scholarly journals Optical actuation of a micromechanical photodiode via the photovoltaic-piezoelectric effect

2021 ◽  
Vol 7 (1) ◽  
Author(s):  
A. Rampal ◽  
R. N. Kleiman
Keyword(s):  
Molecular Beam ◽  
Piezoelectric Effect ◽  
Piezoelectric Materials ◽  
Quantum Circuits ◽  
Direct Piezoelectric Effect ◽  
Electro Optic ◽  
Potential Applications ◽  
New Type ◽  
Optical Circuits ◽  
Lattice Matched

AbstractRadiation pressure and photothermal forces have been previously used to optically actuate micro/nanomechanical structures fabricated from semiconductor piezoelectric materials such as gallium arsenide (GaAs). In these materials, coupling of the photovoltaic and piezoelectric properties has not been fully explored and leads to a new type of optical actuation that we call the photovoltaic-piezoelectric effect (PVPZ). We demonstrate this effect by electrically measuring, via the direct piezoelectric effect, the optically induced strain in a novel torsional resonator. The micron-scale torsional resonator is fabricated from a lattice-matched single-crystal molecular beam epitaxy (MBE)-grown GaAs photodiode heterostructure. We find that the strain depends on the product of the electro-optic responsivity and piezoelectric constant of GaAs. The photovoltaic-piezoelectric effect has important potential applications, such as in the development of configurable optical circuits, which can be used in neuromorphic photonic chips, processing of big data with deep learning and the development of quantum circuits.

scholarly journals Static Force Measurement Using Piezoelectric Sensors

2021 ◽  
Vol 2021 ◽  
pp. 1-8
Author(s):  
Kyungrim Kim ◽  
Jinwook Kim ◽  
Xiaoning Jiang ◽  
Taeyang Kim
Keyword(s):  
Surface Charge ◽  
Piezoelectric Effect ◽  
Force Measurement ◽  
Piezoelectric Materials ◽  
Force Sensor ◽  
Piezoelectric Sensors ◽  
Force Sensing ◽  
Static Force ◽  
Sensing Applications ◽  
Direct Piezoelectric Effect

In force measurement applications, a piezoelectric force sensor is one of the most popular sensors due to its advantages of low cost, linear response, and high sensitivity. Piezoelectric sensors effectively convert dynamic forces to electrical signals by the direct piezoelectric effect, but their use has been limited in measuring static forces due to the easily neutralized surface charge. To overcome this shortcoming, several static (either pure static or quasistatic) force sensing techniques using piezoelectric materials have been developed utilizing several unique parameters rather than just the surface charge produced by an applied force. The parameters for static force measurement include the resonance frequency, electrical impedance, decay time constant, and capacitance. In this review, we discuss the detailed mechanism of these piezoelectric-type, static force sensing methods that use more than the direct piezoelectric effect. We also highlight the challenges and potentials of each method for static force sensing applications.

Metal-Core Piezoelectric Fibers for the Detection of Lamb Waves

2010 ◽  
Author(s):  
Jian Liu ◽  
Jinhao Qiu ◽  
Weijie Chang ◽  
Hongli Ji ◽  
Kongjun Zhu
Keyword(s):  
Lamb Wave ◽  
Piezoelectric Effect ◽  
Lamb Waves ◽  
Guided Wave ◽  
Voltage Response ◽  
Metal Core ◽  
Direct Piezoelectric Effect ◽  
New Type ◽  
Sensor Voltage ◽  
Piezoelectric Fiber

Metal-core piezoelectric fiber (MPF) is a new type of piezoelectric ceramic device with small size, and has great potential to be used as structurally integrated transducers for guided-wave (GW) structural health monitoring. This paper focuses on the use of MPF as ultrasonic Lamb wave receivers. First, the MPF sensor voltage response is derived by coupling the direct piezoelectric effect to the wave strain field excited by circular crested actuator. The obtained theoretical result is validated on an aluminum plate. Furthermore, the experiment that compares the MPF response to Lamb wave with the PZT response is performed. The results show that MPF sensors can be used to sense Lamb waves clearly. In the end, the directivity of MPF response to Lamb waves was investigated, and another experiment is performed to examine the directivity of MPF response to Lamb waves. The result shows that MPF has high directivity, which can be exploited to triangulate the location of an ultrasound source without prior knowledge of the wave velocity in the medium.

