scholarly journals Three-Dimensional Network Adjustment of Laser Tracker Measurements for Large-Scale Metrology Applications

2021 ◽  
Vol 147 (1) ◽  
pp. 05020009
Author(s):  
Peter E. Manwiller
Keyword(s):  
Large Scale ◽  
Three Dimensional ◽  
Laser Tracker ◽  
Network Adjustment ◽  
Dimensional Network

scholarly journals A Review of Reactor Designs for Hydrogen Storage in Clathrate Hydrates

2021 ◽  
Vol 11 (2) ◽  
pp. 469
Author(s):  
Mohammad Reza Ghaani ◽  
Judith M. Schicks ◽  
Niall J. English
Keyword(s):  
Hydrogen Storage ◽  
Large Scale ◽  
Three Dimensional ◽  
Pilot Scale ◽  
Clathrate Hydrates ◽  
Dimensional Network ◽  
Future Challenges ◽  
Industrial Use ◽  
Pilot Scale Reactor ◽  
And Storage

Clathrate hydrates are ice-like, crystalline solids, composed of a three-dimensional network of hydrogen bonded water molecules that confines gas molecules in well-defined cavities that can store gases as a solid solution. Ideally, hydrogen hydrates can store hydrogen with a maximum theoretical capacity of about 5.4 wt%. However, the pressures necessary for the formation of such a hydrogen hydrate are 180–220 MPa and therefore too high for large-scale plants and industrial use. Thus, since the early 1990s, there have been numerous studies to optimize pressure and temperature conditions for hydrogen formation and storage and to develop a proper reactor type via optimisation of the heat and mass transfer to maximise hydrate storage capacity in the resulting hydrate phase. So far, the construction of the reactor has been developed for small, sub-litre scale; and indeed, many attempts were reported for pilot-scale reactor design, on the multiple-litre scale and larger. The purpose of this review article is to compile and summarise this knowledge in a single article and to highlight hydrogen-storage prospects and future challenges.

Development of Mucoadhesive Buccal Drug Delivery System of Propranolol Hydrochloride Using Aster ericoides Mucilage

2020 ◽  
Vol 10 (2) ◽  
pp. 133-148
Author(s):  
Ankaj Kaundal ◽  
Pravin Kumar ◽  
Rajendra Awasthi ◽  
Giriraj T. Kulkarni
Keyword(s):  
Buccal Cavity ◽  
Three Dimensional ◽  
Hot Water ◽  
Fickian Diffusion ◽  
Aster Ericoides ◽  
Dimensional Network ◽  
Buccal Tablet ◽  
Significant Difference ◽  
Volunteer Group

Aim: The study was aimed to develop mucoadhesive buccal tablets using Aster ericoides leaves mucilage. Background : Mucilages are naturally occurring high-molecular-weight polyuronides, which have been extensively studied for their application in different pharmaceutical dosage forms. Objective: The objective of the present research was to establish the mucilage isolated from the leaves of Aster ericoides as an excipient for the formulation of the mucoadhesive buccal tablet. Method: The mucilage was isolated from the leaves of Aster ericoides by maceration, precipitated with acetone and characterized. Tablets were prepared using wet granulation technique and evaluated for various official tests. Results: The mucilage was found to be non-toxic on A-431 and Vero cell lines. It was insoluble but swellable in cold and hot water. The results indicate that mucilage can form a three-dimensional network. The pH of the mucilage (6.82 ± 0.13) indicated that it might be non-irritant to the buccal cavity. The mucilage was found to be free from microbes. The release of drug was by Fickian diffusion. The in vivo buccal tablet acceptance was 80%. No significant difference between the diastolic blood pressure of standard and Aster tablets treated volunteer group was recorded. Conclusion: The mucilage was found to be non-toxic on A-431 and Vero cell lines. It was insoluble but swellable in cold and hot water. The results indicate that mucilage can form a three-dimensional network. The pH of the mucilage (6.82 ± 0.13) indicated that it might be non-irritant to the buccal cavity. The mucilage was found to be free from microbes. The release of drug was by Fickian diffusion. The in vivo buccal tablet acceptance was 80%. No significant difference between the diastolic blood pressure of standard and Aster tablets treated volunteer group was recorded. Other: However, to prove the potency of the polymer, in vivo bioavailability studies in human volunteers are needed along with chronic toxicity studies in suitable animal models.

scholarly journals Crystal structure of K[Hg(SCN)3] – a redetermination

2014 ◽  
Vol 70 (9) ◽  
pp. i46-i46 ◽  
Author(s):  
Matthias Weil ◽  
Thomas Häusler
Keyword(s):  
Crystal Structure ◽  
Room Temperature ◽  
Three Dimensional ◽  
Lattice Parameters ◽  
Bond Lengths ◽  
Dimensional Network ◽  
Anisotropic Displacement Parameters ◽  
Precision And Accuracy ◽  
Standard Deviations ◽  
Atomic Coordinates

