scholarly journals The effect of Nb on the high strain rate hydrogen embrittlement of Q&P steel

2021 ◽  
Vol 250 ◽  
pp. 03007
Author(s):  
Florian Vercruysse ◽  
Lisa Claeys ◽  
Tom Depover ◽  
Kim Verbeken ◽  
Patricia Verleysen ◽  
...  
Keyword(s):  
Strain Rate ◽  
High Strength Steels ◽  
Thermal Desorption Spectroscopy ◽  
High Strength ◽  
Hydrogen Uptake ◽  
High Hydrogen ◽  
Damage Initiation ◽  
Advanced High Strength Steels ◽  
Dynamic Tensile Loading ◽  
Carbon Martensite

Quenching and Partitioning (Q&P) steels are, due to their excellent combination of strength and ductility, seen as good candidates for the third generation advanced high strength steels (AHSS). Although the TRIP effect is beneficial for the overall mechanical behaviour of these steels it potentially can have detrimental effects when strained in a hydrogenenriched environment. The solubility of hydrogen is high in austenite but low in high carbon martensite. Martensite is even in the absence of hydrogen already a possible damage initiation spot. The effect of hydrogen under static and dynamic tensile loading was evaluated in a Q&P and a Nb micro-alloyed Q&P steel. Experiments were carried out under a strain rate ranging from 0.03 s-1 till 500 s-1 and correlated with the hydrogen uptake characterised via thermal desorption spectroscopy (TDS). The presence of Nb resulted in a 25% increase in the hydrogen uptake capacity. A higher susceptibility to hydrogen was observed in the Nb steel partially due to the high hydrogen fraction, but also because of the larger fraction of low stability austenite. However, when tested under dynamic conditions the hydrogen susceptibility is minor and even improved in the micro-alloyed Q&P steel compared to the standard Q&P steel.

Influence of the contact with friction on the deformation behavior of advanced high strength steels in the Nakajima test

2021 ◽  
pp. 030932472110212
Author(s):  
Mohammad Mehdi Kasaei ◽  
Marta C Oliveira
Keyword(s):  
Finite Element ◽  
Friction Coefficient ◽  
Strain Rate ◽  
Contact Pressure ◽  
Deformation Behaviour ◽  
High Strength Steels ◽  
High Strength ◽  
Advanced High Strength Steels ◽  
Deformation Mechanics ◽  
Nakajima Test

This work presents a new understanding on the deformation mechanics involved in the Nakajima test, which is commonly used to determine the forming limit curve of sheet metals, and is focused on the interaction between the friction conditions and the deformation behaviour of a dual phase steel. The methodology is based on the finite element analysis of the Nakajima test, considering different values of the classic Coulomb friction coefficient, including a pressure-dependent model. The validity of the finite element model is examined through a comparison with experimental data. The results show that friction affects the location and strain path of the necking point by changing the strain rate distribution in the specimen. The strain localization alters the contact status from slip to stick at a portion of the contact area from the pole to the necking zone. This leads to the sharp increase of the strain rate at the necking point, as the punch rises further. The influence of the pressure-dependent friction coefficient on the deformation behaviour is very small, due to the uniform distribution of the contact pressure in the Nakajima test. Moreover, the low contact pressure range attained cannot properly replicate real contact condition in sheet metal forming processes of advanced high strength steels.

scholarly journals Substructure Development and Damage Initiation in a Carbide-Free Bainitic Steel upon Tensile Test

Metals ◽  
2019 ◽  
Vol 9 (12) ◽  
pp. 1261
Author(s):  
Mari Carmen Taboada ◽  
Amaia Iza-Mendia ◽  
Isabel Gutiérrez ◽  
Denis Jorge-Badiola
Keyword(s):  
Retained Austenite ◽  
High Strength Steels ◽  
High Strength ◽  
Tensile Tests ◽  
Formation Mechanisms ◽  
Tempered Martensite ◽  
Damage Initiation ◽  
Advanced High Strength Steels ◽  
Significant Strength ◽  
The Stability

