scholarly journals The modified early age strains development model for the case of two-way restraint conditions

2021 ◽  
Vol 350 ◽  
pp. 00010
Author(s):  
Volha Sannikava ◽  
Viktar Tur
Keyword(s):  
Analytical Model ◽  
Experimental Results ◽  
Development Model ◽  
Early Age ◽  
Plastic Behavior ◽  
Stress Strain ◽  
Expansive Concrete ◽  
Proposed Model ◽  
Concrete Elements ◽  
Expansion Period

This paper proposes a design model (2D MSDM) for assessment the early-age stress-strain parameters of two-axially restrained expansive concrete elements. The analytical model allows defining the restrained expansion strains and corresponding self-stresses in case of arbitrary restraint conditions in orthogonal directions by taking into consideration the elastic-plastic behavior of concrete during the expansion period. The results of solution according to the proposed model were compared with the experimental results of expansive concrete elements with orthogonal confinement carried out by authors and other researchers.

scholarly journals Assessment of the early-age strains and stresses in 2D restrained self-stressed members

2020 ◽  
Vol 19 (4) ◽  
pp. 085-094
Author(s):  
Viktar V. Tur ◽  
Volha H. Sannikava
Keyword(s):  
Analytical Approach ◽  
Experimental Results ◽  
Development Model ◽  
Early Age ◽  
Steel Tubes ◽  
Mesh Reinforcement ◽  
Centre Of Gravity ◽  
Expansive Concrete ◽  
Iterative Procedures ◽  
Concrete Filled Steel Tubes

The paper presents the implementation of the modified strains development model (MSDM) for the two-way restrained self-stressed members such as expansive concrete-filled steel tubes and expansive concrete plane elements with arbitrary orthogonal reinforcement. The analytical approach allows defining the restrained strains and stresses in any 2D restraint conditions by following the iterative procedures and accounting for the elastic-plastic behaviour of expansive concrete at an early age. The consistency of the proposed method was confirmed by assessing the experimental results of the two series of the expansive concrete-filled steel tubes and three series of the expansive concrete plane members with mesh reinforcement in the centre of gravity.

scholarly journals Analytical Model for Restraint Strains and Self-stressed in Expansive Concrete Filled Steel Tubes (ECFST) estimation

2020 ◽  
pp. 93-98
Author(s):  
Viktar V. Tur ◽  
Radoslaw Duda ◽  
Dina Khmaruk ◽  
Viktar Basav
Keyword(s):  
Experimental Data ◽  
Experimental Studies ◽  
Steel Tube ◽  
Development Model ◽  
Steel Tubes ◽  
Concrete Core ◽  
Expansive Concrete ◽  
Proposed Model ◽  
Comparison Results ◽  
Concrete Filled Steel Tubes

In this paper, a modified strains development model (MSDM) for expansive concrete-filled steel tube (ECFST) was formulated and verified on the experimental data, obtained from testing specimens on the expansion stage. The modified strain development model for restraint strains and self-stresses values estimation in concrete with high expansion energy capacity under any type of the symmetrical and unsymmetrical finite stiffness restraint conditions was proposed. Based on proposed MSDM a new model for expansive concrete-filled steel tubes is developed. The main difference between this model and other previously developed models consists in taking into account in the basic equations an induced force in restrain that is considered as an external load applied to the concrete core of the member. For verification of the proposed model-specific experimental studies were performed. As follows from comparison results restrained expansion strains values calculated following the proposed model shows good compliance with experimental data. The values predicted by the proposed MSDM for concrete-filled steel and obtained experimental data demonstrated good agreement that confirms the validity of the former.

Analytical and Numerical Modelling of Sheet Plate Cold Expanded Hole Subjected to Reverse Yielding

2019 ◽  
Author(s):  
Abdel-Hakim Bouzid ◽  
Hacène Touahri
Keyword(s):  
Aluminum Alloy ◽  
Residual Stresses ◽  
Strain Hardening ◽  
Analytical Model ◽  
Life Assessment ◽  
Thick Wall ◽  
Plastic Behavior ◽  
Alloy Plate ◽  
Proposed Model ◽  
Reverse Yielding

Abstract Predicting and mitigating the effect of expansion induced by cold working on damage fatigue accumulation and life assessment of aluminum alloy is a common process in the aeronautics industry, especially to extend the fatigue lifetime of their structures. This process aims at generating residual stresses and increases thereby the strength of hollow parts including aluminum alloy plate holes that are employed in manufacturing the airplane fuselage. An analytical model to predict the residual stresses induced during the expansion process due to the cold strain hardening is developed. The proposed model is based on an elasto-plastic behavior, with a power law material behaviour and relies on the theory of autofrettaged thick wall cylinders in plane strain state to which reverse yielding is incorporated. The application of Hencky theory of plastic deformation is used in the analytical calculations of the stresses and strains. Finite-element numerical simulation is used to validate the developed analytical model by comparison of the radial, Hoop, longitudinal and equivalent stresses for both the loading and unloading phases. The obtained results show clearly that the level of residual stresses depends mainly on the interference and strain hardening while reverse yielding reduce the stresses near the hole.

