scholarly journals Diagonal reinforcement as strengthening to increase the stiffness and strength of concrete frame

2018 ◽  
Vol 195 ◽  
pp. 02033 ◽  
Author(s):  
Yenny Nurchasanah ◽  
Muhammad Ujianto ◽  
Abdul Rochman
Keyword(s):  
Structural Analysis ◽  
Opposite Direction ◽  
Lateral Loading ◽  
Structural System ◽  
Concrete Frames ◽  
Earthquake Loads ◽  
Concrete Frame ◽  
Lateral Forces ◽  
Diagonal Reinforcement ◽  
Test Objects

Two test objects of concrete frame behavior against lateral loading were performed by applying structural analysis with the wall as diagonal reinforcement in modeling. The results of the structural analysis indicated that concrete frames with walls have better performance than concrete frames without walls. Twelve objects consisting of the frame without the wall, frame with the wall, and frames with a group of steel and bamboo as diagonal reinforcement at brick walls and concrete panel walls were tested at the laboratory with monotonic lateral forces that work parallel to the wall as the illustration of earthquake loads. The diagonal reinforcement elements can spread the force received by the wall and increase the strength of the wall as well as enhance the stiffness of the structural system at once. Bracing contributes to increasing the strength, especially in resisting the compressive forces due to the earthquake loads. Deformation occurs in the opposite direction between compression path and tension path at the diagonal area. The failure in the concrete frame can be caused by the in-plane force parallel to the wall. Bamboo is quite effective to be used as a substitute for steel reinforcement as bracing material despite its shortage of steel quality.

Resistance of Reinforced Concrete Frames with Masonry Infill Walls to In-Plane Vertical Loading

2016 ◽  
Vol 711 ◽  
pp. 982-988
Author(s):  
Alex Brodsky ◽  
David Z. Yankelevsky
Keyword(s):  
Reinforced Concrete ◽  
Failure Modes ◽  
Progressive Collapse ◽  
Lateral Loading ◽  
Masonry Walls ◽  
Reinforced Concrete Frame ◽  
Masonry Infill ◽  
Concrete Frame ◽  
Vertical Loading ◽  
Infill Masonry

Numerous studies have been conducted on the in plane behavior of masonry infill walls to lateral loading simulating earthquake action on buildings. The present study is focused on a problem that has almost not been studied regarding the vertical (opposed to lateral) in-plane action on these walls. This may be of concern when a supporting column of a multi-storey reinforced concrete frame with infill masonry walls undergoes a severe damage due to an extreme loading such as a strong earthquake, car impact or military or terror action in proximity to the column. The loss of the supporting column may cause a fully or partly progressive collapse to a bare reinforced concrete frame, without infill masonry walls. The presence of the infill masonry walls may restrain the process and prevent the development of a progressive collapse. The aim of the present study is to test the in-plane composite action of Reinforced Concrete (RC) frames with infill masonry walls under vertical loading through laboratory experiments and evaluate the contributions of infill masonry walls, in an attempt to examine the infill masonry wall added resistance to the bare frame under these circumstances. Preliminary results of laboratory tests that have been conducted on reinforced concrete infilled frames without a support at their end, under monotonic vertical loading along that column axis will be presented. The observed damages and failure modes under vertical loading are clearly different from the already known failure modes observed in the case of lateral loading.

Seismic risk for commercial buildings in Memphis

1983 ◽  
Vol 73 (5) ◽  
pp. 1435-1450
Author(s):  
Andrzej S. Nowak ◽  
Elizabeth L. M. Rose
Keyword(s):  
Reinforced Concrete ◽  
Seismic Risk ◽  
Steel Structure ◽  
Structural Type ◽  
Commercial Buildings ◽  
Concrete Frames ◽  
Reinforced Concrete Frame ◽  
Damage Prediction ◽  
Concrete Frame