A New Structure of a Force Sensor Based on the Analysis of Electromechanical Impedance

2011 ◽  
Vol 179-180 ◽  
pp. 793-800
Author(s):  
Jing Fu Li ◽  
Zhi Jun Long
Keyword(s):  
Piezoelectric Effect ◽  
Piezoelectric Materials ◽  
Force Sensor ◽  
Dynamic Force ◽  
Static Force ◽  
Electromechanical Impedance ◽  
Direct Piezoelectric Effect ◽  
Impedance Technique

In this article a new structure of a force sensor based on piezoelectric materials is proposed. The design and choice of measuring principle is based on the direct piezoelectric effect, for the measurement of the dynamic force, and on the analysis of the electromechanical impedance technique, for measuring the static force. This technique is based on the measurement of modes of the structure. Indeed, the application of stress on the structure will cause changes in the modes of the structure and appearance of new eigenmodes. Thus far these methods should allow for measurement of static force applied.

scholarly journals Piezoelectric Polymer and Paper Substrates: A Review

Sensors ◽  
2018 ◽  
Vol 18 (11) ◽  
pp. 3605 ◽  
Author(s):  
Kiran Sappati ◽  
Sharmistha Bhadra
Keyword(s):  
Polymer Composites ◽  
Piezoelectric Properties ◽  
Piezoelectric Effect ◽  
Piezoelectric Materials ◽  
Fabrication Cost ◽  
Piezoelectric Polymers ◽  
Direct Piezoelectric Effect ◽  
Piezoelectric Polymer ◽  
Wide Range ◽  
Actuator Design

Polymers and papers, which exhibit piezoelectricity, find a wide range of applications in the industry. Ever since the discovery of PVDF, piezo polymers and papers have been widely used for sensor and actuator design. The direct piezoelectric effect has been used for sensor design, whereas the inverse piezoelectric effect has been applied for actuator design. Piezo polymers and papers have the advantages of mechanical flexibility, lower fabrication cost and faster processing over commonly used piezoelectric materials, such as PZT, BaTiO3. In addition, many polymer and paper materials are considered biocompatible and can be used in bio applications. In the last 20 years, heterostructural materials, such as polymer composites and hybrid paper, have received a lot of attention since they combine the flexibility of polymer or paper, and excellent pyroelectric and piezoelectric properties of ceramics. This paper gives an overview of piezoelectric polymers and papers based on their operating principle. Main categories of piezoelectric polymers and papers are discussed with a focus on their materials and fabrication techniques. Applications of piezoelectric polymers and papers in different areas are also presented.

An in situ and ex situ TEM study of the formation of thin cobalt silicide films by molecular beam epitaxy on the silicon (100) surface

1988 ◽  
Vol 46 ◽  
pp. 884-885
Author(s):  
D. Loretto ◽  
J. M. Gibson ◽  
S. M. Yalisove ◽  
R. T. Tung
Keyword(s):  
Molecular Beam Epitaxy ◽  
Molecular Beam ◽  
Defect Density ◽  
High Vacuum ◽  
Ultra High Vacuum ◽  
Ex Situ ◽  
Metal Base ◽  
In Situ Experiments ◽  
Potential Applications

