scholarly journals Piezoelectric Polymer and Paper Substrates: A Review

Sensors ◽  
2018 ◽  
Vol 18 (11) ◽  
pp. 3605 ◽  
Author(s):  
Kiran Sappati ◽  
Sharmistha Bhadra
Keyword(s):  
Polymer Composites ◽  
Piezoelectric Properties ◽  
Piezoelectric Effect ◽  
Piezoelectric Materials ◽  
Fabrication Cost ◽  
Piezoelectric Polymers ◽  
Direct Piezoelectric Effect ◽  
Piezoelectric Polymer ◽  
Wide Range ◽  
Actuator Design

Polymers and papers, which exhibit piezoelectricity, find a wide range of applications in the industry. Ever since the discovery of PVDF, piezo polymers and papers have been widely used for sensor and actuator design. The direct piezoelectric effect has been used for sensor design, whereas the inverse piezoelectric effect has been applied for actuator design. Piezo polymers and papers have the advantages of mechanical flexibility, lower fabrication cost and faster processing over commonly used piezoelectric materials, such as PZT, BaTiO3. In addition, many polymer and paper materials are considered biocompatible and can be used in bio applications. In the last 20 years, heterostructural materials, such as polymer composites and hybrid paper, have received a lot of attention since they combine the flexibility of polymer or paper, and excellent pyroelectric and piezoelectric properties of ceramics. This paper gives an overview of piezoelectric polymers and papers based on their operating principle. Main categories of piezoelectric polymers and papers are discussed with a focus on their materials and fabrication techniques. Applications of piezoelectric polymers and papers in different areas are also presented.

scholarly journals Static Force Measurement Using Piezoelectric Sensors

2021 ◽  
Vol 2021 ◽  
pp. 1-8
Author(s):  
Kyungrim Kim ◽  
Jinwook Kim ◽  
Xiaoning Jiang ◽  
Taeyang Kim
Keyword(s):  
Surface Charge ◽  
Piezoelectric Effect ◽  
Force Measurement ◽  
Piezoelectric Materials ◽  
Force Sensor ◽  
Piezoelectric Sensors ◽  
Force Sensing ◽  
Static Force ◽  
Sensing Applications ◽  
Direct Piezoelectric Effect

In force measurement applications, a piezoelectric force sensor is one of the most popular sensors due to its advantages of low cost, linear response, and high sensitivity. Piezoelectric sensors effectively convert dynamic forces to electrical signals by the direct piezoelectric effect, but their use has been limited in measuring static forces due to the easily neutralized surface charge. To overcome this shortcoming, several static (either pure static or quasistatic) force sensing techniques using piezoelectric materials have been developed utilizing several unique parameters rather than just the surface charge produced by an applied force. The parameters for static force measurement include the resonance frequency, electrical impedance, decay time constant, and capacitance. In this review, we discuss the detailed mechanism of these piezoelectric-type, static force sensing methods that use more than the direct piezoelectric effect. We also highlight the challenges and potentials of each method for static force sensing applications.

A New Structure of a Force Sensor Based on the Analysis of Electromechanical Impedance

2011 ◽  
Vol 179-180 ◽  
pp. 793-800
Author(s):  
Jing Fu Li ◽  
Zhi Jun Long
Keyword(s):  
Piezoelectric Effect ◽  
Piezoelectric Materials ◽  
Force Sensor ◽  
Dynamic Force ◽  
Static Force ◽  
Electromechanical Impedance ◽  
Direct Piezoelectric Effect ◽  
Impedance Technique

In this article a new structure of a force sensor based on piezoelectric materials is proposed. The design and choice of measuring principle is based on the direct piezoelectric effect, for the measurement of the dynamic force, and on the analysis of the electromechanical impedance technique, for measuring the static force. This technique is based on the measurement of modes of the structure. Indeed, the application of stress on the structure will cause changes in the modes of the structure and appearance of new eigenmodes. Thus far these methods should allow for measurement of static force applied.

