narrow wall cooling schemes have become more practical. In this study, the Reynolds number based on jet diameter was ≃15,000, with the jet plate having fixed jet hole diameters and hole spacing. The height of the channel is 3 times the impingement jet diameter. The channel width is 4 times the jet diameter of the impingement hole. The channel configuration was chosen such that the crossflow air is drawn out in the streamwise direction (maximum crossflow configuration). The impinging jets and the wall jets play a substantial role in removing heat in this kind of configuration. Hence, it is important to understand the evolution of flow and heat transfer in a channel of this configuration. The dynamics of flow and heat transfer in a single row narrow impingement channel are experimentally and numerically investigated. Particle Image Velocimetry (PIV) was used to reveal the detailed information of flow phenomena. The detailed PIV experiment was performed on this kind of impingement channel to satisfy the need for experimental data for this kind of impingement configuration, in order to validate turbulence models. PIV measurements were taken at a plane normal to the target wall along the jet centerline. The mean velocity field and turbulent statistics generated from the mean flow field were analyzed. The experimental data from the PIV reveals that flow is highly anisotropic in a narrow impingement channel. To support experimental data, wall-modeled Large Eddy Simulation (LES), and Reynolds Averaged Navier-Stokes (RANS) simulations (SST k-ω, v2–f, and Reynolds Stress Model (RSM)) were performed in the same channel geometry. The Wall-Adapting Local Eddy-viscosity SGS mdoel (WALE) [1] is used for the LES calculation. Mean velocities calculated from the RANS and LES were compared with the PIV data. Turbulent kinetic energy budgets were calculated from the experiment, and were compared with the LES and RSM model, highlighting the major shortcomings of RANS models to predict correct heat transfer behavior for the impingement problem. Temperature Sensitive Paint (TSP) was also used to experimentally obtain a local heat transfer distribution at the target and the side walls. An attempt was made to connect the complex aerodynamic flow behavior with results obtained from heat transfer, indicating heat transfer is a manifestation of flow phenomena. The accuracy of LES in predicting the mean flow field, turbulent statistics, and heat transfer is shown in the current work as it is validated against the experimental data through PIV and TSP.

Flow and Heat Transfer Analysis in a Single Row Narrow Impingement Channel: Comparison of Particle Image Velocimetry, Large Eddy Simulation, and RANS to Identify RANS Limitations

2017 ◽  
Vol 140 (3) ◽  
Author(s):  
Jahed Hossain ◽  
Erik Fernandez ◽  
Christian Garrett ◽  
Jayanta Kapat
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Mean Flow ◽  
Single Row ◽  
Eddy Simulation ◽  
Flow And Heat Transfer ◽  
Turbulent Statistics ◽  
Image Velocimetry ◽  
Flow Phenomena ◽  
The Mean

The present study aims to understand the flow, turbulence, and heat transfer in a single row narrow impingement channel for gas turbine heat transfer applications. Since the advent of several advanced manufacturing techniques, narrow wall cooling schemes have become more practical. In this study, the Reynolds number based on jet diameter was ≃15,000, with the jet plate having fixed jet hole diameters and hole spacing. The height of the channel is three times the impingement jet diameter. The channel width is four times the jet diameter of the impingement hole. The dynamics of flow and heat transfer in a single row narrow impingement channel are experimentally and numerically investigated. Particle image velocimetry (PIV) was used to reveal the detailed information of flow phenomena. PIV measurements were taken at a plane normal to the target wall along the jet centerline. The mean velocity field and the turbulent statistics generated from the mean flow field were analyzed. The experimental data from the PIV reveal that the flow is highly anisotropic in a narrow impingement channel. To support experimental data, wall-modeled large eddy simulation (LES) and Reynolds-averaged Navier–Stokes (RANS) simulations (shear stress transport k–ω, ν2−f, and Reynolds stress model (RSM)) were performed in the same channel geometry. Mean velocities calculated from the RANS and LES were compared with the PIV data. Turbulent kinetic energy budgets were calculated from the experiment, and were compared with the LES and RSM model, highlighting the major shortcomings of RANS models to predict correct heat transfer behavior for the impingement problem. Temperature-sensitive paint (TSP) was also used to experimentally obtain a local heat transfer distribution at the target and the side walls. An attempt was made to connect the complex aerodynamic flow behavior with the results obtained from heat transfer, indicating heat transfer is a manifestation of flow phenomena. The accuracy of LES in predicting the mean flow field, turbulent statistics, and heat transfer is shown in the current work as it is validated against the experimental data through PIV and TSP.

