On convenient use of nanoprobe and scanning without a stem unit in an EM-420

1987 ◽  
Vol 45 ◽  
pp. 138-139
Author(s):  
K. K. Christenson ◽  
J. A. Eades
Keyword(s):  
Wide Area ◽  
Pole Piece ◽  
Operating Condition ◽  
Objective System

One of the strengths of the Philips EM-400 series of TEMs is their ability to operate under two distinct optical configurations: “microprobe”, the normal TEM operating condition which allows wide area illumination, and “nanoprobe”, which gives very small probes with high angular convergence for STEM imaging, microchemical and microstructural analyses. This change is accomplished by effectively turning off the twin lens located in the upper pole piece which changes the illumination from a telefocus system to a condenser-objective system. The deflection and tilt controls and alignments are designed for microprobe use and do not function properly when in nanoprobe. For instance, in nanoprobe the deflection control gives a mix of deflection and tilt; as does the tilt control.

Field Distribution of Strongly Excited Magnetic Lenses

1975 ◽  
Vol 33 ◽  
pp. 140-141
Author(s):  
M. Strojnik
Keyword(s):  
Flux Density ◽  
Field Distribution ◽  
Optical Axis ◽  
Operating Point ◽  
Pole Piece ◽  
Partial Saturation ◽  
Axial Flux ◽  
The Stability

Magnetic lenses operating in partial saturation offer two advantages in HVEM: they exhibit small cs and cc and their power depends little on the excitation IN. Curve H, Fig. 1, shows that the maximal axial flux density Bz max of one of the lenses investigated changes between points (3) and (4) by 5% as the excitation varies by 40%. Consequently, the designer can relax the requirements concerning the stability of the lens current supplies. Saturated lenses, however, can only be used if (i) unwanted fields along the optical axis can be controlled, (ii) 'wobbling' of the optical axis due to inhomogeneous saturation around the pole piece faces is prevented, (iii) ample ampere-turns can be squeezed into the space available, and (iv) the lens operating point covers a sufficient range of accelerating voltages.

Algorithms for automated montage synthesis of images from laser-scanning confocal microscopes

1995 ◽  
Vol 53 ◽  
pp. 650-651
Author(s):  
D. E. Becker
Keyword(s):  
Image Analysis ◽  
High Resolution ◽  
Laser Scanning ◽  
Cell Counting ◽  
Wide Area ◽  
Data Set ◽  
Computational Synthesis ◽  
Automated Cell Counting ◽  
Partial View ◽  
The Individual

An efficient, robust, and widely-applicable technique is presented for computational synthesis of high-resolution, wide-area images of a specimen from a series of overlapping partial views. This technique can also be used to combine the results of various forms of image analysis, such as segmentation, automated cell counting, deblurring, and neuron tracing, to generate representations that are equivalent to processing the large wide-area image, rather than the individual partial views. This can be a first step towards quantitation of the higher-level tissue architecture. The computational approach overcomes mechanical limitations, such as hysterisis and backlash, of microscope stages. It also automates a procedure that is currently done manually. One application is the high-resolution visualization and/or quantitation of large batches of specimens that are much wider than the field of view of the microscope.The automated montage synthesis begins by computing a concise set of landmark points for each partial view. The type of landmarks used can vary greatly depending on the images of interest. In many cases, image analysis performed on each data set can provide useful landmarks. Even when no such “natural” landmarks are available, image processing can often provide useful landmarks.

Convergent Beam Electron Diffraction Zone Axis Pattern Map of Zirconium

1990 ◽  
Vol 48 (2) ◽  
pp. 496-497
Author(s):  
E. Silva ◽  
R. Scozia
Keyword(s):  
Electron Diffraction ◽  
Convergent Beam Electron Diffraction ◽  
Zone Axis ◽  
Pole Piece ◽  
Small Particles ◽  
Present Communication ◽  
Beam Electron ◽  
Zero Layer ◽  
Set Up ◽  
Convergent Beam

The purpose in obtaining zone axis pattern map (zap map) from a given material is to provide a quick and reliable tool to identify cristaline phases, and crystallographic directions, even in small particles. Bend contours patterns and Kossel lines patterns maps from Zr single crystal in the [0001] direction have been presented previously. In the present communication convergent beam electron diffraction (CBED) zap map of Zr will be shown. CBED patterns were obtained using a Philips microscope model EM300, which was set up to carry out this technique. Convergent objective upper pole piece for STEM and some electronic modifications in the lens circuits were required, furthermore the microscope was carefully cleaned and it was operated at a vacuum eminently good.CBED patterns in the Zr zap map consist of zero layer disks, showing fine details within them which correspond to intersecting set of higher order Laue zone (HOLZ) deficiency lines.

