scholarly journals The study of the regularities of structure formation and properties of the L-PBF metal as a set of processes on the way to create a controlled structure

2020 ◽  
Vol 315 ◽  
pp. 13001
Author(s):  
Ivan Shakirov ◽  
Pavel Kuznetsov ◽  
Mikhail Staritsyn ◽  
Anton Zhukov ◽  
Vitaliy Bobyr
Keyword(s):  
Mechanical Properties ◽  
Structure Formation ◽  
Laser Power ◽  
Scanning Speed ◽  
Laser Powder Bed Fusion ◽  
Scanning Strategy ◽  
Powder Bed ◽  
Size And Morphology ◽  
Controlled Structure ◽  
The Relationship

In this work, to study the effect of laser powder bed fusion (L-PBF) parameters on the microstructure and mechanical properties of 321 austenitic steel, a series of samples were created combining various combinations of L-PBF technological modes, such as: laser spot diameter, scanning speed, laser power, scanning strategy. The possibility of controlling the structure formation of steel in the L-PBF process with the aim of obtaining a given crystallographic texture, grain size and morphology is estimated. The relationship between the resulting anisotropic structure and mechanical properties is investigated.

Optimization of built-part distortion in laser powder bed fusion processing of Inconel 718

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
You-Cheng Chang ◽  
Hong-Chuong Tran ◽  
Yu-Lung Lo
Keyword(s):  
Cooling Rate ◽  
Cantilever Beam ◽  
Laser Power ◽  
Scanning Speed ◽  
Processing Parameters ◽  
Laser Powder Bed Fusion ◽  
Simulation Framework ◽  
Content Type ◽  
Powder Bed ◽  
Simulation Results

Purpose Laser powder bed fusion (LPBF) provides the means to produce unique components with almost no restriction on geometry in an extremely short time. However, the high-temperature gradient and high cooling rate produced during the fabrication process result in residual stress, which may prompt part warpage, cracks or even baseplate separation. Accordingly, an appropriate selection of the LPBF processing parameters is essential to ensure the quality of the built part. This study, thus, aims to develop an integrated simulation framework consisting of a single-track heat transfer model and a modified inherent shrinkage method model for predicting the curvature of an Inconel 718 cantilever beam produced using the LPBF process. Design/methodology/approach The simulation results for the curvature of the cantilever beam are calibrated via a comparison with the experimental observations. It is shown that the calibration factor required to drive the simulation results toward the experimental measurements has the same value for all settings of the laser power and scanning speed. Representative combinations of the laser power and scanning speed are, thus, chosen using the circle packing design method and supplied as inputs to the validated simulation framework to predict the corresponding cantilever beam curvature and density. The simulation results are then used to train artificial neural network models to predict the curvature and solid cooling rate of the cantilever beam for any combination of the laser power and scanning speed within the input design space. The resulting processing maps are screened in accordance with three quality criteria, namely, the part density, the radius of curvature and the solid cooling rate, to determine the optimal processing parameters for the LPBF process. Findings It is shown that the parameters lying within the optimal region of the processing map reduce the curvature of the cantilever beam by 17.9% and improve the density by as much as 99.97%. Originality/value The present study proposes a computational framework, which could find the parameters that not only yield the lowest distortion but also produce fully dense components in the LPBF process.

scholarly journals In situ microstructure analysis of Inconel 625 during laser powder bed fusion

2021 ◽  
Author(s):  
Felix Schmeiser ◽  
Erwin Krohmer ◽  
Christian Wagner ◽  
Norbert Schell ◽  
Eckart Uhlmann ◽  
...  
Keyword(s):  
Laser Power ◽  
Scanning Speed ◽  
High Energy ◽  
Mechanical Anisotropy ◽  
Ex Situ ◽  
Inconel 625 ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Powder Bed

AbstractLaser powder bed fusion is an additive manufacturing process that employs highly focused laser radiation for selective melting of a metal powder bed. This process entails a complex heat flow and thermal management that results in characteristic, often highly textured microstructures, which lead to mechanical anisotropy. In this study, high-energy X-ray diffraction experiments were carried out to illuminate the formation and evolution of microstructural features during LPBF. The nickel-base alloy Inconel 625 was used for in situ experiments using a custom LPBF system designed for these investigations. The diffraction patterns yielded results regarding texture, lattice defects, recrystallization, and chemical segregation. A combination of high laser power and scanning speed results in a strong preferred crystallographic orientation, while low laser power and scanning speed showed no clear texture. The observation of a constant gauge volume revealed solid-state texture changes without remelting. They were related to in situ recrystallization processes caused by the repeated laser scanning. After recrystallization, the formation and growth of segregations were deduced from an increasing diffraction peak asymmetry and confirmed by ex situ scanning transmission electron microscopy. Graphical Abstract

scholarly journals Laser Powder Bed Fusion of Pure Tungsten: Effects of Process Parameters on Morphology, Densification, Microstructure