scholarly journals Analytical model of carrier mobility in a Polymer Field Effect Transistor

2007 ◽  
Vol 61 (2) ◽  
pp. 55-59
Author(s):  
Milan Milosevic ◽  
Rifat Ramovic
Keyword(s):  
Analytical Model ◽  
Field Effect ◽  
Carrier Mobility ◽  
Field Effect Transistor ◽  
Experimental Results ◽  
Transistor Channel ◽  
Proposed Model ◽  
Current Voltage ◽  
Effect Transistor ◽  
Parameters Of Interest

In this paper, the carrier mobility analytical model in a POFET (Polymer Field Effect Transistor) channel is proposed. The model was developed on the basis of existing models and experimental results. The proposed model is universal because it encompasses the carrier mobility dependence on temperature, electric field and trap density in the POFET channel. The model is comparatively simple, easy for application and gives valuable results. According to the presented model, simulations of mobility as a function of the parameters of interest were performed. The obtained results are shown graphically. In comparison to accessible experimental results excellent correspondence was found. This model enables the calculation of simple POFET current-voltage I (V) characteristics.

Delamination in the scoring and folding of paperboard

TAPPI Journal ◽  
2012 ◽  
Vol 11 (1) ◽  
pp. 61-66 ◽  
Author(s):  
DOEUNG D. CHOI ◽  
SERGIY A. LAVRYKOV ◽  
BANDARU V. RAMARAO
Keyword(s):  
Finite Element ◽  
Plane Deformation ◽  
Strain Analysis ◽  
Local Strain ◽  
Uniaxial Stress ◽  
Material Model ◽  
Element Model ◽  
Plastic Behavior ◽  
Stress Strain ◽  
Strain Fields

Delamination between layers occurs during the creasing and subsequent folding of paperboard. Delamination is necessary to provide some stiffness properties, but excessive or uncontrolled delamination can weaken the fold, and therefore needs to be controlled. An understanding of the mechanics of delamination is predicated upon the availability of reliable and properly calibrated simulation tools to predict experimental observations. This paper describes a finite element simulation of paper mechanics applied to the scoring and folding of multi-ply carton board. Our goal was to provide an understanding of the mechanics of these operations and the proper models of elastic and plastic behavior of the material that enable us to simulate the deformation and delamination behavior. Our material model accounted for plasticity and sheet anisotropy in the in-plane and z-direction (ZD) dimensions. We used different ZD stress-strain curves during loading and unloading. Material parameters for in-plane deformation were obtained by fitting uniaxial stress-strain data to Ramberg-Osgood plasticity models and the ZD deformation was modeled using a modified power law. Two-dimensional strain fields resulting from loading board typical of a scoring operation were calculated. The strain field was symmetric in the initial stages, but increasing deformation led to asymmetry and heterogeneity. These regions were precursors to delamination and failure. Delamination of the layers occurred in regions of significant shear strain and resulted primarily from the development of large plastic strains. The model predictions were confirmed by experimental observation of the local strain fields using visual microscopy and linear image strain analysis. The finite element model predicted sheet delamination matching the patterns and effects that were observed in experiments.

Connected-Tube MPP Model for Unsupervised 3D Fiber Detection

2020 ◽  
Vol 2020 (14) ◽  
pp. 305-1-305-6
Author(s):  
Tianyu Li ◽  
Camilo G. Aguilar ◽  
Ronald F. Agyei ◽  
Imad A. Hanhan ◽  
Michael D. Sangid ◽  
...  
Keyword(s):  
Composite Material ◽  
Point Process ◽  
Marked Point ◽  
Experimental Results ◽  
Marked Point Process ◽  
Fiber Reinforced Composite ◽  
Reinforced Composite ◽  
Proposed Model ◽  
Cylinder Model ◽  
Reinforced Composite Material

In this paper, we extend our previous 2D connected-tube marked point process (MPP) model to a 3D connected-tube MPP model for fiber detection. In the 3D case, a tube is represented by a cylinder model with two spherical areas at its ends. The spherical area is used to define connection priors that encourage connection of tubes that belong to the same fiber. Since each long fiber can be fitted by a series of connected short tubes, the proposed model is capable of detecting curved long tubes. We present experimental results on fiber-reinforced composite material images to show the performance of our method.

