scholarly journals Evaluating the Influence of Polymer Modified Asphalt Binders on Low Temperature Properties

2018 ◽  
Vol 163 ◽  
pp. 05012
Author(s):  
Amal Abdelaziz ◽  
Chun-Hsing Ho ◽  
Matthew Snyder
Keyword(s):  
Low Temperature ◽  
Asphalt Concrete ◽  
Asphalt Binder ◽  
Traffic Load ◽  
Asphalt Binders ◽  
Concrete Pavements ◽  
Modified Asphalt ◽  
Modified Asphalt Binder ◽  
Low Temperature Cracking ◽  
Sbs Modified Asphalt

Low temperature cracking is one of the most common distress types in asphalt concrete pavements, particularly in cold regions. Many factors influence the behaviour of asphalt concrete pavements at low temperatures, such as the applied traffic load, environmental conditions and material characteristics. Asphalt binders are one of the primary factors that influence material properties. The purpose of this study is to compare the performance of two types of asphalt binders: styrene-butadiene-styrene (SBS) modified asphalt binder and unmodified asphalt binder in resisting low temperature cracking. The study was conducted in Flagstaff, located at the area of Northern Arizona, in the United States. Asphalt samples were collected from the paving sections and were compacted and trimmed into small beams. Bending Beam Rheometer tests were performed, using the trimmed specimens at temperatures of -6°C, -12°C and -18°C. Based on the results of the study, it was concluded that, SBS modified asphalt binder performs better in resisting low temperature cracking, compared to the unmodified binder. Based on the study outcomes, it is recommended to use SBS polymer modified polymers in areas subjected to severe cold weather events to maximize the life span of asphalt concrete pavements.

scholarly journals Evaluating the Rheological, Chemical and Morphological Properties of SBS Modified Asphalt-Binder under Multiple Aging and Rejuvenation Cycles

2021 ◽  
Vol 11 (19) ◽  
pp. 9242
Author(s):  
Xiaobing Chen ◽  
Yunfeng Ning ◽  
Yongming Gu ◽  
Ronglong Zhao ◽  
Jinhu Tong ◽  
...  
Keyword(s):  
Asphalt Binder ◽  
Morphological Properties ◽  
Asphalt Binders ◽  
Laboratory Simulation ◽  
Fatigue Properties ◽  
Type I ◽  
Modified Asphalt ◽  
Modified Asphalt Binder ◽  
Microscopic Morphology ◽  
Sbs Modified Asphalt

To investigate the influence of multiple cycles of aging and rejuvenation on the rheological, chemical, and morphological properties of styrene–butadiene–styrene (SBS)-modified asphalt-binders, the asphalt-binders were aged using two laboratory simulation methods, namely a rolling thin film oven (RTFO) test for short-term aging and pressure aging vessel (PAV) for long-term aging. The asphalt-binders were then rejuvenated with three types of rejuvenators (Type I, II, and III) with different dosages (i.e., 6%, 10%, and 14% for the first, second, and third rejuvenation, respectively). A dynamic shear rheometer (DSR) was then used to analyze the effect of rejuvenators on the rheological properties of all the asphalt-binders. The changes in the functional groups and microscopic morphology in the process of multiple aging and rejuvenation cycles were studied using Fourier transform infrared (FTIR) and atomic force microscopy (AFM). The results indicated that the three rejuvenators could soften the stiffness and restore the microstructures of the aged asphalt-binders in the process of repeated aging and rejuvenation from DSR and AFM testing. Considering the rutting and fatigue properties, the Type I rejuvenator exhibited the potential to achieve the desired rejuvenation effects under multiple rejuvenation cycles. During the multiple aging and rejuvenation cycles, the aging resistance of SBSMA decreased gradually from the FTIR results. This inherently limited the number of repeated rejuvenation cycles. This research is conducive to promoting the application of repeated penetrating rejuvenation.

scholarly journals Evaluation of Low- and Intermediate-Temperature Performance of Bio Oil-Modified Asphalt Binders

2021 ◽  
Vol 13 (7) ◽  
pp. 4039
Author(s):  
Sara A. Alattieh ◽  
Ghazi G. Al-Khateeb ◽  
Waleed Zeiada
Keyword(s):  
Low Temperature ◽  
Asphalt Binder ◽  
Fatigue Cracking ◽  
Asphalt Binders ◽  
Tensile Stresses ◽  
Modified Asphalt ◽  
Temperature Performance ◽  
Bio Oil ◽  
Low Temperature Cracking ◽  
Low Temperature Performance

