scholarly journals A method for determining rational fluid production scale in conglomerate reservoir in the stage of high water cut

2021 ◽  
Vol 329 ◽  
pp. 01048
Author(s):  
Wentao Liu ◽  
Xiaodong Wang ◽  
Chaoliang Zhang ◽  
Rui Xue ◽  
Guifang Zhu ◽  
...  
Keyword(s):  
Formation Energy ◽  
Water Injection ◽  
Reference Value ◽  
High Water ◽  
Theoretical Research ◽  
Reservoir Water ◽  
Production Scale ◽  
Production Ratio ◽  
High Water Cut ◽  
Water Cut

In view of the problem that water cut rises quickly in conglomerate reservoirs with high water cut, based on the variation law of reservoir water injection and liquid production characteristics, a method for determining the maximum liquid production scale in conglomerate reservoirs with high water cut is established by using reservoir engineering and field statistics.Considering the maximum liquid production capacity at the well end, the maximum injection capacity at the well end and the injecting-production ratio limit to keep the formation energy, a method to determine the maximum liquid production scale in conglomerate reservoir is established to keep the formation energy sufficient.This method ensures that the injection and production ends of the reservoir are coordinated and matched, and the formation energy is sufficient, so that the reservoir development keeps a benign cycle.The research method and conclusion have important reference value and significance for theoretical research and practical application of ultra-high water cut oilfield development.

scholarly journals New Waterflooding Characteristic Curves Based on Cumulative Water Injection

2020 ◽  
Vol 2020 ◽  
pp. 1-12
Author(s):  
Zhiwang Yuan ◽  
Zhiping Li ◽  
Li Yang ◽  
Yingchun Zhang
Keyword(s):  
Characteristic Curve ◽  
Water Injection ◽  
Material Balance ◽  
Oil Production ◽  
High Water ◽  
Difficult Problem ◽  
Prediction Errors ◽  
High Water Cut Stage ◽  
High Water Cut ◽  
Water Cut

When a conventional waterflooding characteristic curve (WFCC) is used to predict cumulative oil production at a certain stage, the curve depends on the predicted water cut at the predicted cutoff point, but forecasting the water cut is very difficult. For the reservoirs whose pressure is maintained by water injection, based on the water-oil phase seepage theory and the principle of material balance, the equations relating the cumulative oil production and cumulative water injection at the moderately high water cut stage and the ultrahigh water cut stage are derived and termed the Yuan-A and Yuan-B curves, respectively. And then, we theoretically analyze the causes of the prediction errors of cumulative oil production by the Yuan-A curve and give suggestions. In addition, at the ultrahigh water cut stage, the Yuan-B water cut prediction formula is established, which can predict the water cut according to the cumulative water injection and solve the difficult problem of water cut prediction. The application results show Yuan-A and Yuan-B curves are applied to forecast oil production based on cumulative water injection data obtained by the balance of injection and production, avoiding reliance on the water cut forecast and solving the problems of predicting the cumulative oil production of producers or reservoirs that have not yet shown the decline rule. Furthermore, the formulas are simple and convenient, providing certain guiding significance for the prediction of cumulative oil production and water cut for the same reservoir types.

A Novel Multi-Layer Intelligent Test and Adjustment Technology for Water Injection Well

2012 ◽  
Vol 424-425 ◽  
pp. 732-736 ◽  
Author(s):  
De Li Jia ◽  
Feng Shan Wang ◽  
Shu Jin Zhang
Keyword(s):  
Water Injection ◽  
Dynamic Test ◽  
High Water ◽  
Adjustment Process ◽  
Flow Adjustment ◽  
High Water Cut ◽  
Water Cut ◽  
Injection Effect ◽  
Injection Technology ◽  
Clock Calibration

The layered recovery technology has been applied to the heterogeneous multi-layer standstone oilfields for many years. However, as these standstone oilfields have been entering into the ultra-high water cut period, the conventional layered water injection technology has too long test and adjustment period and heavy workload and cannot determine the reservoir condition. To solve this problem, this paper proposes and develops an intelligent multi-layer water injection technology suitable for the ultra-high water cut period based on the synchronous dynamic test and adjustment idea. The whole flow adjustment process has no any intervention and the synchronous dynamic flow adjustment of each layer finishes by the digital clock calibration thereby avoiding interlayer interference. This technology also can obtain data by the redisplay of computer. The experimental results show that this technology not only improves water injection effect and reduces the field workload, but also provides the basis of data analysis for implementation and adjustment of meticulous oil development plan

scholarly journals Experimental study on waterflooding development of low-amplitude reservoir with big bottom water