scholarly journals Early-Age Tensile Bond Characteristics of Epoxy Coatings for Underwater Applications

Coatings ◽  
2019 ◽  
Vol 9 (11) ◽  
pp. 757 ◽  
Author(s):  
Kim ◽  
Hong ◽  
Han ◽  
Kim
Keyword(s):  
Bond Strength ◽  
Surface Treatment ◽  
Epoxy Resin ◽  
Coating Thickness ◽  
Experimental Results ◽  
Early Age ◽  
Curing Time ◽  
Bond Performance ◽  
Coating Type ◽  
Bond Characteristics

In this study, coating equipment for the effective underwater repair of submerged structures was developed. The tensile bond characteristics of selected epoxy resin coatings were investigated by coating the surface of a specimen using each of the four types of equipment. Using the experimental results, the tensile bond strength and the coating thickness were analyzed according to the type of equipment, coating, and curing time. The results show that the type of coating equipment used had the greatest effect on the measured bond strength and coating thickness of the selected coatings. However, the effect of coating type and curing time on the bond strength and the thickness was observed to be insignificant. Compared with the developed equipment, the surface treatment of the coating was observed to be more effective when using the pre-existing equipment, and thus the bond performance of the coating was improved compared to using the pre-existing equipment. Based on the experimental results, improvements and needs involving the equipment for further research were discussed.

scholarly journals Generalized analytical model based on harmonic coupling for hybrid plasmonic modes: comparison with numerical and experimental results

2015 ◽  
Vol 23 (21) ◽  
pp. 27376 ◽  
Author(s):  
Mitradeep Sarkar ◽  
Jean-François Bryche ◽  
Julien Moreau ◽  
Mondher Besbes ◽  
Grégory Barbillon ◽  
...  
Keyword(s):  
Analytical Model ◽  
Experimental Results ◽  
Model Based

scholarly journals A General Temperature-Dependent Stress–Strain Constitutive Model for Polymer-Bonded Composite Materials

Polymers ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1393
Author(s):  
Xiaochang Duan ◽  
Hongwei Yuan ◽  
Wei Tang ◽  
Jingjing He ◽  
Xuefei Guan
Keyword(s):  
Composite Materials ◽  
Constitutive Model ◽  
Model Parameters ◽  
Temperature Dependent ◽  
Stress Strain ◽  
Proposed Model ◽  
Single Temperature ◽  
Testing Data ◽  
Bonded Composite ◽  
Tension And Compression

This study develops a general temperature-dependent stress–strain constitutive model for polymer-bonded composite materials, allowing for the prediction of deformation behaviors under tension and compression in the testing temperature range. Laboratory testing of the material specimens in uniaxial tension and compression at multiple temperatures ranging from −40 ∘C to 75 ∘C is performed. The testing data reveal that the stress–strain response can be divided into two general regimes, namely, a short elastic part followed by the plastic part; therefore, the Ramberg–Osgood relationship is proposed to build the stress–strain constitutive model at a single temperature. By correlating the model parameters with the corresponding temperature using a response surface, a general temperature-dependent stress–strain constitutive model is established. The effectiveness and accuracy of the proposed model are validated using several independent sets of testing data and third-party data. The performance of the proposed model is compared with an existing reference model. The validation and comparison results show that the proposed model has a lower number of parameters and yields smaller relative errors. The proposed constitutive model is further implemented as a user material routine in a finite element package. A simple structural example using the developed user material is presented and its accuracy is verified.

Convective Losses From Cavity Solar Receivers—Comparisons Between Analytical Predictions and Experimental Results

1983 ◽  
Vol 105 (1) ◽  
pp. 29-33 ◽  
Author(s):  
A. M. Clausing
Keyword(s):  
Experimental Data ◽  
Experimental Evidence ◽  
Analytical Model ◽  
Excellent Agreement ◽  
Experimental Results ◽  
Simple Analytical Model ◽  
Refined Model ◽  
Wall Area

Cavity solar receivers are generally believed to have higher thermal efficiencies than external receivers due to reduced losses. A simple analytical model was presented by the author which indicated that the ability to heat the air inside the cavity often controls the convective loss from cavity receivers. Thus, if the receiver contains a large amount of inactive hot wall area, it can experience a large convective loss. Excellent experimental data from a variety of cavity configurations and orientations have recently become available. These data provided a means of testing and refining the analytical model. In this manuscript, a brief description of the refined model is presented. Emphasis is placed on using available experimental evidence to substantiate the hypothesized mechanisms and assumptions. Detailed comparisons are given between analytical predictions and experimental results. Excellent agreement is obtained, and the important mechanisms are more clearly delineated.

Sign in / Sign up

Export Citation Format

Share Document