scholarly journals Shock synthesis of quasicrystals with implications for their origin in asteroid collisions

2016 ◽  
Vol 113 (26) ◽  
pp. 7077-7081 ◽  
Author(s):  
Paul D. Asimow ◽  
Chaney Lin ◽  
Luca Bindi ◽  
Chi Ma ◽  
Oliver Tschauner ◽  
...  

We designed a plate impact shock recovery experiment to simulate the starting materials and shock conditions associated with the only known natural quasicrystals, in the Khatyrka meteorite. At the boundaries among CuAl5, (Mg0.75Fe2+0.25)2SiO4 olivine, and the stainless steel chamber walls, the recovered specimen contains numerous micron-scale grains of a quasicrystalline phase displaying face-centered icosahedral symmetry and low phason strain. The compositional range of the icosahedral phase is Al68–73Fe11–16Cu10–12Cr1–4Ni1–2 and extends toward higher Al/(Cu+Fe) and Fe/Cu ratios than those reported for natural icosahedrite or for any previously known synthetic quasicrystal in the Al-Cu-Fe system. The shock-induced synthesis demonstrated in this experiment reinforces the evidence that natural quasicrystals formed during a shock event but leaves open the question of whether this synthesis pathway is attributable to the expanded thermodynamic stability range of the quasicrystalline phase at high pressure, to a favorable kinetic pathway that exists under shock conditions, or to both thermodynamic and kinetic factors.

2001 ◽  
Vol 16 (6) ◽  
pp. 1535-1540 ◽  
Author(s):  
S. M. Lee ◽  
B. H. Kim ◽  
D. H. Kim ◽  
W. T. Kim

Formation of the icosahedral quasicrystalline phase in conventionally cast Al62Cu25.5Fe12.5 and Al55Cu25.5Fe12.5Be7 alloys were investigated. The icosahedral phase (I-phase) forming ability was greatly improved by partial replacement of Al by 7 at.% Be. The as-cast Al55Cu25.5Fe12.5Be7 alloy consisted of dendritic primary I-phase and interdendritic τ-phase, whereas that of an as-cast Al62Cu25.5Fe12.5 alloy consisted of various phases such as the β-, I-, and τ-phases, together with a small amount of the λ- and η-phases. The kinetic barrier for transformation into single I-phase by heat treatment was greatly reduced in an Al55Cu25.5Fe12.5Be7 alloy. The I-phase in an Al55Cu25.5Fe12.5Be7 alloy has the same face centered icosahedral structure as that in an Al62Cu25.5Fe12.5 alloy and is of high quality without phason strain.


1985 ◽  
Vol 58 ◽  
Author(s):  
A. J. Drehman ◽  
S. J. Poon ◽  
K. R. Lawless

ABSTRACTMetallic glasses of composition Pd58.8U20.6Si20.6 can be transformed to a metastable single phase with quasicrystall ne order by thermal annealing. The icosahedral symmetry of this phase was verified by both electron and x-ray diffraction. Although the metallic glass can be formed over a broad compositional range the homogeneity range of this icosahedral phase is less than 1%. This indicates strong chemical ordering in the quasicrystalline state.


Alloy Digest ◽  
2015 ◽  
Vol 64 (1) ◽  

Abstract Sandvik Pressurfect is an austenitic chromium-nickel stainless steel with low carbon content used for high-pressure gasoline direct injection (GDI) fuel system. This datasheet provides information on composition, physical properties, hardness, elasticity, tensile properties, and bend strength. It also includes information on corrosion resistance as well as heat treating and machining. Filing Code: SS-1195. Producer or source: Sandvik Steel Company.