scholarly journals Optical actuation of a micromechanical photodiode via the photovoltaic-piezoelectric effect

2021 ◽  
Vol 7 (1) ◽  
Author(s):  
A. Rampal ◽  
R. N. Kleiman
Keyword(s):  
Molecular Beam ◽  
Piezoelectric Effect ◽  
Piezoelectric Materials ◽  
Quantum Circuits ◽  
Direct Piezoelectric Effect ◽  
Electro Optic ◽  
Potential Applications ◽  
New Type ◽  
Optical Circuits ◽  
Lattice Matched

AbstractRadiation pressure and photothermal forces have been previously used to optically actuate micro/nanomechanical structures fabricated from semiconductor piezoelectric materials such as gallium arsenide (GaAs). In these materials, coupling of the photovoltaic and piezoelectric properties has not been fully explored and leads to a new type of optical actuation that we call the photovoltaic-piezoelectric effect (PVPZ). We demonstrate this effect by electrically measuring, via the direct piezoelectric effect, the optically induced strain in a novel torsional resonator. The micron-scale torsional resonator is fabricated from a lattice-matched single-crystal molecular beam epitaxy (MBE)-grown GaAs photodiode heterostructure. We find that the strain depends on the product of the electro-optic responsivity and piezoelectric constant of GaAs. The photovoltaic-piezoelectric effect has important potential applications, such as in the development of configurable optical circuits, which can be used in neuromorphic photonic chips, processing of big data with deep learning and the development of quantum circuits.

AC Conductivity and Dielectric Properties of BiScO3–PbTiO3 Piezoelectric Ceramics

2021 ◽  
Vol 13 (9) ◽  
pp. 1807-1811
Author(s):  
Jae-Hoon Ji ◽  
Yoo-Young Oh ◽  
Bo Su Kim ◽  
Wook-Hee Han ◽  
Jung-Hyuk Koh
Keyword(s):  
Dielectric Properties ◽  
Electrical Properties ◽  
Ac Conductivity ◽  
Piezoelectric Properties ◽  
Piezoelectric Materials ◽  
Ferroelectric Properties ◽  
Temperature Stability ◽  
Piezoelectric Ceramics ◽  
Dielectric Behavior ◽  
Wide Range

Bi-based BiMeO3 (where Me is a transition metal) has been extensively studied owing to its outstanding ferroelectric properties. The dielectric and electrical properties of piezoelectric ceramics can be enhanced by the addition of Bi-based materials such as BiAlO3, BiScO3 , and Bi(Mg, Ti)O3. Among them, BiScO3–PbTiO3 ceramics have shown excellent piezoelectric properties and temperature stability near the morphotropic phase boundary (MPB) region. Meanwhile, it is important to study the electrical properties of piezoelectric materials such as dielectric permittivity, conductivity of ferroelectric compounds, since dielectric and conductivities are related to pyroelectricity and piezoelectricity. In this study, the AC conductivity and dielectric properties of BiScO3–PbTiO3 ceramics were investigated with a wide range of frequencies and temperatures. Especially,the effect of PbTiO3 content on dielectric behavior of the BiScO3–PbTiO3 system was intensively studied by impedance spectroscopy.

scholarly journals Piezoelectric Energy Harvesting Solutions: A Review

Sensors ◽  
2020 ◽  
Vol 20 (12) ◽  
pp. 3512 ◽  
Author(s):  
Corina Covaci ◽  
Aurel Gontean
Keyword(s):  
Energy Harvesting ◽  
Piezoelectric Effect ◽  
Piezoelectric Transducers ◽  
Piezoelectric Energy Harvesting ◽  
Piezoelectric Energy ◽  
Direct Piezoelectric Effect ◽  
Harvesting Technique ◽  
Different Shapes ◽  
Piezoelectric Devices ◽  
Review Current