The crystal structure of the room-temperature modification of K[Hg(SCN)3], potassium trithiocyanatomercurate(II), was redetermined based on modern CCD data. In comparison with the previous report [Zhdanov & Sanadze (1952).Zh. Fiz. Khim.26, 469–478], reliability factors, standard deviations of lattice parameters and atomic coordinates, as well as anisotropic displacement parameters, were revealed for all atoms. The higher precision and accuracy of the model is, for example, reflected by the Hg—S bond lengths of 2.3954 (11), 2.4481 (8) and 2.7653 (6) Å in comparison with values of 2.24, 2.43 and 2.77 Å. All atoms in the crystal structure are located on mirror planes. The Hg2+cation is surrounded by four S atoms in a seesaw shape [S—Hg—S angles range from 94.65 (2) to 154.06 (3)°]. The HgS4polyhedra share a common S atom, building up chains extending parallel to [010]. All S atoms of the resulting1∞[HgS2/1S2/2] chains are also part of SCN−anions that link these chains with the K+cations into a three-dimensional network. The K—N bond lengths of the distorted KN7polyhedra lie between 2.926 (2) and 3.051 (3) Å.

scholarly journals Construction of the Cellulose Nanofibers (CNFs) Aerogel Loading TiO2 NPs and Its Application in Disposal of Organic Pollutants

Polymers ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1841
Author(s):  
Kang Li ◽  
Xuejie Zhang ◽  
Yan Qin ◽  
Ying Li
Keyword(s):  
High Efficiency ◽  
Sol Gel ◽  
Cellulose Nanofibers ◽  
Three Dimensional ◽  
Good Mechanical Property ◽  
Polar Groups ◽  
Dimensional Network ◽  
Natural Polysaccharide ◽  
Valuable Method ◽  
Adsorption Capability

Aerogels have been widely used in the adsorption of pollutants because of their large specific surface area. As an environmentally friendly natural polysaccharide, cellulose is a good candidate for the preparation of aerogels due to its wide sources and abundant polar groups. In this paper, an approach to construct cellulose nanofibers aerogels with both the good mechanical property and the high pollutants adsorption capability through chemical crosslinking was explored. On this basis, TiO2 nanoparticles were loaded on the aerogel through the sol-gel method followed by the hydrothermal method, thereby the enriched pollutants in the aerogel could be degraded synchronously. The chemical cross-linker not only helps build the three-dimensional network structure of aerogels, but also provides loading sites for TiO2. The degradation efficiency of pollutants by the TiO2@CNF Aerogel can reach more than 90% after 4 h, and the efficiency is still more than 70% after five cycles. The prepared TiO2@CNF Aerogels have high potential in the field of environmental management, because of the high efficiency of treating organic pollutes and the sustainability of the materials. The work also provides a choice for the functional utilization of cellulose, offering a valuable method to utilize the large amount of cellulose in nature.

scholarly journals A Review on Additive Manufacturing Possibilities for Electrical Machines

Energies ◽  
2021 ◽  
Vol 14 (7) ◽  
pp. 1940
Author(s):  
Muhammad Usman Naseer ◽  
Ants Kallaste ◽  
Bilal Asad ◽  
Toomas Vaimann ◽  
Anton Rassõlkin
Keyword(s):  
Additive Manufacturing ◽  
Large Scale ◽  
Three Dimensional ◽  
Electrical Machines ◽  
Electromagnetic Properties ◽  
Scale Production ◽  
Performance Parameters ◽  
Large Scale Production ◽  
One Step ◽  
Manufacturing Techniques

This paper presents current research trends and prospects of utilizing additive manufacturing (AM) techniques to manufacture electrical machines. Modern-day machine applications require extraordinary performance parameters such as high power-density, integrated functionalities, improved thermal, mechanical & electromagnetic properties. AM offers a higher degree of design flexibility to achieve these performance parameters, which is impossible to realize through conventional manufacturing techniques. AM has a lot to offer in every aspect of machine fabrication, such that from size/weight reduction to the realization of complex geometric designs. However, some practical limitations of existing AM techniques restrict their utilization in large scale production industry. The introduction of three-dimensional asymmetry in machine design is an aspect that can be exploited most with the prevalent level of research in AM. In order to take one step further towards the enablement of large-scale production of AM-built electrical machines, this paper also discusses some machine types which can best utilize existing developments in the field of AM.

scholarly journals Vibration characteristics of triple-gear-rotor system in compressed air energy storage under variable torque load

2021 ◽  
Vol 104 (1) ◽  
pp. 003685042098705
Author(s):  
Xinran Wang ◽  
Yangli Zhu ◽  
Wen Li ◽  
Dongxu Hu ◽  
Xuehui Zhang ◽  
...  
Keyword(s):  
Large Scale ◽  
Three Dimensional ◽  
Element Model ◽  
Rotor System ◽  
Dynamic Responses ◽  
System Response ◽  
Rotating Speed ◽  
Torque Load ◽  
Set Up ◽  
Two Stages

This paper focuses on the effects of the off-design operation of CAES on the dynamic characteristics of the triple-gear-rotor system. A finite element model of the system is set up with unbalanced excitations, torque load excitations, and backlash which lead to variations of tooth contact status. An experiment is carried out to verify the accuracy of the mathematical model. The results show that when the system is subjected to large-scale torque load lifting at a high rotating speed, it has two stages of relatively strong periodicity when the torque load is light, and of chaotic when the torque load is heavy, with the transition between the two states being relatively quick and violent. The analysis of the three-dimensional acceleration spectrum and the meshing force shows that the variation in the meshing state and the fluctuation of the meshing force is the basic reasons for the variation in the system response with the torque load. In addition, the three rotors in the triple-gear-rotor system studied show a strong similarity in the meshing states and meshing force fluctuations, which result in the similarity in the dynamic responses of the three rotors.

Sign in / Sign up

Export Citation Format

Share Document