2017 ◽  
Vol 86 (8) ◽  
pp. 555-558
Author(s):  
Kana JOTOKU ◽  
Jun NAKAMURA ◽  
Takahiro OSUKI ◽  
Hiroyuki HIRATA

Author(s):  
Hideki Nakagawa

Practical application of fuel cell vehicle has started in the world, and high-pressure hydrogen tanks are currently considered to be the mainstream hydrogen storage system for commercially implemented fuel cell vehicle. Application of metallic materials to the components of high-pressure hydrogen storage system: hydrogen tanks, valves, measuring instructions and so on, have been discussed. In this work, tensile properties of four types of stainless steels were evaluated in 45MPa (6527psig) and 75MPa (10878psig) high-pressure gaseous hydrogen at a slow strain rate of 3×10−6 s−1 at ambient temperature. Type 316L (UNS S31603) stainless steel hardly showed ductility loss in gaseous hydrogen, since it had stable austenitic structure. On the other hand, Type 304 (UNS S30400) metastable austenitic stainless steel showed remarkable ductility loss in gaseous hydrogen, which was caused by the hydrogen embrittlement of strain induced martensitic phase. Likewise, Type 205 (UNS S20500) nitrogen-strengthened austenitic stainless steel showed remarkable ductility loss in gaseous hydrogen, though it had stable austenitic structure in the same manner as Type 316L. The ductility loss of Type 205 was due to the hydrogen embrittlement of austenitic phase resulting from the formation of planar dislocation array. Furthermore, Type 329J4L (UNS S31260) duplex stainless steel showed extreme ductility loss in gaseous hydrogen, which was caused by the hydrogen embrittlement of ferritic phase.


2016 ◽  
Vol 657 ◽  
pp. 215-223 ◽  
Author(s):  
Jenő Gubicza ◽  
Moustafa El-Tahawy ◽  
Yi Huang ◽  
Hyelim Choi ◽  
Heeman Choe ◽  
...  

2008 ◽  
Vol 373-374 ◽  
pp. 318-321
Author(s):  
J. Liang ◽  
M.K. Lei

Effects of stacking faults in a high nitrogen face-centered-cubic phase (γΝ) formed on plasma source ion nitrided 1Cr18Ni9Ti (18-8 type) austenitic stainless steel on peak shift and peak asymmetry of x-ray diffraction were investigated based on Warren’s theory and Wagner’s method, respectively. The peak shift from peak position of the γΝ phase is ascribed to the deformation faults density α, while the peak asymmetry of the γΝ phase is characterized by deviation of the center of gravity of a peak from the peak maximum (Δ C.G.) due to the twin faults density β. The calculated peak positions of x-ray diffraction patterns are consistent with that measured for plasma source ion nitrided 1Cr18Ni9Ti stainless steel.


2011 ◽  
Vol 239-242 ◽  
pp. 1300-1303
Author(s):  
Hong Cai Wang ◽  
Minoru Umemoto ◽  
Innocent Shuro ◽  
Yoshikazu Todaka ◽  
Ho Hung Kuo

SUS316L austenitic stainless steel was subjected to severe plastic deformation (SPD) by the method of high pressure torsion (HPT). From a fully austenitic matrix (γ), HPT resulted in phase transformation from g®a¢. The largest volume fraction of 70% a¢ was obtained at 0.2 revolutions per minute (rpm) while was limited to 3% at 5rpm. Pre-straining of g by HPT at 5rpm decreases the volume fraction of a¢ obtained by HPT at 0.2rpm. By HPT at 5rpm, a¢®g reverse transformation was observed for a¢ produced by HPT at 0.2rpm.


2014 ◽  
Vol 793 ◽  
pp. 23-27
Author(s):  
C. Patiño-Carachure ◽  
J. Luis López-Miranda ◽  
F. de la Rosa ◽  
M. Abatal ◽  
R. Pérez ◽  
...  

In this investigation the Al64Cu24Fe12 alloy was melted in an induction furnace and solidified under normal casting conditions. The as-cast sample was subject to a heat treatment at 700 oC under argon atmosphere in order to obtain the icosahedral quasicrystalline phase in a monophase region. Subsequently, the icosahedral phase was milled for different times and water added conditions. The pre-alloyed and milled powders were characterized using scanning electron microscopy, X-Ray diffraction, and transmission electron microscopy. The experimental results showed that the icosahedral phase is sensitive to the reaction between water and aluminum of the quasicrystalline alloy to generate hydrogen. As the milling time and the amount of water are increased, the embrittlement reaction of the alloy is accentuated releasing more hydrogen.


Sign in / Sign up

Export Citation Format

Share Document