scholarly journals State Estimation and Determination of Flexibility Potential in Medium Voltage Networks*

2019 ◽  
Vol 217 ◽  
pp. 01013
Author(s):  
Florian Rewald ◽  
Oliver Pohl ◽  
Ulf Häger ◽  
Christian Rehtanz

This paper describes how flexibility of medium voltage systems can be used for operation of high voltage systems. This is explained using the example of a congestion management system for high voltage networks developed in the research project IDEAL. First, it is explained to what extent flexibility is required for high voltage system operation. After that, the entire congestion management system with flexibility of medium voltage systems is presented. Then, methodology for observability analysis, state estimation and determination of flexibility potential is shown. Finally, the implementation of the methodology in two real medium voltage systems is described.

2014 ◽  
Vol 494-495 ◽  
pp. 256-261
Author(s):  
Chao Zhang ◽  
Shu Mei Cui ◽  
Shi Ming Xu ◽  
Hua Feng Liu

High voltage system as power source is applied to electric school buses. In this paper, failures and potential risks of high voltage system are analyzed according to the electric school bus high voltage system configuration, and the high voltage safety management system is designed with ISO26262 as a functional safety standard. The strategies of system diagnostics and safety management are proposed to achieve the safety requirements to electric vehicles, which improve the reliability of electric vehicles and reduce the cost of maintenance.


2011 ◽  
Vol 80-81 ◽  
pp. 825-831
Author(s):  
Hai Feng Dai ◽  
Xue Zhe Wei ◽  
Ze Chang Sun ◽  
Xue Yu Chang

Vehicle safety is one of the most important design elements for all types of vehicles designed for use on public streets or roadways. Compared with traditional vehicles, besides other safety issues to be considered, a new issue that is the high voltage management problem should be taken in consideration very carefully in the electric vehicle development. This paper analyses the high voltage system in the electric vehicle and proposed a high voltage management system which implements several functions like power-up and power-down control of the high voltage system, high-voltage-circuit interlock protection, protection of electric leakage of the HV system etc. Because of the high voltage management, the electrical safety goals could be achieved and the protection of human being from high voltage hazardous becomes possible.


2018 ◽  
Vol 138 (3) ◽  
pp. 206-211
Author(s):  
Kazunori Nishimura ◽  
Yusaku Marui ◽  
Wataru Sunayama

2005 ◽  
Vol 45 (5) ◽  
pp. 575 ◽  
Author(s):  
F. D. Shaw ◽  
S. R. Baud ◽  
I. Richards ◽  
D. W. Pethick ◽  
P. J. Walker ◽  
...  

High voltage electrical stimulation applied to the lamb carcass at the end of the dressing procedure often leads to an improvement in overall product quality by reducing the incidence of toughness. It would be advantageous if the same results could be consistently achieved with the use of lower, safer, voltages — medium voltage electrical stimulation. Experiments were conducted to determine the effect of medium voltage electrical stimulation applied to wool-on carcasses on meat quality as assessed using the Sheep Meat Eating Quality protocols. A further experiment examined the interaction of electrical stimulation and meat aging time on the consumer acceptance of lamb meat. In the first experiment, 3 treatments: control (non-stimulated), medium voltage electrical stimulation (applied to the wool-on carcass) and high voltage electrical stimulation (applied at the completion of dressing) were examined. Samples of the loin (LTL) and rump (GM) muscles were evaluated by consumers using Sheep Meat Eating Quality protocols. For both muscles, the consumers gave higher scores for tenderness, juiciness, flavour and overall acceptability to the stimulated product (P<0.001). There were no statistically significant differences between the 2 stimulation treatments. The second experiment was conducted at a commercial lamb-processing abattoir that had installed a prototype automated electrode system designed to work at chain speed. Lambs received either no stimulation (control), low current medium voltage electrical stimulation (constant current 300 mA peak, 15 Hz, maximum voltage 550 V peak) or high current medium voltage electrical stimulation (constant current 600 mA peak, 15 Hz, maximum voltage 550 V peak) immediately after sticking. Electrical stimulation improved both the objective and sensory (Sheep Meat Eating Quality) eating quality attributes of lamb loin muscle when assessed following 2 days of ageing. When expressed according to consumer satisfaction rating, 30, 37 and 70% of the loins receiving low, high or no electrical stimulation, respectively, were rated as unsatisfactory at 2 days of ageing. At 4 days of ageing no loins from carcasses in the low stimulation treatment were rated by consumers to be unsatisfactory (P<0.05) compared with either non-stimulated (40%) or high-stimulated loins (35%). With respect to the effects of aging meat, electrical stimulation improved the consumer score at 2 days post-stunning by 8.9 and 4.7 points for tenderness and overall liking, respectively. Further linear improvements due to aging were similar for both electrical stimulation and unstimulated products. Under conditions of no electrical stimulation used in this experiment, 10 days aging results in tenderness and overall liking scores greater than 60 and with ES similar scores are achieved in 5 days. Consumer scores over 60 greatly reduce the chance of meat being classified as unsatisfactory.


