Synthesis, characterization of LCMO composite and fabrication of its thin films by R.F magnetron sputtering for room-temperature applications

2020 ◽  
Author(s):  
Navjyoti Boora ◽  
Poonam Rani ◽  
Vandana Nagal ◽  
Shafaque Rahman ◽  
V. P. S Awana ◽  
...  
Keyword(s):  
Thin Films ◽  
Magnetron Sputtering ◽  
Room Temperature ◽  
Temperature Applications

Structural Evolution Upon Annealing of Multi-Layer Si/Fe Thin Films Prepared by Magnetron Sputtering

2007 ◽  
Vol 561-565 ◽  
pp. 1161-1164
Author(s):  
Xiao Na Li ◽  
Bing Hu ◽  
Chuang Dong ◽  
Xin Jiang
Keyword(s):  
Thin Films ◽  
Magnetron Sputtering ◽  
Room Temperature ◽  
Structural Evolution ◽  
Radio Frequency Magnetron Sputtering ◽  
Transmission Electron ◽  
Direct Band ◽  
The Stability ◽  
Sputtering System

Fe/Si multi-layer films were fabricated on Si (100) substrates utilizing radio frequency magnetron sputtering system. Si/β-FeSi2 structure was found in the films after the deposition. Structural characterization of Fe-silicide sample was performed by transmission electron microscopy, to explore the dependence of the microstructure of β-FeSi2 film on the preparation parameters. It was found that β-FeSi2 particles were formed after the deposition without annealing, whose size is less than 20nm ,with a direct band-gap of 0.94eV in room temperature. After annealing at 850°C, particles grow lager, however the stability of thin films was still good.

Silicon Germanium Oxide (SixGeyO1-x-y) Infrared Sensitive Material for Uncooled Detectors

2010 ◽  
Vol 1245 ◽  
Author(s):  
Reza Anvari ◽  
Qi Cheng ◽  
Muhammad Lutful Hai ◽  
Truc Phan Bui ◽  
A. J. Syllaios ◽  
...  
Keyword(s):  
Thin Films ◽  
Electrical Properties ◽  
Magnetron Sputtering ◽  
Silicon Germanium ◽  
Room Temperature ◽  
Rf Magnetron Sputtering ◽  
Germanium Oxide ◽  
Temperature Coefficient Of Resistance ◽  
Sensitive Material

AbstractThis paper presents the formation and the characterization of silicon germanium oxide (SixGeyO1-x-y) infrared sensitive material for uncooled microbolometers. RF magnetron sputtering was used to simultaneously deposit Si and Ge thin films in an Ar/O2 environment at room temperature. The effects of varying Si and O composition on the thin film's electrical properties which include temperature coefficient of resistance (TCR) and resistivity were investigated. The highest achieved TCR and the corresponding resistivity at room temperature were -5.41 %/K and 3.16×103 ohm cm using Si0.039Ge0.875O0.086 for films deposited at room temperature.

Growth and Characterization of Thermoelectric Mg2Si Thin Films

2011 ◽  
Vol 1325 ◽  
Author(s):  
Thomas C. Hasapis ◽  
Eleni C. Stefanaki ◽  
Anastasios Siozios ◽  
Euripides Hatzikraniotis ◽  
George Vourlias ◽  
...  
Keyword(s):  
Thin Films ◽  
Magnetron Sputtering ◽  
Room Temperature ◽  
Si Substrate ◽  
Sputtering Power

ABSTRACTIn this work, room temperature co-deposition of Mg and Si was used to successfully fabricate Mg2Si thin films on Si substrate by dual cathode magnetron sputtering (DCMS). Films were annealed at 380°C. Various Mg/Si sputtering power ratios have been examined. XRD, SEM and IR reflectivity measurements on grown and annealed films, reveal that annealing is enhancing the formation of crystalline Mg2Si.

Characterization of Rutile N-Doped TiO2 Films Prepared by RF Magnetron Sputtering

2013 ◽  
Vol 543 ◽  
pp. 277-280
Author(s):  
Marius Dobromir ◽  
Alina Vasilica Manole ◽  
Simina Rebegea ◽  
Radu Apetrei ◽  
Maria Neagu ◽  
...  
Keyword(s):  
Thin Films ◽  
Magnetron Sputtering ◽  
Photoelectron Spectroscopy ◽  
Room Temperature ◽  
Rf Magnetron Sputtering ◽  
Rutile Phase ◽  
X Ray Diffraction ◽  
X Ray ◽  
Deposited Films

Rutile N-doped TiO2thin films were grown by RF magnetron sputtering on amorphous and crystalline substrates at room temperature. The surface elemental analysis, investigated by X-ray photoelectron spectroscopy indicated that the nitrogen content of the films could be adjusted up to values as high as 4.1 at.%. As demonstrated by the X-ray diffraction data, the as-deposited films (100 200 nm thick) showed no detectable crystalline structure, while after successive annealing in air for one hour at 400°C, 500°C and 600°C, the (110) rutile peaks occurred gradually as dominant features. The rutile phase in the films was confirmed by the band gap values of the deposited materials, which stabilized at 3.1 eV, for the thin films having 200 nm thicknesses.