2021 ◽  
Author(s):  
Yanlai Li ◽  
Jie Tan ◽  
Songru Mou ◽  
Chunyan Liu ◽  
Dongdong Yang
Keyword(s):  
Bottom Water ◽  
Water Injection ◽  
Water Reservoir ◽  
High Water ◽  
Recovery Factor ◽  
Low Viscosity ◽  
Well Spacing ◽  
High Water Cut Stage ◽  
High Water Cut ◽  
Water Cut

AbstractFor offshore reservoirs with a big bottom water range, the water cut rises quickly and soon enters the ultra-high water cut stage. After entering the ultra-high water cut stage, due to the influence of offshore production facilities, there are few potential tapping measures, so it is urgent to explore the feasibility study of artificial water injection development. The quasi-three-dimensional and two-dimensional displacement experiments are designed using the experimental similarity criteria according to the actual reservoir parameters. Several experimental schemes are designed, fluid physical properties, interlayer distribution, and development mode according to the actual reservoir physical properties. Through the visualization of experimental equipment, the bottom water reservoir is visually stimulated. The displacement and sweep law of natural water drive and artificial water injection in bottom water reservoir with or without an interlayer, different viscosity, and different well spacing is analyzed. The following conclusions are obtained: (1) For reservoirs with a viscosity of 150 cp. The recovery factor after water injection is slightly higher than before water injection. However, the recovery factor is lower than that without injection production. The reason is that the increment of injection conversion is limited to reduce one production well after injection conversion. (2) For reservoirs with a viscosity of 30 cp. The recovery factor after injection is 39.8%, which is slightly higher than 38.9% without injection. (3) For reservoirs with a viscosity of 150 cp. In the case of the interlayer. The recovery factor after injection is 30.7%, which is significantly higher than 24.8% without injection. (4) After the well spacing of the low-viscosity reservoir is reduced, the recovery factor reaches 46.1%, which is higher than 38.9% of the non-infill scheme. After the infill well in a low-viscosity reservoir is transferred to injection, the recovery factor is 45.6%, which has little change compared with non-injection, and most of the cumulative production fluid is water. The feasibility and effect of water flooding in a strong bottom water reservoir are demonstrated. This study provides the basis for the proposal of production well injection conversion and the adjustment of production parameters in the highest water cut stage of a big bottom water reservoir.

scholarly journals Techniques for improving the water-flooding of oil fields during the high water-cut stage

2019 ◽  
Vol 74 ◽  
pp. 69 ◽  
Author(s):  
Kuiqian Ma ◽  
Ao Li ◽  
Shuhao Guo ◽  
Jieqiong Pang ◽  
Yongchao Xue ◽  
...  
Keyword(s):  
Oil Recovery ◽  
Water Injection ◽  
Reduction Rate ◽  
High Water ◽  
Water Flooding ◽  
Variable Intensity ◽  
Remaining Oil ◽  
High Water Cut Stage ◽  
High Water Cut ◽  
Water Cut

The multi-layer co-exploitation method is often used in offshore oilfields because of the large spacing between the injection and production wells. As oilfields gradually enter the high water-cut stage, the contradiction between the horizontal and vertical directions becomes more prominent, and the distribution of the remaining oil is more complex. Oilfields are facing unprecedented challenges in further enhancing oil recovery. Using oilfield A, which is in the high water-cut stage, as the research object, we compiled a detailed description of the remaining oil during the high water-cut stage using the information collected during the comprehensive adjustment and infilling of the oilfield. In addition various techniques for tapping the potential reservoir, stabilizing the oil, and controlling the water were investigated. A set of key techniques for the continuous improvement of the efficiency of water injection after comprehensive adjustment of high water-cut fields was generated. Based on the determined configuration of the offshore deltaic reservoir, a set of detailed descriptive methods and tapping technology for extracting the remaining oil in the offshore high water-cut oilfield after comprehensive adjustment was established. By considering the equilibrium displacement and using a new quantitative characterization method that includes displacement, a new technique for determining the quantity of water that needs to be injected into a stratified injection well during the high water-cut stage was established. Based on the principle of flow field intensity reconfiguration, a linear, variable-intensity, alternating injection and withdrawal technique was proposed. With the application of this series of techniques, the increase in the water content was controlled to within 1%, the natural reduction rate was controlled to within 9%, and the production increased by 1.060 × 107 m3.

On the Feasibility of Applying Electric Field to Increase Oil Recovery in Old Oil Field

2014 ◽  
Vol 900 ◽  
pp. 677-680
Author(s):  
Chun Hong Nie
Keyword(s):  
Electric Field ◽  
Oil Recovery ◽  
Water Injection ◽  
High Water ◽  
Oil Field ◽  
Thin Layers ◽  
Stable Yield ◽  
High Water Cut Stage ◽  
High Water Cut ◽  
Water Cut

This paper has discussed the characteristics, roles, feasibility and obvious effects of the technology by applying electric field to enhance oil recovery when the oil field is in high water cut stage and super high water cut stage. In view that most oil wells in old oil field have entered into the super high water cut production, the remaining oil in the main reservoir is in fragmented distribution with poor results of water injection and new reserves of oil mostly have a low penetration rate and are thin layers of poor physical properties, the use of the direct current field in period of high water cut is the best policy to achieve high and stable yield and is fairly promising.