Abstract This paper deals with the evaluation of seismic risk for commercial buildings in Memphis, Tennessee. The seismicity of the area is summarized, and commercial buildings are divided into categories with regard to parameters such as number of stories, year of construction, assessed value, total floor area, and structural type. The distributions of these parameters are presented in the figures. During the study, over 15 buildings were examined on site by a team of experts to evaluate their seismic resistances. The quality of the design, materials, and construction was found to be surprisingly good, particularly in those structures built since 1900. Seismic resistance is analytically evaluated for five buildings: a four-story reinforced concrete frame; a four-story steel structure with vertical trusses; a 13-story stell frame; and two multi-story reinforced concrete frames. The loadings from four sources are considered: EI Centro and Taft earthquakes in California (1940 and 1952, respectively) and the forces specified in the 1979 UBC and 1981 BOCA codes. Ratios of load to capacity are calculated. For each building considered, the expected percentage of damage is evaluated for the two earthquakes. The damage prediction is extended to all commercial buildings in Memphis.

scholarly journals Effective Structural System for the Affordable Housing Construction

2018 ◽  
Vol 7 (3.2) ◽  
pp. 291
Author(s):  
Andrii Pavlikov ◽  
Serhii Mykytenko ◽  
Anton Hasenko
Keyword(s):  
Reinforced Concrete ◽  
Flat Plate ◽  
Affordable Housing ◽  
Theoretical Data ◽  
Theoretical Method ◽  
Housing Construction ◽  
Structural System ◽  
Reinforced Concrete Frame ◽  
Concrete Frame ◽  
Frame Construction

This article falls within vital question in quickly builds construction – theoretical method for calculating the slabs and columns of such buildings. Calculation research of buildings with reinforced concrete frame slabs is described in the article. The features of work the collapsible flat plate ceiling in composition of reinforced concrete framework of building are analyzed. Problems in the design of framework building are considered in order to increase its reliability. The suggestions for directions of perfection the calculation of flat plate frame construction elements are proposed in the article. The novelty of this work is to get new theoretical data about bearing capacity and deformability of structural system for the affordable housing construction from reinforced concrete.  

scholarly journals ANALISIS GAYA GEMPA PADA BANGUNAN RUMAH TINGGAL DI WILAYAH GEMPA TINGGI

2018 ◽  
Vol 7 (2) ◽  
pp. 57-64
Author(s):  
Alfian Wiranata Zebua
Keyword(s):  
Structural Analysis ◽  
Shear Force ◽  
Structure Model ◽  
Dynamic Shear ◽  
Earthquake Loads ◽  
Story Drift ◽  
Loads Analysis ◽  
Support Reactions ◽  
Static Shear

Abstract : Four stories building was used as structure model. Static earthquake loads distribution were determined according to SNI 1726:2012. The effect of dynamic earthquake loads also considered. The result of structural analysis determined using ETABS. It were static shear force 1.082,64 KN and dynamic shear force, Fx = 1.057 KN and Fy = 983,5 KN. Colomn and beam forces were also determined. Support reactions and joint displacements were determined through structural analysis. Mass modal participation has been reached over 90% at mode 5. Story drift was still smaller than the allowable story drift.Keywords : earthquake loads analysis, residential building.Abstrak:Model struktur yang dianalisis yaitu gedung beraturan lantai 4 untuk rumah tinggal. Distribusi beban gempa statik diperoleh sesuai dengan SNI 1726:2012. Pengaruh beban gempa dinamik juga diperhitungkan. Hasil analisis struktur diperoleh antara lain besaran gaya geser statik 1.082,64 KN dan gaya geser dinamik, Fx = 1.057 KN dan Fy = 983,5 KN. Besaran gaya elemen kolom dan balok juga diperoleh. Reaksi tumpuan serta perpindahan titik buhul dapat diketahui dari hasil analisis yang dilakukan. Pada mode 5, partisipasi massa model yang dianalisis sudah mencapai 90%.Simpangan antar lantai yang terjadi pada model struktur tidak melebihi simpangan yang diijinkan.Kata kunci : analisis gaya gempa, bangunan rumah tinggal.