Theoretical And Practical Design Considerations for Ultra-High Resolution Electron Lenses

1980 ◽  
Vol 38 ◽  
pp. 266-269
Author(s):  
Y. Harada ◽  
K. Tsuno ◽  
Y. Arai
Keyword(s):  
Optical Properties ◽  
High Resolution ◽  
Chromatic Aberration ◽  
Point Of View ◽  
Pole Piece ◽  
Axial Field ◽  
Design Considerations ◽  
Resolution Electron ◽  
Practical Design ◽  
Peak Flux

Magnetic objective lenses, from the point of view of pole piece geometry, can he roughly classified into two types, viz., symmetrical and asymmetrical. In the case of the former, the optical properties have been calculated by several authors1-3) and the results would appear to suggest that, in order to reduce the spherical and chromatic aberration coefficients, Cs and Cc, it is necessary to decrease the half-width value of the axial field distribution and to increase the peak flux density. The expressions for either minimum Cs or minimum Cc were presented in the form of ‘universal’ curves by Mulvey and Wallington4).

OPERATIONAL STATE OF BRIDGES OF UKRAINE

2019 ◽  
pp. 57-68
Author(s):  
Larysa Bodnar ◽  
Petro Koval ◽  
Sergii Stepanov ◽  
Liudmyla Panibratets
Keyword(s):  
Management System ◽  
The State ◽  
Operating Conditions ◽  
Bridge Management ◽  
Bridge Management System ◽  
Program Complex ◽  
Operating Condition ◽  
Software Complex ◽  
Automatic Mode ◽  
The Status

A significant part of Ukrainian bridges on public roads is operated for more than 30 years (94 %). At the same time, the traffic volume and the weight of vehicles has increased significantly. Insufficient level of bridges maintenance funding leads to the deterioration of their technical state. The ways to ensure reliable and safe operation of bridges are considered. The procedure for determining the predicted operational status of the elements and the bridge in general, which has a scientific novelty, is proposed. In the software complex, Analytical Expert Bridges Management System (AESUM), is a function that allows tracking the changes in the operational status of bridges both in Ukraine and in each region separately. The given algorithm of the procedure for determining the predicted state of the bridge using a degradation model is described using the Nassie-Schneidermann diagram. The model of the degradation of the bridge performance which is adopted in Ukraine as a normative one, and the algorithm for its adaptation to the AESUM program complex with the function to ensure the probabilistic predicted operating condition of the bridges in the automatic mode is presented. This makes it possible, even in case of unsatisfactory performance of surveys, to have the predicted lifetime of bridges at the required time. For each bridge element it is possible to determine the residual time of operation that will allow predict the state of the elements of the structure for a certain period of time in the future. Significant interest for specialists calls for the approaches to the development of orientated perspective plans for bridge inspection and monitoring of changes in the operational status of bridges for 2009-2018 in Ukraine. For the analysis of the state of the bridge economy, the information is available on the distribution of bridges by operating state related to the administrative significance of roads, by road categories and by materials of the structures. Determining the operating state of the bridge is an important condition for making the qualified decisions as regards its maintenance. The Analytical Expert Bridges Management System (AESUM) which is implemented in Ukraine, stores the data on the monitoring the status of bridges and performs the necessary procedures to maintain them in a reliable and safe operating condition. An important result of the work is the ability to determine the distribution of bridges on the public roads of Ukraine, according to operating conditions established in the program complex of AESUM, which is presented in accordance with the data of the current year. In conditions of limited funding and in case of unsatisfactory performance of surveys, it is possible to make the reasonable management decisions regarding the repair and the reconstruction of bridges. Keywords: bridge management system, operating condition, predicted operating condition, model of degradation, bridge survey plan, highway bridge.

Possibilities for realizing a wide-area differential navigation using the GPS and GLONASS signals in Ukraine

1998 ◽  
Vol 4 (5-6) ◽  
pp. 56-61 ◽  
Author(s):  
A.P. Vereshak ◽  
◽  
A.A. Zhalilo ◽  
I.G. Nozdrin ◽  
S.N. Flerko ◽  
...  
Keyword(s):  
Wide Area
Sign in / Sign up

Export Citation Format

Share Document