AN HISTORIC GEOLOGY OF THE GIPPSLAND BASIN

1970 ◽  
Vol 10 (1) ◽  
pp. 70
Author(s):  
L. C. P. Wooldridge ◽  
W. G. Hill

The Mesozoic and Tertiary rocks of the Gippsland Basin form a simple natural sequence as the deposits of a main regressive - transgressive cycle, followed by a regressive phase of lesser magnitude.After a period of early Mesozoic erosion in Gippsland, a river flowing from the north-west built extensive deposits which drove the sea back well beyond the present coast line. Strzelecki Formation is the name applied to the flood-plain sediments of this period. The channel belt deposits have been given various names and of these the Childers Formation appears to be the most valid. However, with the deltaic plain deposits, it can be regarded as forming a part of the Latrobe Valley Complex.About the end of Mesozoic time the sea began to transgress, also at this time there was some vulcanism in the western part of the basin. As transgression proceeded, the delta became digitate in form, similar to today's Mississippi delta. Silty and muddy sediments accumulated beyond the distributaries and between them, whilst the distributaries were areas of dominantly sand desposition. Marine agencies reworked some of the sand to form beaches and occasional barrier islands.As the sea transgressed the prodelta silty muds (Lakes Entrance Formation), covered the submerged distributaries and these in turn became covered by the cleaner water calcareous deposits of the Lower Gippsland Limestone. Meanwhile onshore, the flood-plain and earlier channel-belt deposits became overlain by later channel-belt deposits, and then by deltaic plain deposits with abundant coal. Transgression reached its zenith, probably during Miocene time, and a final regressive phase culminated in the situation as we see it today.The formation water in the main body of the Latrobe Valley complex is very fresh, and calculations show a static situation for both the Latrobe Valley and the contiguous glauconitic sandstone member, and thus the existence of down-dip escape is most unlikely. The oil at Lakes Entrance has not been flushed down-dip, rather it has moved up-dip.It follows from a consideration of the depositional history in Gippsland that producing structures at the top Latrobe Valley level are basically stratigraphic traps. They lie along ancient distributary channel trends and are flanked by contemporaneous muddy facies. Separate closures along the trends have been brought about by the development of saddles due to differential compaction and probably normal faulting at depth.The oil and gas pools today are more or less at their greatest depth of burial. An association is obvious between depth and hydrocarbon content for the top Latrobe Valley pools. A progression is noted from dry gas at Golden Beach (2,000') to a thick oil i Halibut (8,000'). Coal rank increases with depth. It is concluded that coal is the main hydrocarbon source in Gippsland. Thus all the Latrobe Valley section is prospective. The top Latrobe Valley horizon is probably the most productive to date because it has very effective cappingBarracouta 1, intersected a barrier island sand. There is likely to be more of these parallel to ancient shorelines. They could prove productive.

2002 ◽  
Vol 8 (2-3) ◽  
pp. 206-208
Author(s):  
V.G. Osadchyi ◽  
◽  
O.A. Prykhod'ko ◽  
I.I. Hrytsyk ◽  
◽  
...  

2018 ◽  
Vol 58 (2) ◽  
pp. 719
Author(s):  
Lourens Jacobs ◽  
Nancy Nguyen ◽  
Ryan Beccarelli