The cobalt disilicide/silicon system has potential applications as a metal-base and as a permeable-base transistor. Although thin, low defect density, films of CoSi2 on Si(111) have been successfully grown, there are reasons to believe that Si(100)/CoSi2 may be better suited to the transmission of electrons at the silicon/silicide interface than Si(111)/CoSi2. A TEM study of the formation of CoSi2 on Si(100) is therefore being conducted. We have previously reported TEM observations on Si(111)/CoSi2 grown both in situ, in an ultra high vacuum (UHV) TEM and ex situ, in a conventional Molecular Beam Epitaxy system.The procedures used for the MBE growth have been described elsewhere. In situ experiments were performed in a JEOL 200CX electron microscope, extensively modified to give a vacuum of better than 10-9 T in the specimen region and the capacity to do in situ sample heating and deposition. Cobalt was deposited onto clean Si(100) samples by thermal evaporation from cobalt-coated Ta filaments.

scholarly journals Piezoelectric Energy Harvesting Solutions: A Review

Sensors ◽  
2020 ◽  
Vol 20 (12) ◽  
pp. 3512 ◽  
Author(s):  
Corina Covaci ◽  
Aurel Gontean
Keyword(s):  
Energy Harvesting ◽  
Piezoelectric Effect ◽  
Piezoelectric Transducers ◽  
Piezoelectric Energy Harvesting ◽  
Piezoelectric Energy ◽  
Direct Piezoelectric Effect ◽  
Harvesting Technique ◽  
Different Shapes ◽  
Piezoelectric Devices ◽  
Review Current

The goal of this paper is to review current methods of energy harvesting, while focusing on piezoelectric energy harvesting. The piezoelectric energy harvesting technique is based on the materials’ property of generating an electric field when a mechanical force is applied. This phenomenon is known as the direct piezoelectric effect. Piezoelectric transducers can be of different shapes and materials, making them suitable for a multitude of applications. To optimize the use of piezoelectric devices in applications, a model is needed to observe the behavior in the time and frequency domain. In addition to different aspects of piezoelectric modeling, this paper also presents several circuits used to maximize the energy harvested.

A New Type of Cuprous-Cysteamine Sensitizers: Synthesis, Optical Properties and Potential Applications

2021 ◽  
pp. 100435
Author(s):  
Yan Wang ◽  
Noura Dawas Alkhaldi ◽  
Nil Kanatha Pandey ◽  
Lalit Chudal ◽  
Lingyun Wang ◽  
...  
Keyword(s):  
Optical Properties ◽  
Potential Applications ◽  
New Type

Note: Direct piezoelectric effect microscopy

2015 ◽  
Vol 86 (7) ◽  
pp. 076102 ◽  
Author(s):  
T. J. A. Mori ◽  
P. Stamenov ◽  
L. S. Dorneles
Keyword(s):  
Piezoelectric Effect ◽  
Direct Piezoelectric Effect

WAVELENGTH DEMULTIPLEXING IN METAL–INSULATOR–METAL PLASMONIC WAVEGUIDES

2014 ◽  
Vol 28 (04) ◽  
pp. 1450025 ◽  
Author(s):  
XIANKUN YAO
Keyword(s):  
Transmission Efficiency ◽  
Plasmonic Waveguides ◽  
Metal Insulator ◽  
Metal Insulator Metal ◽  
Integrated Optical ◽  
Potential Applications ◽  
Wavelength Demultiplexing ◽  
Optical Circuits ◽  
Difference Time ◽  
Mim Waveguide

In this paper, we have numerically investigated a novel kind of ultra-compact wavelength demultiplexing (WDM) in high-confined metal–insulator–metal (MIM) plasmonic waveguides. It is found that the drop transmission efficiency of the filtering cavity can be strongly enhanced by introducing a side-coupled cavity in the MIM waveguide. The theoretical analysis is verified by the finite-difference time-domain simulations. Through cascading the filtering units, a highly effective triple-wavelength demultiplexer is proposed by selecting the specific separation between the two coupled cavities of filtering units. Our results may find potential applications for the nanoscale WDM systems in highly integrated optical circuits and networks.

Sign in / Sign up

Export Citation Format

Share Document