Analysis all Kinds of Reservoir Water Degree Condition of East Xing Six District of Daqing Oilfield

2013 ◽  
Vol 868 ◽  
pp. 585-588
Author(s):  
Yi Kun Liu ◽  
Xue Ming Wang ◽  
Shi Yuan Shao ◽  
Ming Yang ◽  
Yong Ping Wang
Keyword(s):  
High Water ◽  
Oil Field ◽  
Water Flooding ◽  
Reservoir Water ◽  
Thickness Change ◽  
Degree Condition ◽  
Well Pattern ◽  
High Water Cut Stage ◽  
High Water Cut ◽  
Water Cut

East Xing Six District of Daqing oilfield development has 50 years of history, the block has entered high well density, high water cut stage. The apricot East Xing Six District demonstration zone development belongs to the continental sedimentary system, it has reservoir types and physical properties have large differences, It was long-term effected by injected water, after water flooding, water degree condition becomes very complex and unpredictable, so the washing condition analysis is an important guarantee for Daqing oilfield stable production. Using the oil field sealed coring well data, various types of reservoirs washing degree thickness change and growth are analyzed, We can know that with the further water flooding development and well pattern infilling, all kinds of oil reservoir production status; and then analyzes the potential distribution of the oilfields, and provides a basis for the development of the block and the adjustment of the next step of work, has an important guiding significance.

Research and Application of Synchronous Dynamic Test and Adjustment Technology for Novel Water Injection Well

2010 ◽  
Vol 44-47 ◽  
pp. 1476-1481 ◽  
Author(s):  
De Li Jia ◽  
Chang Jiang Zhao ◽  
Shu Jin Zhang ◽  
Ming Xin Zhao ◽  
De Kui Xu
Keyword(s):  
Water Injection ◽  
Electric Energy ◽  
Dynamic Test ◽  
High Water ◽  
High Water Cut Stage ◽  
High Water Cut ◽  
Water Cut ◽  
Injection Effect ◽  
Injection Technology ◽  
Information Test

To solve the problem that the conventional layered water injection technology has too long test and adjustment period and strong interference among layers at the ultra-high water cut stage, a novel digital synchronous dynamic test and adjustment technology is proposed and developed in this paper. Many advanced technologies, including digital multi-information test and adjustment, bidirectional transmission of remote wireless signals and non-contact electric energy transformation, are adopted to combine multi-information test and flow control to be a whole thrown into the well. This technology can automatically monitor each water injection layer and adjust water flow in user-defined period without any intervention; it can synchronously and dynamically adjust flow of each layer; and it also can monitor and adjust flow data by the redisplay of computer. The experimental results show that this technology not only reduces the field workload and improves water injection effect, but also provides the basis of data analysis for implementation and adjustment of meticulous oil development plan.

scholarly journals Thief zone identification and classification in unconsolidated sandstone reservoirs: A field case study

2021 ◽  
Author(s):  
Anzhu Xu ◽  
Fachao Shan ◽  
Xiao Yang ◽  
Jiaqi Li ◽  
Chenggang Wang ◽  
...  
Keyword(s):  
Comprehensive Evaluation ◽  
Water Injection ◽  
Fuzzy Comprehensive Evaluation ◽  
High Water ◽  
Field Development ◽  
High Water Cut ◽  
Water Cut ◽  
Bypassed Oil

AbstractChanneling between injectors and producers leads to bypassed oil left in the reservoir, which is one of most common reasons that wells in mature oil fields experience high water cut after long-term waterflooding. Identification and evaluation of the higher permeable channels (thief zones) are the key to effectively plug these thief zones and improve the conformance of water flood. This study applies three different methods to identify and evaluate the thief zones of a water injection project in North Buzazi Oilfield, a thick-bedded unconsolidated sandstone heavy oil reservoir in Manghestau, Kazakhstan. The thief zones, which evolve as a result of formation erosion and sand production, are identified and classified with respect to four different levels of significance using fuzzy comprehensive evaluation, production/injection profile method and pressure index (PI) methods. Good consistency is observed among the identification results using these methods. Finally, we present two ways to quantitatively evaluate the characteristics of the thief zones using water–oil-ratio as the input, which can be readily applied for future field development design.

Sign in / Sign up

Export Citation Format

Share Document