Woodside is an Australian oil and gas company and a leading global operator of offshore gas platforms and onshore LNG processing facilities. It is a public company listed on the Australian Securities Exchange headquartered in Perth, Western Australia. Woodside operates the Goodwyn A gas platform on behalf of the North West Shelf (NWS) Project. Woodside assessed Li-ion battery technology and considered the technology mature and ready to be utilised on offshore and onshore operating assets. Woodside operates dedicated islanded gas turbine power generation at each of its onshore and offshore facilities. It was concluded that a large battery energy storage solution (BESS) can deliver several advantages if connected to such an islanded power generation system. The most significant benefit materialises by using a BESS as backup (or spinning reserve) for the gas turbine generators (GTGs). Woodside decided to pioneer the Li-ion BESS technology in a first of its kind application on the NWS Project offshore Goodwyn A gas platform. The Goodwyn A BESS is designed for a 1 MW power and 1 MWh energy capacity, which is considered sufficient to provide the spinning reserve for the Goodwyn A platform. Currently, Goodwyn A operates four 3.2 MW GTGs to provide a typical load of 7–8 MW, with one GTG providing the N+1 spinning reserve. When the BESS is connected to the power generation system, Goodwyn A will operate three GTGs, with the BESS proving the backup in case one of the GTGs trip. The BESS will provide the full 1 MW for a minimum of 1 h, which will give the operators enough time to start the standby GTG or adjust the facility loads (load shedding). The result will be a decrease in overall fuel gas consumption (due to better efficiencies on the remaining GTGs in operation) and a related reduction in CO2 emissions. The project supports the overall objective of the North West Shelf Project to improve the energy intensity of its facilities by 5% by 2020. Woodside believes that developing capability and experience on the installation of BESSs, using Goodwyn A as an early adopter, will facilitate similar and larger installations on other Woodside operated offshore and onshore assets. This is one of the technologies Woodside believes will play an important role to ensure a lower carbon future globally.


2019 ◽  
Vol 59 (2) ◽  
pp. 493
Author(s):  
D. Lockhart ◽  
D. Spring

Available data for 2018 indicates that exploration activity is on the rise in Australia, compared to 2017, and this represents a second year of growth in exploration activity in Australia. There has been an increase in area under licence by 92 000 km2, reversing the downward trend in area under licence that commenced in 2014. Since 2016, exploratory drilling within Australia has seen a continued upward trend in both the number of wells drilled and the percentage of total worldwide. Onshore, 77 conventional exploration and appraisal wells were spudded during the year. Offshore, exploration and appraisal drilling matched that seen in 2017, with five new wells spudded: two in the Roebuck Basin, two in the Gippsland Basin and one in the North Carnarvon Basin. Almost 1500 km of 2D seismic and over 10 000 km2 of 3D seismic were acquired within Australia during 2018, accounting for 2.4% and 3.9% of global acquisition, respectively. This represents an increase in the amount of both 2D and 3D seismic acquired in Australia compared with 2017. Once the 2017 Offshore Petroleum Acreage Release was finalised, seven new offshore exploration permits were awarded as a result. A total of 12 bids were received for round one of the 2018 Offshore Petroleum Exploration Release, demonstrating an increase in momentum for offshore exploration in Australia. The permits are in Commonwealth waters off Western Australia, Victoria and the Ashmore and Cartier islands. In June 2018, the Queensland Government announced the release of 11 areas for petroleum exploration acreage in onshore Queensland, with tenders closing in February/March 2019; a further 11 areas will be released in early 2019. The acreage is a mix of coal seam gas and conventional oil and gas. Victoria released five areas in the offshore Otway Basin within State waters. In the Northern Territory, the moratorium on fracking was lifted in April, clearing the way for exploration to recommence in the 2019 dry season. With the increase in exploration has come an increase in success, with total reserves discovered within Australia during 2018 at just under 400 million barrels of oil equivalent, representing a significant increase from 2017. In 2018, onshore drilling resulted in 18 new discoveries, while offshore, two new discoveries were made. The most notable exploration success of 2018 was Dorado-1 drilled in March by Quadrant and Carnarvon Petroleum in the underexplored Bedout Sub-basin. Dorado is the largest oil discovery in Australia of 100 million barrels, or over, since 1996 and has the potential to reinvigorate exploration in the region.