RESISTANCE OF THE PRECAST - CAST-IN-SITU REINFORCED CONCRETE FRAMES OF CIVIL BUILDINGS UNDER SPECIAL EMERGENCY IMPACT

2021 ◽  
Vol 96 (4) ◽  
pp. 45-55
Author(s):  
P.A. KORENKOV ◽  
◽  
S.S. FEDOROV ◽  
Keyword(s):  
Thermal Protection ◽  
Progressive Collapse ◽  
Structural System ◽  
Concrete Frames ◽  
Limiting State ◽  
Space Planning ◽  
Numerical Studies ◽  
Design Loads ◽  
Multi Level

The paper obtained and analyzed the results of a numerical analysis of the survivability of a new industrial structural system of residential and public buildings that meets modern requirements for protection against progressive collapse, improved space-planning, architectural and thermal protection solutions. The presence of a significant number of enterprises with technological lines for the production of structures for large-panel housing construction and their market share, combined with a number of disadvantages of the applied technical and space-planning solutions, indicates the need to modernize these enterprises in order to produce products that meet modern requirements. The purpose of this study was to qualitatively and quantitatively study the parameters of the stress-strain state of the industrial structural system of civil buildings proposed by the authors with increased resistance to progressive collapse, the production of which would not require expensive modernization of the construction industry enterprises. On the basis of multi-level design schemes, an algorithm for calculating such a system for a special emergency effect is proposed. Numerical studies have established the compliance of the developed structural system with the requirements of a special limiting state under design loads and emergency effects caused by the sudden removal of a vertical load-bearing element.

Stabilization and Strengthening the Foundation of the Two Entrance Gates of the Holy Shrine of Imam Reza (PBUH)

2010 ◽  
Vol 133-134 ◽  
pp. 891-896
Author(s):  
Peyman Homami ◽  
Mahmood Golabchi
Keyword(s):  
Structural Analysis ◽  
Structural System ◽  
Historical Buildings ◽  
The Times ◽  
The City

This paper presents the structural analysis and constructional method for the stabilization and strengthening of the foundation of the two entrance gates in Holy Shrine of Imam Reza (PBUH). The holy shrine of Imam Reza (PBUH) is a great complex in the city of Mashhad in Iran. It was founded nearly 1000 years ago and has developed and become extensive through the times. There are several entrances and wide courts around the oldest section in the centre of the complex. Recently, the extension scopes of this complex, required excavation and construction in the basements near the two main gates, called Saat and Naghareh Khaneh Edifice. These activities, near the 400 years old edifices, needed special mobilization, like, monitoring the historical buildings and strengthening their foundations. A deep study was performed, which pursued two purposes. The first purpose was to strengthen the foundation of the buildings and the second was to make a tunnel through the foundation of the buildings because of some operational benefits for the client. At the first glance these two purposes, seemed contradictory, but finally, a new structural system for the foundation were designed and built, which was able to carry the superstructure loads to the ground while a wide tunnel was constructed as well. Special scheduled sequences of construction were prepared, which was flexible and sufficiently reliable so as to overcome any undesirable circumstances and obstacles. Monitoring the buildings behaviour during the constructional phase was conducted to assist the execution directions. This project was carried out successfully and it is in use.

The Influence of the Characteristics of the Structural System on the Results of the Calculation of High-Rise Building on Seismic Action

2018 ◽  
Vol 931 ◽  
pp. 196-199
Author(s):  
Vladimir N. Aksenov ◽  
Nikolay B. Aksenov ◽  
Muhammad V. Aushev
Keyword(s):  
Seismic Activity ◽  
Simulation Experiment ◽  
Seismic Action ◽  
Stiffness Ratio ◽  
Structural System ◽  
Reinforced Concrete Frame ◽  
Concrete Frame ◽  
High Rise ◽  
Earthquake Action ◽  
Modal Mass