Buildings ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 271
Author(s):  
Bruno Daniotti ◽  
Cecilia Maria Bolognesi ◽  
Sonia Lupica Spagnolo ◽  
Alberto Pavan ◽  
Martina Signorini ◽  
...  

Since the buildings and construction sector is one of the main areas responsible for energy consumption and emissions, focusing on their refurbishment and promoting actions in this direction will be helpful to achieve an EU Agenda objective of making Europe climate-neutral by 2050. One step towards the renovation action is the exploitation of digital tools into a BIM framework. The scope of the research contained in this paper is to improve the management of information throughout the different stages of the renovation process, allowing an interoperable exchange of data among the involved stakeholders; the development of an innovative BIM-based toolkit is the answer to the research question. The research and results obtained related with the development of an interoperable BIM-based toolkit for efficient renovation in buildings in the framework of the European research project BIM4EEB. Specifically, the developed BIM management system allows the exchange of the data among the different tools, using open interoperable formats (as IFC) and linked data, in a Common Data Environment, to be used by the different stakeholders. Additionally, the developed tools allow the stakeholders to manage different stages of the renovation process, facilitating efficiencies in terms of time reduction and improving the resulting quality. The validity of each tool with respect to existing practices is demonstrated here, and the strengths and weaknesses of the proposed tools are described in the workflow detailing issues such as interoperability, collaboration, integration of different solutions, and time consuming existing survey processes.


2013 ◽  
Vol 19 (S5) ◽  
pp. 58-61 ◽  
Author(s):  
Mino Yang ◽  
Jun-Ho Lee ◽  
Hee-Goo Kim ◽  
Euna Kim ◽  
Young-Nam Kwon ◽  
...  

AbstractDistribution of wax in laser printer toner was observed using an ultra-high-voltage (UHV) and a medium-voltage transmission electron microscope (TEM). As the radius of the wax spans a hundred to greater than a thousand nanometers, its three-dimensional recognition via TEM requires large depth of focus (DOF) for a volumetric specimen. A tomogram with a series of the captured images would allow the determination of their spatial distribution. In this study, bright-field (BF) images acquired with UHV-TEM at a high tilt angle prevented the construction of the tomogram. Conversely, the Z-contrast images acquired by the medium-voltage TEM produced a successful tomogram. The spatial resolution for both is discussed, illustrating that the image degradation was primarily caused by beam divergence of the Z-contrast image and the combination of DOF and chromatic aberration of the BF image from the UHV-TEM.


2020 ◽  
Vol 1679 ◽  
pp. 022045
Author(s):  
S B Rybalka ◽  
E A Kulchenkov ◽  
A A Demidov ◽  
N A Zhemoedov ◽  
A Yu Drakin ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document