Why grinding has becoming ‘abrasive cutting’

1982 ◽  
Vol 61 (5) ◽  
pp. 45
Keyword(s):  
Abrasive Cutting

Cost of Abrasive Cutting in Decommissioning Operations in the Gulf of Mexico

2005 ◽  
Vol 131 (1) ◽  
pp. 137-148 ◽  
Author(s):  
Mark J. Kaiser ◽  
Allan G. Pulsipher ◽  
Robert C. Byrd
Keyword(s):  
Gulf Of Mexico ◽  
Abrasive Cutting

Technologies for processing materials based on glass-fiber materials

2021 ◽  
Vol 2021 (6) ◽  
pp. 24-28
Author(s):  
Kseniya Golubeva ◽  
Aleksey Noskov
Keyword(s):  
Glass Fiber ◽  
Fiber Material ◽  
Alternative Methods ◽  
Processing Methods ◽  
Characteristic Features ◽  
Fiber Materials ◽  
Abrasive Cutting

The review of basic methods for glass-fiber material machining is shown, characteristic features are presented also advantages and drawbacks of different processing methods are mentioned. There is shown a description of glass-fiber material edge machining. The alternative methods such as hydro-abrasive cutting and laser working are considered.

Ultraschallüberlagertes Trennschleifen von Faserverbundwerkstoffen*/Ultrasound abrasive cutting of fiber composites - Survey on the potential and mode of action

2016 ◽  
Vol 106 (01-02) ◽  
pp. 39-43
Author(s):  
Y. Babenko ◽  
T. Mayer ◽  
A. Gebhardt
Keyword(s):  
Surface Quality ◽  
Process Parameters ◽  
Mode Of Action ◽  
Fiber Composites ◽  
Cutting Process ◽  
Force Analysis ◽  
Abrasive Cutting

Dieser Fachartikel befasst sich mit der Untersuchung des Potentials der Ultraschallüberlagerung beim Trennschleifen moderner Faserverbundwerkstoffe. Es wurde eine Zerspankraftanalyse des Trennschleifprozesses am CFK-Werkstück mit variierenden Prozessparametern durchgeführt. Zudem wurden die Oberflächenqualitäten der Schnittkanten betrachtet.   The presented study describes the investigation of the potential of ultrasound abrasive cutting of modern fiber composites. A force analysis of the abrasive cutting process of CFRP was conducted, while the process parameters were varied. In addition, the surface quality of the machined workpieces was observed.

scholarly journals Machining of Iron-Carbon Alloys by the Use of Poly-Crystalline Diamond Cutting Inserts with Internal Cooling

2018 ◽  
Vol 2 (3) ◽  
pp. 57 ◽  
Author(s):  
Manuel Reiter ◽  
Jens Brier ◽  
Friedrich Bleicher
Keyword(s):  
Wear Behavior ◽  
Cutting Tools ◽  
Tool Material ◽  
Internal Cooling ◽  
Diamond Cutting ◽  
Diffusion Effects ◽  
Cutting Inserts ◽  
Abrasive Cutting ◽  
Poly Crystalline Diamond ◽  
Insight Into

Poly-crystalline diamond (PCD) is an extremely tough, synthetically produced cutting tool material, which offers outstanding capabilities concerning wear behavior in abrasive cutting environments. Currently, the primary application of PCD cutting tools is the machining of non-ferrous materials, as the diamond’s carbon high affinity towards iron causes diffusion effects while cutting steel with rising temperature. This effect significantly reduces tool life. To lower the occurring temperature of the cutting process, and therefore avoid the reaction of carbon and iron, a thermal functionalization of the cutting inserts has been investigated. The results give insight into making PCD cutting tools economically usable for the machining of iron-carbon materials.

scholarly journals The influence of changing the parameters of water-abrasive cutting on the quality of cutting composite cross-section structures

Mechanik ◽  
2018 ◽  
Vol 91 (7) ◽  
pp. 476-478
Author(s):  
Elżbieta Doluk ◽  
Józef Kuczmaszewski ◽  
Paweł Pieśko
Keyword(s):  
Aluminum Alloy ◽  
Surface Quality ◽  
Cross Section ◽  
Water Mass ◽  
Abrasive Water Jet ◽  
Flow Rates ◽  
Composite Layers ◽  
Mass Flow Rates ◽  
Abrasive Cutting

Presented are results of the surface quality sandwich composites (aluminum alloy EN AW-2024 and CFRP) by using an abrasive water-jet. The experiments were conducted with different speed of cutting, pressure of the abrasive water, mass flow rates, entry side of the stream and quantity of composite layers. The analysis has been studied based on received bevel angle values.

Goodness Indicator and Technological Optimization of Honing

2013 ◽  
Vol 581 ◽  
pp. 261-265 ◽  
Author(s):  
Ottó Szabó
Keyword(s):  
Material Removal ◽  
Removal Rate ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Complex Surface ◽  
Technology Planning ◽  
Technological Parameters ◽  
Machining Processes ◽  
Important Field ◽  
Abrasive Cutting

Optimisation of technological processes is an important field of research of machining processes. Honing process, its aim and results are affected more factors. Effectiveness is expressed by the following parameters: accuracy, surface roughness, complex surface quality (integrity),material removal rate, costs and productivity of the process. Developed method helps the technology planning and with the introduced new goodness indicator, investigates and corrects it. Optimization and minimization of costs can be ensured at given technological circumstances and technological parameters. With adjustment of the pressure (p) and the cutting speed (vc) economy of the process can be increased in the factory. Developed method can be applied for machining by other abrasive cutting tools. The paper summarizes new results of this theoretical and experimental research.

Abrasive Cutting Technology Deployed Via Coiled Tubing

2005 ◽  
Author(s):  
S.W. Loving ◽  
A. Ferguson ◽  
R. Hart
Keyword(s):  
Coiled Tubing ◽  
Abrasive Cutting
Sign in / Sign up

Export Citation Format

Share Document