Materials ◽  
2020 ◽  
Vol 14 (1) ◽  
pp. 165
Author(s):  
Junfeng Li ◽  
Yunxiao Wu ◽  
Bokang Zhou ◽  
Zhengying Wei
Keyword(s):  
Relative Density ◽  
Laser Power ◽  
Grain Morphology ◽  
Scanning Speed ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Powder Bed ◽  
High Laser ◽  
Columnar Grains ◽  
Hatch Spacing

Tungsten has been widely used in many industrial fields due to its excellent properties. However, owing to its characteristics of inherent brittleness at room temperature and high melting point, it is difficult to prepare tungsten parts with high complexity via traditional methods. In the present work, tungsten samples were prepared by laser powder bed fusion. The influence of each process parameter including laser power, scanning speed, and hatch spacing on the surface morphology, densification, and microstructure of tungsten samples was systematically investigated. The results showed that the use of the appropriate parameters, especially high laser power, can effectively improve the surface quality and obtain a dense surface. The tungsten samples with a relative density of 98.31% were obtained with optimized parameter combinations: a laser power of 300 W, scanning speed of 400 mm/s, and hatch spacing of 0.08 mm. Compared with scanning speed and hatch spacing, the laser power had a more obvious influence on the relative density. Additionally, for the grain morphology by microstructure inspection, elongated curved grains gradually transformed into fine straight columnar grains as the scanning speed increased. The hatch spacing would change the grain morphology slightly but had no significant effect on the grain size.

scholarly journals Process–Structure–Property Relationships of Copper Parts Manufactured by Laser Powder Bed Fusion

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 2945
Author(s):  
Mohamed Abdelhafiz ◽  
Kassim S. Al-Rubaie ◽  
Ali Emadi ◽  
Mohamed A. Elbestawi
Keyword(s):  
Laser Power ◽  
Scanning Speed ◽  
Powder Bed Fusion ◽  
Structure Property ◽  
Laser Powder Bed Fusion ◽  
Powder Bed ◽  
X Ray ◽  
Structure Property Relationships ◽  
Process Structure ◽  
Hatch Spacing

The process–structure–property relationships of copper laser powder bed fusion (L-PBF)-produced parts made of high purity copper powder (99.9 wt %) are examined in this work. A nominal laser beam diameter of 100 μm with a continuous wavelength of 1080 nm was employed. A wide range of process parameters was considered in this study, including five levels of laser power in the range of 200 to 370 W, nine levels of scanning speed from 200 to 700 mm/s, six levels of hatch spacing from 50 to 150 μm, and two layer thickness values of 30 μm and 40 μm. The influence of preheating was also investigated. A maximum relative density of 96% was obtained at a laser power of 370 W, scanning speed of 500 mm/s, and hatch spacing of 100 μm. The results illustrated the significant influence of some parameters such as laser power and hatch spacing on the part quality. In addition, surface integrity was evaluated by surface roughness measurements, where the optimum Ra was measured at 8 μm ± 0.5 μm. X-ray photoelectron spectroscopy (XPS) and energy-dispersive X-ray spectroscopy (EDX) were performed on the as-built samples to assess the impact of impurities on the L-PBF part characteristics. The highest electrical conductivity recorded for the optimum density-low contaminated coils was 81% IACS.

Investigation of mechanical properties and microstructures of GH536 fabricated by laser powder bed fusion additive manufacturing

2020 ◽  
Vol 235 (1-2) ◽  
pp. 155-165
Author(s):  
Yunpeng Ren ◽  
Heng Lu ◽  
Dongyang Xu ◽  
Yan Chen ◽  
Zhiduo Xin ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Additive Manufacturing ◽  
Relative Density ◽  
Laser Energy ◽  
Hot Forging ◽  
Scanning Speed ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Powder Bed

Laser powder bed fusion additive manufacturing of superalloys has received increasing attention in these years. In this article, the influence of parameters of laser powder bed fusion on mechanical properties and microstructures of nickel-based superalloy GH536 was investigated. Influence of laser power, scanning speed, hatch space and building direction on mechanical properties was discussed, and the optimal parameters were obtained. The relative density of samples fabricated by laser powder bed fusion could be as high as 99.5%. The processing window of laser energy density with 8.56 × 104–1.15 × 105 J/cm3 should be employed to make sure that the relative density is higher than 98%. The ultimate tensile strength and yield stress of GH536 sample made by laser powder bed fusion were 950 and 606 MPa, respectively, which were superior to samples with the tensile strength of 767 MPa and yield strength of 379 MPa prepared by traditional hot forging method. The hardness of the sample could reach 316.8 HV.

Sign in / Sign up

Export Citation Format

Share Document