The goal of this paper is to review current methods of energy harvesting, while focusing on piezoelectric energy harvesting. The piezoelectric energy harvesting technique is based on the materials’ property of generating an electric field when a mechanical force is applied. This phenomenon is known as the direct piezoelectric effect. Piezoelectric transducers can be of different shapes and materials, making them suitable for a multitude of applications. To optimize the use of piezoelectric devices in applications, a model is needed to observe the behavior in the time and frequency domain. In addition to different aspects of piezoelectric modeling, this paper also presents several circuits used to maximize the energy harvested.

scholarly journals Tunable Crystalline Phases in UV-Curable PEG-Grafted Ladder-Structured Silsesquioxane/Polyimide Composites

Materials ◽  
2020 ◽  
Vol 13 (10) ◽  
pp. 2295 ◽  
Author(s):  
Ryung Il Kim ◽  
Ju Ho Shin ◽  
Jong Suk Lee ◽  
Jung-Hyun Lee ◽  
Albert S. Lee ◽  
...  
Keyword(s):  
Polymer Composites ◽  
Surface Properties ◽  
Weight Ratio ◽  
Hybrid Polymer ◽  
Water Contact ◽  
Uv Curable ◽  
Wide Range ◽  
Drastic Increase ◽  
Polyimide Composites ◽  
Crystalline Polyethylene

A series of UV-curable hybrid composite blends containing a carboxylic acid functionalized polyimidewith varying amounts of high molecular weight (~1 K) PEG-grafted ladder-structured polysilsesquioxanes copolymerized with methacryl groups were fabricated and their structural, thermal, mechanical, and surface properties characterized. At a composite weight ratio of polyimide above 50 wt.%, a stark shift from amorphous to crystalline polyethylene glycol (PEG) phases were observed, accompanied by a drastic increase in both surface moduli and brittleness index. Moreover, fabricated composites were shown to have a wide range water contact angle, 9.8°–73.8°, attesting to the tunable surface properties of these amphiphilic hybrid polymer composites. The enhanced mechanical properties, combined with the utility of tunable surface hydrophilicity allows for the possible use of these hybrid polymer composites to be utilized as photosensitive polyimide negative photoresists for a myriad of semiconductor patterning processes.

Note: Direct piezoelectric effect microscopy

2015 ◽  
Vol 86 (7) ◽  
pp. 076102 ◽  
Author(s):  
T. J. A. Mori ◽  
P. Stamenov ◽  
L. S. Dorneles
Keyword(s):  
Piezoelectric Effect ◽  
Direct Piezoelectric Effect

scholarly journals A Method for Quantitatively Separating the Piezoelectric Component from the as-received "Piezoelectric" Signal

2021 ◽  
Author(s):  
Chaojie Chen ◽  
Shilong Zhao ◽  
Caofeng Pan ◽  
Yunlong Zi ◽  
Fangcheng Wang ◽  
...  
Keyword(s):  
Vinylidene Fluoride ◽  
Piezoelectric Effect ◽  
Piezoelectric Materials ◽  
Contact Electrification ◽  
Poly Vinylidene Fluoride ◽  
Implantable Electronics ◽  
The Time Domain ◽  
Electric Signals ◽  
Piezoelectric Devices ◽  
Piezoelectric Performance

Abstract Polymer-based piezoelectric devices are promising for developing future wearable force sensors, nanogenerators, and implantable electronics etc. The electric signals generated by them are often assumed as solely coming from piezoelectric effect. However, triboelectric signals originated from contact electrification between the piezoelectric devices and the contacted objects can produce non-negligible interfacial electron transfer, which is often combined with the piezoelectric signal to give a triboelectric-piezoelectric hybrid output, leading to an exaggerated measured “piezoelectric” signal. Herein, a simple and effective method is proposed for quantitatively identifying and extracting the piezoelectric charge from the hybrid signal. The triboelectric and piezoelectric parts in the hybrid signal generated by a poly(vinylidene fluoride)-based device are clearly differentiated, and their force and charge characteristics in the time domain are identified. This work presents an effective method to elucidate the true piezoelectric performance in practical measurement, which is crucial for evaluating piezoelectric materials fairly and correctly.

Sign in / Sign up

Export Citation Format

Share Document