The Optimum Cage Position and Orientation on the ALIF with Facet Screw Fixation: A Finite Element Analysis and the Taguchi Method

2011 ◽  
Vol 27 (3) ◽  
pp. 309-320 ◽  
Author(s):  
C.-Y. Fan ◽  
C.-K. Chao ◽  
C.-C. Hsu ◽  
K.-H. Chao
Keyword(s):  
Finite Element ◽  
Taguchi Method ◽  
Screw Fixation ◽  
Three Dimensional ◽  
Element Model ◽  
Lateral Position ◽  
Element Analysis ◽  
Control Factors ◽  
Position And Orientation ◽  
Noise Factors

ABSTRACTAnterior Lumbar Interbody Fusion (ALIF) has been widely used to treat internal disc degeneration. However, different cage positions and their orientations may affect the initial stability leading to different fusion results. The purpose of the present study is to investigate the optimum cage position and orientation for aiding an ALIF having a transfacet pedicle screw fixation (TFPS). A three-dimensional finite element model (ALIF with TFPS) has been developed to simulate the stability of the L4/L5 fusion segment under five different loading conditions. The Taguchi method was used to evaluate the optimized placement of the cages. Three control factors and two noise factors were included in the parameter design. The control factors included the anterior-posterior position, the medio-lateral position, and the convergent-divergent angle between the two cages. The compressive preload and the strengths of the cancellous bone were set as noise factors. From the results of the FEA and the Taguchi method, we suggest that the optimal cage positioning has a wide anterior placement, and a diverging angle between the two cages. The results show that the optimum cage position simultaneously contributes to a stronger support of the anterior column and lowers the risk of TFPS loosening.

scholarly journals Establishment of a Finite Element Model and Biomechanical Analysis of Different Fixation Methods for Total Talar Prosthesis Replacement

2021 ◽  
Author(s):  
Qian dong Yang ◽  
Le Chang ◽  
Xuting Bian ◽  
Lin Ma ◽  
Tao Xu ◽  
...  
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Screw Fixation ◽  
Articular Surface ◽  
Three Dimensional ◽  
Element Model ◽  
Element Analysis ◽  
Ankle Motion ◽  
Fixation Methods ◽  
Without Screws

Abstract Back ground：A three-dimensional finite element model of the whole foot with high geometric similarity was established and used to simulate the conditions after whole talar prosthesis implantation with several fixation methods, including Screw fixation of subtalar+talus-navicular joint, fixation with screws at only the subtalar joint, and fixation without screws. The biomechanical characteristics of the talus prosthesis were assessed in different gait phases to guide the selection of surgical methods in clinical practice.Methods：With the three-dimensional CT data of a volunteer's foot, Mimics13.0 and Geomagic10.0 software were used to carry out geometric reconstruction of the ankle-related tissues, and Hypermesh10.0 software was used for grid division and material attribute selection. Finally, the data were imported into Abaqus 6.9, and the simulated screw data were applied to different models. Finite element models with different fixation methods were simulated, and the stresses exerted by the human body in three gait phases (heel-strike, midstance and push-off) were simulated. The pressure changes in the articular surface around the talus or the prosthesis, the micromotion of the talus and the prosthesis and ankle motion were measured. Results：Finite element analysis on the biomechanical mechanism showed that screw fixation of the prosthesis in different gait phases mainly increases the pressure on the tibialis articular surface as well as decreases the pressure on the fused articular surface and joint micromotion, which hinders ankle motion. The indicator values were nearly the same in the models of fixation without screws and the normal state.Conclusion：The 3D finite element model created in this study has been verified to be an accurate and reliable model. The biomechanical mechanism varies by fixation method according to finite element analysis. Fixation of the prosthesis without screws yields values most similar to normal values.

Torsional Analysis of a Steel Cord-Rubber Tire Belt Structure

1996 ◽  
Vol 24 (4) ◽  
pp. 339-348 ◽  
Author(s):  
R. M. V. Pidaparti
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Composite Structures ◽  
Three Dimensional ◽  
Element Model ◽  
Torsional Stiffness ◽  
Element Analysis ◽  
Rubber Belt ◽  
Steel Cord ◽  
Torsional Analysis

Abstract A three-dimensional (3D) beam finite element model was developed to investigate the torsional stiffness of a twisted steel-reinforced cord-rubber belt structure. The present 3D beam element takes into account the coupled extension, bending, and twisting deformations characteristic of the complex behavior of cord-rubber composite structures. The extension-twisting coupling due to the twisted nature of the cords was also considered in the finite element model. The results of torsional stiffness obtained from the finite element analysis for twisted cords and the two-ply steel cord-rubber belt structure are compared to the experimental data and other alternate solutions available in the literature. The effects of cord orientation, anisotropy, and rubber core surrounding the twisted cords on the torsional stiffness properties are presented and discussed.