The evolution of round zero-net-mass-flux jets

2002 ◽  
Vol 472 ◽  
pp. 167-200 ◽  
Author(s):  
JOHN E. CATER ◽  
JULIO SORIA
Keyword(s):  
Mass Flux ◽  
Near Field ◽  
Spreading Rate ◽  
Velocity Fields ◽  
Mean Flow ◽  
Turbulent Statistics ◽  
Out Of Plane ◽  
Observed Behaviour ◽  
The Difference ◽  
Zero Net Mass Flux

This paper reports on an experimental investigation to determine the structure and mean flow quantities of round zero-net-mass-flux (ZNMF) jets. These jets are generated by a piston oscillating in a cavity behind a circular orifice. Several different flow patterns were observed with dye flow visualization and a parameter map of these was generated. Cross-correlation digital particle image velocimetry was used to measure instantaneous two-dimensional in-plane velocity fields in a plane containing the orifice axis. These velocity fields are used to investigate the existence of a self-preserving velocity profile in the far field of the ZNMF jet. The mean flow quantities and turbulent statistics of the ZNMF jets were compared with measurements for ‘equivalent’ continuous jets in the same apparatus. Phase-averaged velocity measurements were obtained in the near field of the ZNMF jets and were used to determine the radial entrainment. The out-of-plane vorticity fields were also investigated to gain an understanding of the mechanisms responsible for the difference in spreading rate of ZNMF jets compared to conventional continuous jets. A conceptual model of the ZNMF jet structure in the near field for Strouhal numbers much less than one is proposed that explains the observed behaviour of these ZNMF jets.

scholarly journals Instability wave models for the near-field fluctuations of turbulent jets

2011 ◽  
Vol 689 ◽  
pp. 97-128 ◽  
Author(s):  
K. Gudmundsson ◽  
Tim Colonius
Keyword(s):  
Flow Field ◽  
Large Scale ◽  
Microphone Array ◽  
Near Field ◽  
Turbulent Jets ◽  
Instability Wave ◽  
Mean Flow ◽  
Velocity Fluctuations ◽  
The Mean ◽  
Scale Structures

AbstractPrevious work has shown that aspects of the evolution of large-scale structures, particularly in forced and transitional mixing layers and jets, can be described by linear and nonlinear stability theories. However, questions persist as to the choice of the basic (steady) flow field to perturb, and the extent to which disturbances in natural (unforced), initially turbulent jets may be modelled with the theory. For unforced jets, identification is made difficult by the lack of a phase reference that would permit a portion of the signal associated with the instability wave to be isolated from other, uncorrelated fluctuations. In this paper, we investigate the extent to which pressure and velocity fluctuations in subsonic, turbulent round jets can be described aslinearperturbations to the mean flow field. The disturbances are expanded about the experimentally measured jet mean flow field, and evolved using linear parabolized stability equations (PSE) that account, in an approximate way, for the weakly non-parallel jet mean flow field. We utilize data from an extensive microphone array that measures pressure fluctuations just outside the jet shear layer to show that, up to an unknown initial disturbance spectrum, the phase, wavelength, and amplitude envelope of convecting wavepackets agree well with PSE solutions at frequencies and azimuthal wavenumbers that can be accurately measured with the array. We next apply the proper orthogonal decomposition to near-field velocity fluctuations measured with particle image velocimetry, and show that the structure of the most energetic modes is also similar to eigenfunctions from the linear theory. Importantly, the amplitudes of the modes inferred from the velocity fluctuations are in reasonable agreement with those identified from the microphone array. The results therefore suggest that, to predict, with reasonable accuracy, the evolution of the largest-scale structures that comprise the most energetic portion of the turbulent spectrum of natural jets, nonlinear effects need only be indirectly accounted for by considering perturbations to the mean turbulent flow field, while neglecting any non-zero frequency disturbance interactions.

An Investigation of Flow Fields Over Multi-Element Aerofoils

2001 ◽  
Vol 124 (1) ◽  
pp. 154-165 ◽  
Author(s):  
S. R. Maddah ◽  
H. H. Bruun
Keyword(s):  
Flow Field ◽  
Computational Study ◽  
Separated Flow ◽  
Mean Flow ◽  
Model Configuration ◽  
Attached Flow ◽  
The Mean ◽  
Flap Deflection ◽  
Comparative Results ◽  
Lift And Drag

This paper presents results obtained from a combined experimental and computational study of the flow field over a multi-element aerofoil with and without an advanced slat. Detailed measurements of the mean flow and turbulent quantities over a multi-element aerofoil model in a wind tunnel have been carried out using stationary and flying hot-wire (FHW) probes. The model configuration which spans the test section 600mm×600mm, is made of three parts: 1) an advanced (heel-less) slat, 2) a NACA 4412 main aerofoil and 3) a NACA 4415 flap. The chord lengths of the elements were 38, 250 and 83 mm, respectively. The results were obtained at a chord Reynolds number of 3×105 and a free Mach number of less than 0.1. The variations in the flow field are explained with reference to three distinct flow field regimes: attached flow, intermittent separated flow, and separated flow. Initial comparative results are presented for the single main aerofoil and the main aerofoil with a nondeflected flap at angles of attacks of 5, 10, and 15 deg. This is followed by the results for the three-element aerofoil with emphasis on the slat performance at angles of attack α=10, 15, 20, and 25 deg. Results are discussed both for a nondeflected flap δf=0deg and a deflected flap δf=25deg. The measurements presented are combined with other related aerofoil measurements to explain the main interaction of the slat/main aerofoil and main aerofoil/flap both for nondeflected and deflected flap conditions. These results are linked to numerically calculated variations in lift and drag coefficients with angle of attack and flap deflection angle.