Fatigue cracking and low-temperature cracking are two major distresses that occur in asphalt pavements. Fatigue cracking is a load-associated distress caused by the tensile stresses at the bottom/top of the asphalt concrete (AC) layer due to repeated traffic loading. On the other hand, low-temperature cracking occurs when tensile stresses built up with in the AC layer at low temperatures exceed the tensile strength of that layer. In this study, the performance of date seeds oil bio-modified asphalt binders (DSO-BMB) is evaluated against fatigue and low-temperature cracking. The DSO-BMBs are prepared using volume ratios of 1.5, 2.5, 3.5, 4.5, and 5.5% date seeds oil-to-asphalt binder. The base asphalt binder used in the study is a 60/70-penetration grade with a Superpave performance grade (PG) of PG 64–16. The dynamic shear rheometer (DSR) standard test was used to assess the fatigue performance of the bio-modified binders (BMBs), while the bending beam rheometer (BBR) test was used to test the BMBs for low-temperature performance. In addition, the DSR linear amplitude sweep (LAS) test was used to evaluate the fatigue tolerance behavior of the DSO-BMBs. The analysis and results of the study showed that the bio-oil enhanced the low-temperature performance. The low PG grade improved from −16 °C for the control asphalt binder to −28 °C for the BMB. Additionally, the fatigue resistance of the BMBs was improved as illustrated by the damage–characteristic curves of the modified asphalt binders from the visco-elastic continuum damage (VECD) analysis and the increase in the number of cycles to fatigue failure (Nf).

scholarly journals Impact of Graphene Oxide on Zero Shear Viscosity, Fatigue Life and Low-Temperature Properties of Asphalt Binder

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3073
Author(s):  
Abbas Mukhtar Adnan ◽  
Chaofeng Lü ◽  
Xue Luo ◽  
Jinchang Wang
Keyword(s):  
Graphene Oxide ◽  
Fatigue Life ◽  
Low Temperature ◽  
Shear Viscosity ◽  
Storage Stability ◽  
Asphalt Binder ◽  
Asphalt Binders ◽  
Test Results ◽  
Zero Shear Viscosity ◽  
Modified Asphalt

This study has investigated the impact of graphene oxide (GO) in enhancing the performance properties of an asphalt binder. The control asphalt binder (60/70 PEN) was blended with GO in contents of 0%, 0.5%, 1%, 1.5%, 2%, and 2.5%. The permanent deformation behavior of the modified asphalt binders was evaluated based on the zero shear viscosity (ZSV) parameter through a steady shear test approach. Superpave fatigue test and the linear amplitude sweep (LAS) method were used to evaluate the fatigue behavior of the binders. A bending beam rheometer (BBR) test was conducted to evaluate the low-temperature cracking behavior. Furthermore, the storage stability of the binders was investigated using a separation test. The results of the ZSV test showed that GO considerably enhanced the steady shear viscosity and ZSV value, showing a significant contribution of the GO to the deformation resistance; moreover, GO modification changed the asphalt binder’s behavior from Newtonian to shear-thinning flow. A notable improvement in fatigue life was observed with the addition of GO to the binder based on the LAS test results and Superpave fatigue parameter. The BBR test results revealed that compared to the control asphalt, the GO-modified binders showed lower creep stiffness (S) and higher creep rate (m-value), indicating increased cracking resistance at low temperatures. Finally, the GO-modified asphalt binders exhibited good storage stability under high temperatures.

scholarly journals Evaluation of Selected Performance Properties of Nanoclay-Modified Asphalt Binders

2019 ◽  
Vol 271 ◽  
pp. 03006
Author(s):  
Mohammad N. Hassan ◽  
M M Tariq Morshed ◽  
Zahid Hossain
Keyword(s):  
Colloidal Stability ◽  
Asphalt Binder ◽  
Weather Conditions ◽  
Good Alternative ◽  
Asphalt Binders ◽  
Chemical Compositions ◽  
Modified Asphalt ◽  
Adverse Weather ◽  
Modified Asphalt Binder ◽  
Improved Performance