Finite Element Analysis of Nonuniformity of Tires with Imperfections5

2007 ◽  
Vol 35 (3) ◽  
pp. 226-238 ◽  
Author(s):  
K. M. Jeong ◽  
K. W. Kim ◽  
H. G. Beom ◽  
J. U. Park
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Radial Force ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Dimensional Finite Element ◽  
Force Variation ◽  
Three Dimensional Finite Element

Abstract The effects of variations in stiffness and geometry on the nonuniformity of tires are investigated by using the finite element analysis. In order to evaluate tire uniformity, a three-dimensional finite element model of the tire with imperfections is developed. This paper considers how imperfections, such as variations in stiffness or geometry and run-out, contribute to detrimental effects on tire nonuniformity. It is found that the radial force variation of a tire with imperfections depends strongly on the geometrical variations of the tire.

scholarly journals Comparison of Tooth- and Bone-Borne Appliances on the Stress Distributions and Displacement Patterns in the Facial Skeleton in Surgically Assisted Rapid Maxillary Expansion—A Finite Element Analysis (FEA) Study

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1152
Author(s):  
Rafał Nowak ◽  
Anna Olejnik ◽  
Hanna Gerber ◽  
Roman Frątczak ◽  
Ewa Zawiślak
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Rapid Maxillary Expansion ◽  
Stress Distributions ◽  
Maxillary Expansion ◽  
Facial Skeleton ◽  
Element Analysis ◽  
Maxillary Constriction

The aim of this study was to compare the reduced stresses according to Huber’s hypothesis and the displacement pattern in the region of the facial skeleton using a tooth- or bone-borne appliance in surgically assisted rapid maxillary expansion (SARME). In the current literature, the lack of updated reports about biomechanical effects in bone-borne appliances used in SARME is noticeable. Finite element analysis (FEA) was used for this study. Six facial skeleton models were created, five with various variants of osteotomy and one without osteotomy. Two different appliances for maxillary expansion were used for each model. The three-dimensional (3D) model of the facial skeleton was created on the basis of spiral computed tomography (CT) scans of a 32-year-old patient with maxillary constriction. The finite element model was built using ANSYS 15.0 software, in which the computations were carried out. Stress distributions and displacement values along the 3D axes were found for each osteotomy variant with the expansion of the tooth- and the bone-borne devices at a level of 0.5 mm. The investigation showed that in the case of a full osteotomy of the maxilla, as described by Bell and Epker in 1976, the method of fixing the appliance for maxillary expansion had no impact on the distribution of the reduced stresses according to Huber’s hypothesis in the facial skeleton. In the case of the bone-borne appliance, the load on the teeth, which may lead to periodontal and orthodontic complications, was eliminated. In the case of a full osteotomy of the maxilla, displacements in the buccolingual direction for all the variables of the bone-borne appliance were slightly bigger than for the tooth-borne appliance.

Finite Element Analysis of the Effect of Surface Hardening Depth in Port Crane Wheel

2011 ◽  
Vol 291-294 ◽  
pp. 3282-3286 ◽  
Author(s):  
Jiang Wei Wu ◽  
Peng Wang
Keyword(s):  
Finite Element ◽  
Surface Hardening ◽  
Three Dimensional ◽  
Element Model ◽  
Contact Stresses ◽  
Numerical Results ◽  
Element Analysis ◽  
Finite Element Software ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element

In port crane industry, the surface hardening technique is widely used in order to improve the strength of wheel. But the hardening depth is chosen only by according to the experience, and the effect of different hardened depths is not studied theoretically. In this paper, the contact stresses in wheel with different hardening depth have been analyzed by applying three-dimensional finite element model. Based on this model, the ANSYS10.0 finite element software is used. The elastic wheel is used to verify the numerical results with the Hertz’s theory. Three different hardening depths, namely 10mm, 25mm and whole hardened wheel, under three different vertical loads were applied. The effect of hardening depth of a surface hardened wheel is discussed by comparing the contact stresses and contact areas from the numerical results.