Measurement of the Mean Flow Field in a Smooth Rotating Channel With Coriolis and Buoyancy Effects

2017 ◽  
Author(s):  
Ruquan You ◽  
Haiwang Li ◽  
Zhi Tao ◽  
Kuan Wei
Keyword(s):  
Flow Field ◽  
Coriolis Force ◽  
Indium Tin Oxide ◽  
Buoyancy Force ◽  
Flow Direction ◽  
Density Ratio ◽  
Mean Flow ◽  
The Mean ◽  
Static Conditions ◽  
Rotating Channel

The mean flow field in a smooth rotating channel was measured by particle image velocimetry under the effect of buoyancy force. In the experiments, the Reynolds number, based on the channel hydraulic diameter (D) and the bulk mean velocity (Um), is 10000, and the rotation numbers are 0, 0.13, 0.26, 0.39, 0.52, respectively. The four channel walls are heated with Indium Tin Oxide (ITO) heater glass, making the density ratio (d.r.) about 0.1 and the maximum value of buoyancy number up to 0.27. The mean flow field was simulated on a 3D reconstruction at the position of 3.5<X/D<6.5, where X is along the mean flow direction. The effect of Coriolis force and buoyancy force on the mean flow was taken into consideration in the current work. The results show that the Coriolis force pushes the mean flow to the trailing side, making the asymmetry of the mean flow with that in the static conditions. On the leading surface, due to the effect of buoyancy force, the mean flow field changes considerably. Comparing with the case without buoyancy force, separated flow was captured by PIV on the leading side in the case with buoyancy force. More details of the flow field will be presented in this work.

Influences of Turbulence Boundary Conditions on RANS and URANS Simulations for an Inter-Turbine Duct

2020 ◽  
Author(s):  
Alessio Firrito ◽  
Yannick Bousquet ◽  
Nicolas Binder ◽  
Ludovic Pintat
Keyword(s):  
Flow Field ◽  
Boundary Conditions ◽  
Mean Flow ◽  
Time Resolved ◽  
Flow Solution ◽  
Low Pressure Turbine ◽  
Outlet Flow ◽  
Architecture Evolution ◽  
The Mean ◽  
Turbulence Length

Abstract In recent years, lot of turbine research is focused on the study and optimization of inter-turbine ducts, an aero-engine component for which the design is becoming more challenging due to the turbofan architecture evolution. Starting from the early design phase, the knowledge of the component performance and outlet flow pattern is crucial in the design of the low pressure turbine. To improve prediction, multi-row unsteady simulations are deployed. Unfortunately, some questions arise in the use of these simulations, among others the knowledge of the turbulent boundary conditions and the contribution of the unsteady simulations to the flow solution. In this paper steady and time resolved RANS simulations of a turning inter-turbine duct are investigated. Particularly, two questions are addressed. The first one is the influence of the turbulent quantities boundary conditions in the case of a k–ω Wilcox turbulence model in the flow field solution. The second one is the contribution of the unsteadiness to the mean flow prediction. It will be shown that the mean flow depends on inlet turbulence only if the turbulence length scale is relatively high; otherwise the flow field is almost turbulence-invariant. For the unsteady simulations, unsteadiness modifies the mean flow solution only with low inlet turbulence.

Effects of the Interaction Point of Multi-Passage Swirlers on the Swirling Flow Field

2019 ◽  
Vol 141 (6) ◽  
Author(s):  
Foad Vashahi ◽  
Jeekeun Lee
Keyword(s):  
Geometrical Parameter ◽  
Swirling Flow ◽  
Energy Levels ◽  
Fuel Mixture ◽  
Mean Flow ◽  
Interaction Point ◽  
Stagnation Points ◽  
Image Velocimetry ◽  
The Mean ◽  
Proper Orthogonal

An experimental study is conducted to understand the mean and instantaneous behavior of the swirling flow issued from a triple swirler influenced by a single critical geometrical parameter, termed as the passage length. The investigated geometrical parameter defines the interaction point of the inner axial swirlers with the outer radial swirler, which consequently defines the primary air–fuel mixture characteristics and the resultant combustion state. Experiments were performed under cold flow conditions, and planar particle image velocimetry was employed to measure the velocity field. The mean flow pattern exhibited significant differences in terms of the swirl-jet width and angle and altered the number of stagnation points on the swirler axis. When the passage length was reduced to half, two stagnation points appeared on the swirler axis due to an initially developed smaller recirculation zone at the swirler mouth. Also, the turbulent activity at the vicinity of the swirler increased with as the passage length reduced. Investigations on the relocation of the second stagnation point on the axis through an arbitrary window revealed identical standard deviation in x and y directions. The energetic coherent structures extracted from the proper orthogonal decomposition also identified major differences in terms of the spatial distribution of the modes and their corresponding energy levels. The experimental results indicated that if the passage length is altered, the number of stagnation points on the swirler axis increases, and a breakdown of both the bubble and cone vortex may appear at the same time as different energy levels.

Sign in / Sign up

Export Citation Format

Share Document