2020 ◽  
Vol 60 (2) ◽  
pp. 588
Author(s):  
Meysam Banimahd ◽  
Steve Tyler ◽  
Matthew Kuo ◽  
Fiona Chow

The July 2019 magnitude 6.6 earthquake 200 km offshore from Broome is a recent reminder of the significant risk that earthquakes pose to oil and gas infrastructure in Australia. Unlike tropical cyclones, there are no reliable methods for predicting the timing, location and magnitude of imminent earthquakes. Appropriate risk management is therefore required, together with the implementation of emergency response and integrity management procedures, to manage the potential impacts to health, safety, process safety, the environment and production. Given the concentration of oil and gas infrastructure in the north west of Australia, a collaborative approach is advantageous for earthquake risk management and emergency response measures. This paper shares Woodside’s earthquake risk and integrity management procedures with the aim of enabling appropriate quality and consistency throughout the industry. The paper reviews state-of-the-art international practice in earthquake risk management for critical infrastructure from design to operation. Applicable seismic design criteria, likely failure modes and performance requirements are also described. Woodside’s real-time earthquake alert and integrity management systems are presented. Recommendations are made on best practice for earthquake risk management in the region and areas for further collaboration and improvement within the industry.


2018 ◽  
Vol 58 (2) ◽  
pp. 871 ◽  
Author(s):  
Melissa Thompson ◽  
Fred Wehr ◽  
Jack Woodward ◽  
Jon Minken ◽  
Gino D'Orazio ◽  
...  

Commencing in 2014, Quadrant Energy and partners have undertaken an active exploration program in the Bedout Sub-basin with a 100% success rate, discovering four hydrocarbon accumulations with four wells. The primary exploration target in the basin, the Middle Triassic Lower Keraudren Formation, encompasses the reservoirs, source rocks and seals that have trapped hydrocarbons in a self-contained petroleum system. This petroleum system is older than the traditional plays on the North-West Shelf and before recent activity was very poorly understood and easily overlooked. Key reservoirs occur at burial depths of 3500–5500 m, deeper than many of the traditional plays on the North-West Shelf and exhibit variable reservoir quality. Oil and gas-condensate discovered in the first two wells, Phoenix South-1 and Roc-1, raised key questions on the preservation of effective porosity and productivity sufficient to support a commercial development. With the acquisition and detailed interpretation of 119 m of core over the Caley Member reservoir in Roc-2 and a successful drill stem test that was surface equipment constrained to 55 MMscf/d, the productive potential of this reservoir interval has been confirmed. The results of the exploration program to date, combined with acquisition of new 3D/2D seismic data, have enabled a deeper understanding of the potential of the Bedout Sub-basin. A detailed basin model has been developed and a large suite of prospects and leads are recognised across a family of hydrocarbon plays. Two key wells currently scheduled for 2018 (Phoenix South-3 and Dorado-1) will provide critical information about the scale of this opportunity.


1993 ◽  
Vol 6 (6) ◽  
pp. 491 ◽  
Author(s):  
HA Martin

The principles of pollen dispersal and deposition show that the pollen spectrum is produced by the plants of the locality, with a little transported in from long distances. The 'locality' has a radius of no more than 500 m, and it could be much less. Adherence to these principles has allowed a detailed reconstruction of the palaeovegetation. Nothofagus grew throughout the Murray Basin, probably on the dry ground in the flood plain complex. Occasionally it was dominant, but most of the forests were mixed. The fusca-type flourished on well drained sites, especially in the north-east. The menziesii-type became prominent in the mid-Miocene, when the climate was becoming drier. The brassii-type was probably the only type in the deeper, swampier parts of the basin. Gymnosperms were intimately connected with the semi-swamp forest. Araucariaceae–Casuarinaceae forests formed a coastal zone around the Miocene marine incursion. Herbaceous fresh water swamps were found in the north-west, where they formed disjuncts from the swampy margin of Lake Frome. Myrtaceae was found throughout, sometimes abundantly, but eucalypts were rare. Geographic variation, changes through time and forest dynamics, including possibly one very rare modification after burning, are detailed.