Nonlinear Finite Element Analysis of Super-Long Pile and Soil Interaction in Soft Soil

2011 ◽  
Vol 201-203 ◽  
pp. 1601-1605 ◽  
Author(s):  
Shang Ping Chen ◽  
Wen Juan Yao ◽  
Sheng Qing Zhu
Keyword(s):  
Finite Element ◽  
Constitutive Model ◽  
Soft Soil ◽  
Three Dimensional ◽  
Nonlinear Behavior ◽  
Element Model ◽  
Element Analysis ◽  
Friction Resistance ◽  
Tip Resistance ◽  
Side Friction

In this paper, a nonlinear three-dimensional finite element model for super-long pile and soil interaction is established. In this model, contact elements are applied to simulate the nonlinear behavior of interaction of super-long pile and soil. A nonlinear elastic constitutive model for concrete is employed to analyze stress-strain relation of pile shaft under the axial load and the Duncan-Chang’s nonlinear constitutive model is used to reflect nonlinear and inelastic properties of soil. The side friction resistance, axial force, pile-tip resistance, and developing trend of soil plastic deformation are obtained and compared with measured results from static load tests. It is demonstrated that a super-long pile has the properties of degradation of side friction resistance and asynchronous action between side and pile-tip resistance, which is different from piles with a short to medium length.

Finite Element Analysis of Top-Hat–Stiffened Panels of Fiber-Reinforced–Plastic Boat Structures

2007 ◽  
Vol 44 (01) ◽  
pp. 16-26
Author(s):  
Ömer Eksik ◽  
R. Ajit Shenoi ◽  
Stuart S. J. Moy ◽  
Han Koo Jeong
Keyword(s):  
Finite Element ◽  
Lateral Pressure ◽  
Three Dimensional ◽  
Element Model ◽  
Stiffened Panel ◽  
Element Analysis ◽  
Stiffened Panels ◽  
Fiber Reinforced Plastic ◽  
Reinforced Plastic ◽  
Experimental Findings

This paper describes the development of a finite element model in order to assess the static response of a top-hat-stiffened panel under uniform lateral pressure. Systematic calculations were performed for deflection, strain, and stress using the developed model based on the ANSYS three-dimensional solid element (SOLID45). The numerical modeling results were compared to the experimental findings for validation and to further understand an internal stress pattern within the different constituents of the panel for explaining the likely causes of the panel failure. Good correlation between experimental and numerical strains and displacements was achieved.

scholarly journals A finite element analysis of sacroiliac joint displacements and ligament strains in response to three manipulations

2020 ◽  
Vol 21 (1) ◽  
Author(s):  
Zhun Xu ◽  
Yikai Li ◽  
Shaoqun Zhang ◽  
Liqing Liao ◽  
Kai Wu ◽  
...  
Keyword(s):  
Finite Element ◽  
Sacroiliac Joint ◽  
Clinical Effect ◽  
Three Dimensional ◽  
Element Model ◽  
Element Analysis ◽  
Ligament Strain ◽  
Dimensional Finite Element ◽  
The Right ◽  
Three Dimensional Finite Element

Abstract Background Clinical studies have found that manipulations have a good clinical effect on sacroiliac joint (SIJ) pain without specific causes. However, the specific mechanisms underlying the effect of manipulations are still unclear. The purpose of this study was to investigate the effects of three common manipulations on the stresses and displacements of the normal SIJ and the strains of the surrounding ligaments. Methods A three-dimensional finite element model of the pelvis-femur was developed. The manipulations of hip and knee flexion (MHKF), oblique pulling (MOP), and lower limb hyperextension (MLLH) were simulated. The stresses and displacements of the SIJ and the strains of the surrounding ligaments were analyzed during the three manipulations. Results MOP produced the highest stress on the left SIJ, at 6.6 MPa, while MHKF produced the lowest stress on the right SIJ, at 1.5 MPa. The displacements of the SIJ were all less than 1 mm during the three manipulations. The three manipulations caused different degrees of ligament strain around the SIJ, and MOP produced the greatest straining of the ligaments. Conclusion The three manipulations all produced small displacements of the SIJ and different degrees of ligament strains, which might be the mechanism through which they relieve SIJ pain. MOP produced the largest displacement and the greatest ligament strains.

Finite Element Analysis for Gear Contact Based on UG and ABAQUS

2013 ◽  
Vol 442 ◽  
pp. 229-232 ◽  
Author(s):  
Li Mei Wu ◽  
Fei Yang
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Contact Stress ◽  
Three Dimensional ◽  
Element Model ◽  
Tooth Surface ◽  
Element Analysis ◽  
Tooth Width ◽  
Gear Contact ◽  
Maximum Contact

According to the cutting theory of involute tooth profile, established an exact three-dimensional parametric model by UG. Used ABAQUS to crate finite element model for gear meshing. After simulated the meshing process, discussed the periodicity of the tooth surface contact stress. Based on the result of finite element analysis, made a comparison of the maximum contact stress between finite element solution and Hertz theoretical solution, analyzed the contact stress distribution on tooth width, and researched the effect of friction factor on contact stress. All that provided some theoretical basis for gear contact strength design.

Sign in / Sign up

Export Citation Format

Share Document