Asphalt binders are often modified with additives such as acid, polymer, or a combination of multiple additives to achieve improved performance to sustain heavy loads and adverse weather conditions. According to some previous researches, nanoclay can be a good alternative of currently practiced Styrene-Butadiene-Styrene (SBS) modification, and the former is expected to reduce the overall cost of the asphalt binder. Three types of nanoclay (Cloisite 10A, 11B, and 15A) were blended with asphalt binders prepared from two different sources (Arabian Crude and Canadian Crude). A blending protocol has been developed to blend nanoclay with the base binders. Mechanical properties including viscosity, rutting parameter have undergone significant changes after the nanoclay modification. It was also observed that nanoclay modified binders offer different moisture susceptibility while bonding with different aggregates; the nanoclay modified asphalt binder exhibits better bonding with gravel than sandstone. Mechanistic properties such as viscosity and rutting parameter are found to be highly correlated with the chemical compositions. Binders from the Canadian crude showed more colloidal stability than binders from the Arabian crude after nanoclay modification.

scholarly journals Investigation of the Effect of Induction Heating on Asphalt Binder Aging in Steel Fibers Modified Asphalt Concrete

Materials ◽  
2019 ◽  
Vol 12 (7) ◽  
pp. 1067 ◽  
Author(s):  
Hechuan Li ◽  
Jianying Yu ◽  
Shaopeng Wu ◽  
Quantao Liu ◽  
Yuanyuan Li ◽  
...  
Keyword(s):  
Induction Heating ◽  
Asphalt Concrete ◽  
Asphalt Binder ◽  
Steel Fibers ◽  
Asphalt Binders ◽  
Carbonyl Index ◽  
Modified Asphalt ◽  
Concrete Damage ◽  
The Difference ◽  
Binder Aging

Induction heating is a valuable technology to repair asphalt concrete damage inside. However, in the process of induction heating, induced particles will release a large amount of heat to act on asphalt binder in a short time. The purpose of this paper was to study the effect of induction heating on asphalt binder aging in steel fibers modified asphalt concrete. The experiments were divided into two parts: induction heating of Dramix steel fibers coated with asphalt binder (DA) and steel wool fibers modified asphalt concrete. After induction heating, the asphalt binders in the samples were extracted for testing aging indices with Fourier Transform Infrared (FTIR), Dynamic Shear Rheometer (DSR), and Four-Components Analysis (FCA) tests. The aging of asphalt binder was analyzed identifying the change of chemical structure, the diversification of rheological properties, and the difference of component. The experiments showed that the binder inside asphalt concrete began aging during induction heating due to thermal oxygen reaction and volatilization of light components. However, there was no peak value of the carbonyl index after induction heating of ten cycles, and the carbonyl index of DA was equivalent to that of binder in asphalt concrete after three induction heating cycles, which indicated the relatively closed environment inside asphalt concrete can inhibit the occurrence of the aging reaction.

scholarly journals Cellulose Microfibril and Micronized Rubber Modified Asphalt Binder

Fibers ◽  
2021 ◽  
Vol 9 (4) ◽  
pp. 25
Author(s):  
Ang Li ◽  
Abdu A. Danladi ◽  
Rahul Vallabh ◽  
Mohammed K. Yakubu ◽  
Umar Ishiaku ◽  
...  
Keyword(s):  
Linear Regression Analysis ◽  
Asphalt Binder ◽  
Cost Effective ◽  
Cellulose Microfibrils ◽  
Asphalt Binders ◽  
Asphalt Emulsion ◽  
Clear Trend ◽  
Modified Asphalt ◽  
Weight Content ◽  
Modified Asphalt Binder

Cellulose microfibrils (CMFs) and micronized rubber powder (MRP) can be derived from low or negative-cost agricultural/industrial waste streams and offer environment-friendly and cost-effective pathways to develop engineering products. This study investigated the efficacy of adding these micromodifiers on the performance characteristics of asphalt binders. In this work, samples were produced using a mixture of slow-setting anionic asphalt emulsion with various combinations of MRP (at 0, 2 and 10 wt %) and four types of CMFs (hydrophobic and hydrophilic with crystalline ratios of 86% and 95%) at 0, 2 and 5 wt %. The performance of modified asphalt samples was assessed by penetration depth (PD), softening point (SP), and penetration index (PI). Linear regression analysis showed that adding CMFs and/or MRP reduced PD and increased SP values. The type of CMFs significantly affected the performance, which becomes more distinct with the increased weight content of CMFs. While hydrophilic CMFs caused increases in SP and PI values, no clear trend was seen to determine the effect of CMF crystallinity. It was also discovered that the combined addition of CMF and MRP achieved similar PI values at lower total weight content compared to using MRP alone.

Sign in / Sign up

Export Citation Format

Share Document