The Structure and Magnetic Properties of NiZn-Ferrite Films Deposited by Magnetron Sputtering at Room Temperature

2013 ◽  
Vol 690-693 ◽  
pp. 1702-1706 ◽  
Author(s):  
Shuang Jun Nie ◽  
Hao Geng ◽  
Jun Bao Wang ◽  
Lai Sen Wang ◽  
Zhen Wei Wang ◽  
...  
Keyword(s):  
Thin Films ◽  
Magnetic Properties ◽  
Magnetron Sputtering ◽  
Saturation Magnetization ◽  
Room Temperature ◽  
Oxygen Flow ◽  
Flow Ratio ◽  
Study Results ◽  
Ferrite Thin Films ◽  
Ferrite Films

NiZn-ferrite thin films were deposited onto silicon and glass substrates by radio frequency magnetron sputtering at room temperature. The effects of the relative oxygen flow ratio on the structure and magnetic properties of the thin films were investigated. The study results reveal that the films deposited under higher relative oxygen flow ratio show a better crystallinity. Static magnetic measurement results indicated that the saturation magnetization of the films was greatly affected by the crystallinity, grain dimension, and cation distribution in the NiZn-ferrite films. The NiZn-ferrite thin films with a maximum saturation magnetization of 151 emucm-3, which is about 40% of the bulk NiZn ferrite, was obtained under relative oxygen flow ratio of 60%.

Characterization of Ti–Zr–V thin films deposited by DC and unipolar pulsed DC magnetron sputtering

Vacuum ◽  
2021 ◽  
Vol 188 ◽  
pp. 110200
Author(s):  
Sihui Wang ◽  
Wei Wei ◽  
Yonghao Gao ◽  
Haibin Pan ◽  
Yong Wang
Keyword(s):  
Thin Films ◽  
Magnetron Sputtering ◽  
Dc Magnetron Sputtering ◽  
Pulsed Dc ◽  
Pulsed Dc Magnetron Sputtering

scholarly journals Epitaxial growth and characterization of Cu thin films deposited on Al2O3(0001) substrates by magnetron sputtering

2021 ◽  
pp. 130119
Author(s):  
Ik-Jae Lee ◽  
Hee Seob Kim ◽  
Young Duck Yun ◽  
Seen-Woong Kang ◽  
Hyo-Yun Kim ◽  
...  
Keyword(s):  
Thin Films ◽  
Magnetron Sputtering ◽  
Epitaxial Growth

Processing by Pulsed Laser Deposition and Structural, Morphological and Chemical Characterization of Bi-Pb-Sr-Ca-Cu-O and Bi-Pb-Sb-Sr-Ca-Cu-O Thin Films

2010 ◽  
Vol 75 ◽  
pp. 202-207
Author(s):  
Victor Ríos ◽  
Elvia Díaz-Valdés ◽  
Jorge Ricardo Aguilar ◽  
T.G. Kryshtab ◽  
Ciro Falcony
Keyword(s):  
Thin Films ◽  
Pulsed Laser Deposition ◽  
Room Temperature ◽  
Pulsed Laser ◽  
Chemical Characterization ◽  
Laser Deposition ◽  
Nominal Composition ◽  
Deposition Parameters ◽  
The Relationship

Bi-Pb-Sr-Ca-Cu-O (BPSCCO) and Bi-Pb-Sb-Sr-Ca-Cu-O (BPSSCCO) thin films were grown on MgO single crystal substrates by pulsed laser deposition. The deposition was carried out at room temperature during 90 minutes. A Nd:YAG excimer laser ( = 355 nm) with a 2 J/pulse energy density operated at 30 Hz was used. The distance between the target and substrate was kept constant at 4,5 cm. Nominal composition of the targets was Bi1,6Pb0,4Sr2Ca2Cu3O and Bi1,6Pb0,4Sb0,1Sr2Ca2Cu3OSuperconducting targets were prepared following a state solid reaction. As-grown films were annealed at different conditions. As-grown and annealed films were characterized by XRD, FTIR, and SEM. The films were prepared applying an experimental design. The relationship among deposition parameters and their effect on the formation of superconducting Bi-system crystalline phases was studied.

Sign in / Sign up

Export Citation Format

Share Document