This paper presents the results of the simulation experiment performed in Lira-SAPR. The purpose of the experiment is modal analysis of various structural schemes of the high-rise reinforced concrete frame under pulsation and earthquake action. Calculations have been made for three series of samples, differing in the stiffness ratio of the frame and diaphragm of the scheme (from 20% to 65.9%), considering seismic rating of 7, 8 and 9 magnitude and subsoils of the 1st, 2nd and 3rd categories of seismic activity. It has been established, that the ratio of stiffness influences the distribution of the modal mass. The acceleration of the cover nodes does not depend on the stiffness ratio – they grow as seismic activity of the site increases. Stiffness ratio influences the total reinforcement requirement. This influence is significant in the range of ratio values from 20.5% to 42.5%. Further increase in the stiffness ratio has little influence on the reinforcement requirement.

Performance of School Buildings in Turkey During the 1999 Düzce and the 2003 Bingöl Earthquakes

2009 ◽  
Vol 25 (2) ◽  
pp. 239-256 ◽  
Author(s):  
Turel Gur ◽  
AliCihan Pay ◽  
Julio A. Ramirez ◽  
Mete A. Sozen ◽  
Arvid M. Johnson ◽  
...  
Keyword(s):  
Reinforced Concrete ◽  
School Buildings ◽  
Floor Plan ◽  
Structural System ◽  
Concrete Frames ◽  
Structural Walls ◽  
Concrete Walls ◽  
Moment Resisting Frame ◽  
Moment Resisting ◽  
The Moment

Several school buildings were surveyed in the disaster areas of the Marmara (17 August 1999, [Formula: see text]), Düzce (12 November 1999, [Formula: see text]), and Bingöl (1 May 2003, [Formula: see text]) earthquakes in Turkey. Among them, 21 reinforced concrete buildings were found to have an identical floor plan. Lateral load resisting structural system consisted of reinforced concrete frames (moment-resisting frame) in 16 of the buildings and structural concrete walls integrated with the moment-resisting frame (dual system) in the remaining five buildings. The number of stories above ground in these buildings ranged from two to four. These school buildings provide a nearly ideal test of the effect of a single important structural characteristic on the performance of buildings with structural designs that are uniform in all other respects. Our observation is that the presence of structural walls improves the behavior of reinforced concrete systems drastically.

An economical structural system for wind and earthquake loads

2001 ◽  
Vol 23 (5) ◽  
pp. 491-501 ◽  
Author(s):  
T Balendra ◽  
C.H Yu ◽  
F.L Lee
Keyword(s):  
Structural System ◽  
Earthquake Loads

Nonlinear modelling and seismic behaviour of precast concrete structures with steel shear walls

2016 ◽  
Vol 49 (4) ◽  
pp. 293-304
Author(s):  
Farhad Behnamfar ◽  
Rafeek Artoonian ◽  
Mehdi Ghandil
Keyword(s):  
Precast Concrete ◽  
Shear Walls ◽  
Structural System ◽  
Concrete Frames ◽  
Seismic Behaviour ◽  
Fem Model ◽  
Shell Elements ◽  
Connection Type ◽  
Nonlinear Static ◽  
Good Agreement

A new structural system consisting of precast concrete frames and steel shear walls (SSW's) is introduced and studied numerically in this paper. Two different models, first using ''exact'' FEM and second using approximate equivalent strip model (ESM), are utilized for analysis of such a system with nonlinear static (pushover) procedure. In the FEM model use is made of shell elements while the ESM benefits from simple links that replace the wall panels in the model and are oriented such that they work in tension. Because of good agreement observed between the results of the models in smaller structures, for taller buildings only the ESM approach is followed where computationally applying the FEM approach is impractical. The lateral behaviour of the systems under consideration is investigated with regard to parameters such as number of stories and beam-column connection type. As a result, the ductility, overstrength and response modification factors are calculated for this new structural system as quantities required for their practical design.

Sign in / Sign up

Export Citation Format

Share Document