Carbide-free bainitic (CFB) steels belong to the family of advanced high strength steels (AHSS) that are struggling to become part of the third-generation steels to be marketed for the automotive industry. The combined effects of the bainitic matrix and the retained austenite confers a significant strength with a remarkable ductility to these steels. However, CFB steels usually show much more complex microstructures that also contain MA (Martensite–Austenite) phase and auto-tempered martensite (ATM). These phases may compromise the ductility of CFB steels. The present work analyzes the substructure evolution during tensile tests in the necking zone, and deepens into the void and crack formation mechanisms and their relationship with the local microstructure. The combination of FEG-SEM imaging, EBSD, and X-ray diffraction has been necessary to characterize the substructure development and damage initiation. The bainite matrix has shown great ductility through the generation of high angle grain boundaries and/or large orientation gradients around voids, which are usually found close to the bainite and MA/auto-tempered martensite interfaces or fragmenting the MA phase. Special attention has been paid to the stability of the retained austenite (RA) during the test, which may eventually be transformed into martensite (Transformation Induced Plasticity, or TRIP effect).

Techniques for investigation of hydrogen embrittlement of advanced high strength steels

2018 ◽  
Vol 36 (5) ◽  
pp. 413-434 ◽  
Author(s):  
Darya Rudomilova ◽  
Tomáš Prošek ◽  
Gerald Luckeneder
Keyword(s):  
Hydrogen Embrittlement ◽  
Secondary Ion Mass Spectrometry ◽  
High Strength Steels ◽  
Thermal Desorption Spectroscopy ◽  
High Strength ◽  
Atmospheric Conditions ◽  
Kelvin Probe ◽  
Advanced High Strength Steels ◽  
Scanning Kelvin Probe ◽  
Atmospheric Exposure

AbstractProduction volumes of advanced high strength steels (AHSS) are growing rapidly due to material and energy savings they provide in a number of application areas. In order to use their potential fully, it is necessary to minimize any danger of unexpected failures caused by hydrogen embrittlement. It is possible only if deeper understanding of underlying mechanisms is obtained through further research. Besides description of main grades of AHSS and mechanisms of HE, this paper reviews available tools for determination of hydrogen content and susceptibility to HE focusing on atmospheric conditions. Techniques such as slow strain rate testing, constant load testing, electrochemical permeation technique, scanning Kelvin probe and scanning Kelvin probe force microscopy have already been used to study the effect of hydrogen entered under atmospheric exposure conditions. Nanoindentation, hydrogen microprint technique, thermal desorption spectroscopy, Ag decoration or secondary ion mass spectrometry can be also conducted after atmospheric exposure.

Advanced High Strength Steels for Automobile Body Structures

2007 ◽  
Vol 539-543 ◽  
pp. 4386-4390 ◽  
Author(s):  
M. Takahashi ◽  
A. Uenishi ◽  
H. Yoshida ◽  
H. Kuriyama
Keyword(s):  
Strain Rate ◽  
Strain Rate Sensitivity ◽  
High Strength Steels ◽  
Rate Sensitivity ◽  
High Strength ◽  
Thin Wall ◽  
Advanced High Strength Steels ◽  
Limited Length ◽  
Side Collision ◽  
Frontal Collisions

There has been a big demand for increased vehicle safety and weight reduction of auto-bodies. An extensive use of high strength steels is one of the ways to answer the requirement. Since the crashworthiness is improved by applications of higher strength steels to crashworthiness conscious structural components, various types of advanced high strength steels have been developed. The crash energy during frontal collisions is absorbed by the buckling and bending deformations of thin wall tube structures of the crushable zone of auto-bodies. In the case of side collision, on the other hand, a limited length of crushable zone requires the components to minimize the deformation during the collision. The lower the strength during press forming, the better the press formability is expected. However, the higher the strength at a collision event, the better the crashworthiness can be obtained. It can, therefore, be concluded that steels with higher strain rate sensitivities are desired. Combinations of soft ferrite phase and other hard phases were found to improve the strain rate sensitivity of flow stresses. Bake hardening is also one of the ways to improve the strain rate sensitivity of flow stresses.

Sign in / Sign up

Export Citation Format

Share Document