Author(s):  
Sławomir OSZCZEPALSKI ◽  
Andrzej CHMIELEWSKI ◽  
Stanisław SPECZIK

The Polish Geological Institute – NRI has conducted investigations of the Kupferschiefer series since 1957, when the giant sediment-hosted stratiform Cu-Ag ore deposit was discovered in the central part of the Fore-Sudetic Monocline. Until 1991, a number of drilling programs were completed by PGI-NRI and later research has been focusing mainly on cooperation with oil and gas industry and their core material. Over the last few years, thanks to systematic examination of the drill holes located in the north-western extension, many prospective areas have been recognized and delineated. These prospects are located between Lubin-Sieroszowice deposit and the eastern part of the Zielona Góra oxidized field. In the Kożuchów area, the lower part of Zechstein copper-bearing series contain only relict sulphide mineralization accompanied by iron oxides while reduced rocks with metal sulphides occur in the uppermost part of Zechstein Limestone or at the base of Lower Anhydrite. Grochowice area, where reduced facies prevail in copper-bearing series, is characterized by the predomination of rich Cu-Ag mineralization proximaly to oxidized area. The western part of studied area is dominated by Cu-S type sulphides (chalcocite, digenite, covellite) whereas the eastern part is represented by Cu-Fe-S type minerals (bornite, chalcopyrite) with high galena and sphalerite concentrations. The spatial variability of sulphide mineralization with respect to the oxidized rocks indicates that Bytom Odrzański deposit extends in the north-west direction, continuing in the form of a copper belt along the eastern border of the oxidized area. An extensive deep exploration drilling program is implemented to verify the resource potential within predicted copper belt.


1969 ◽  
Vol 20 ◽  
pp. 15-18
Author(s):  
Finn Jakobsen ◽  
Claus Andersen

The Danish oil and gas production mainly comes from fields with chalk reservoirs of Late Cretaceous (Maastrichtian) and early Paleocene (Danian) ages located in the southern part of the Danish Central Graben in the North Sea. The area is mature with respect to exploration with most chalk fields located in structural traps known since the 1970s. However, the discovery by Mærsk Oil and Gas A/S of the large nonstructurally and dynamically trapped oil accumulation of the Halfdan Field in 1999 north-west of the Dan Field (e.g. Albrechtsen et al. 2001) triggered renewed exploration interest. This led to acquisition of new high quality 3-D seismic data that considerably enhanced imaging of different depositional features within the Chalk Group. Parallel to the endeavours by the operator to locate additional non-structural traps in porous chalk, the Geological Survey of Denmark and Greenland took advantage of the new data to unravel basin development by combining 3-D seismic interpretation of a large number of seismic markers, well log correlations and 2-D seismic inversion for prediction of the distribution of porous intervals in the Chalk Group. Part of this study is presented by Abramovitz et al. (in press). In the present paper we focus on aspects of the general structural development during the Late Cretaceous as illustrated by semi-regional time-isochore maps. The Chalk Group has been divided into two seismically mappable units (a Cenomanian–Campanian lower Chalk Unit and a Maastrichtian–Danian upper Chalk Unit) separated by a distinct basin-wide unconformity.


2001 ◽  
Vol 41 (1) ◽  
pp. 777
Author(s):  
B.F Ronalds

Oil and gas production is characterised by a truly international industry, and yet a unique local environment. Solutions developed elsewhere cannot always be imported directly for Australian use. For this reason alone, a strong local technology base is of value to the Australian oil and gas industry. Other benefits include the ability to provide high quality education and training for people entering, and already in, the industry.A case study is described where the Western Australian technology base is facilitating solutions to a specific challenge faced on the North West Shelf (NWS); namely, that the criteria for reliable development and operation of its offshore infrastructure for oil and gas production are more severe than other petroleum provinces, requiring new analytical tools to be developed.


Sign in / Sign up

Export Citation Format

Share Document