Influence of Calcium Bentonite Addition on the Compressive Strength, Efflorescence Extent and Drying Shrinkage of Fly-Ash Based Geopolymer Mortar

2020 ◽  
Vol 79 (2) ◽  
pp. 77-82
Author(s):  
Yi Huang
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Drying Shrinkage ◽  
Calcium Bentonite

scholarly journals Effect of Fly Ash on Compressive Strength, Drying Shrinkage, and Carbonation Depth of Mortar with Ferronickel-Slag Powder

2021 ◽  
Vol 11 (3) ◽  
pp. 1037
Author(s):  
Se-Jin Choi ◽  
Ji-Hwan Kim ◽  
Sung-Ho Bae ◽  
Tae-Gue Oh
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Construction Industry ◽  
Bituminous Coal ◽  
Raw Materials ◽  
Drying Shrinkage ◽  
The Other ◽  
Test Results ◽  
Slag Powder ◽  
Ferronickel Slag

In recent years, efforts to reduce greenhouse gas emissions have continued worldwide. In the construction industry, a large amount of CO2 is generated during the production of Portland cement, and various studies are being conducted to reduce the amount of cement and enable the use of cement substitutes. Ferronickel slag is a by-product generated by melting materials such as nickel ore and bituminous coal, which are used as raw materials to produce ferronickel at high temperatures. In this study, we investigated the fluidity, microhydration heat, compressive strength, drying shrinkage, and carbonation characteristics of a ternary cement mortar including ferronickel-slag powder and fly ash. According to the test results, the microhydration heat of the FA20FN00 sample was slightly higher than that of the FA00FN20 sample. The 28-day compressive strength of the FA20FN00 mix was approximately 39.6 MPa, which was higher than that of the other samples, whereas the compressive strength of the FA05FN15 mix including 15% of ferronickel-slag powder was approximately 11.6% lower than that of the FA20FN00 mix. The drying shrinkage of the FA20FN00 sample without ferronickel-slag powder was the highest after 56 days, whereas the FA00FN20 sample without fly ash showed the lowest shrinkage compared to the other mixes.

Study on Production of Autoclaved Aerated Concrete by Coal Gangue Fly Ash

2013 ◽  
Vol 357-360 ◽  
pp. 949-954
Author(s):  
Ye Zhang ◽  
Peng Xuan Duan ◽  
Bao Sheng Jia ◽  
Lei Li
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Drying Shrinkage ◽  
Coal Gangue ◽  
National Standards ◽  
Raw Material ◽  
Autoclaved Aerated Concrete ◽  
Binder Ratio ◽  
Material Formulation ◽  
Aerated Concrete

In this paper, the low-silicon coal gangue fly ash is used to produce autoclaved aerated concrete. The influences of water binder ratio, coal gangue fly ash content, calcareous content and conditioning agents on the compressive strength of the autoclaved aerated concrete are investigated. Optimal raw material formulation and procedure are determined for the autoclaved aerated concrete. The compressive strength and frost resistance of autoclaved aerated concrete made by the optimal raw material formulation and procedure meet with the requirements of autoclaved aerated concretes of B05 grade, and its thermal conductivity, drying shrinkage reach the requirements of the relevant national standards of China.

Utilization of Fly Ash with Higher Loss on Ignition for Geopolymer Mortar

2015 ◽  
Vol 1129 ◽  
pp. 614-620
Author(s):  
Yasutaka Sagawa ◽  
Shu Ota ◽  
Koji Harada ◽  
Takeyoshi Nishizaki ◽  
Hiroki Goda
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Coal Fly Ash ◽  
Drying Shrinkage ◽  
Silicate Material ◽  
Loss On Ignition ◽  
Heat Curing ◽  
Higher Temperature ◽  
Curing Condition ◽  
Class F Fly Ash

In this study, utilization of coal fly ash with higher loss on ignition (LOI) for geopolymer mortar was investigated. The fly ash with approximately 9% of LOI was compared with Class F fly ash. Relationship between heat curing condition and strength was clarified. As the results, although compressive strength of geopolymer mortar with higher LOI was 30-50% smaller, it was available for geopolymer mortar as an alumina silicate material. The higher temperature and the longer period for initial curing, the higher strength was obtained. In order to decrease drying shrinkage, the higher temperature and the longer period for heat curing were required.

EVALUATION OF SHRINKAGE AND DURABILITY OF GEOPOLYMER CONCRETE USING F-CLASS COAL ASHES

2014 ◽  
Vol 1 (1) ◽  
Author(s):  
Gum Sung Ryu ◽  
Kyung Taek Koh ◽  
Gi Hong An ◽  
Jang Hwa Lee
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Bottom Ash ◽  
Drying Shrinkage ◽  
Geopolymer Concrete ◽  
Cement Concrete ◽  
Fly Ash Concrete ◽  
Coal Ashes

This paper evaluates the strength, shrinkage and durability characteristics of concrete using 100% fly ash and bottom ash as binder. It is seen that the compressive strength of activated fly ash and bottom ash concrete reaches respectively 25 MPa and 30 MPa, and that the change in strength is insignificant as per the content of bottom ash powder. Moreover, the total amount of shrinkage of the activated bottom ash concrete appears to be larger than that of the activated fly ash concrete. In addition, the drying shrinkage and durable performance of the activated ash geopolymer concrete is verified to be superior to that of ordinary cement concrete.

Drying Shrinkage of Fly Ash Mortar Mixed with Seawater

2015 ◽  
Vol 802 ◽  
pp. 118-123 ◽  
Author(s):  
John Wilmer Bautista ◽  
John Benedict Crockett ◽  
Beatrice Ann Liu ◽  
Timothy John Obra ◽  
Cheryl Lyne Roxas
Keyword(s):  
Carbon Dioxide ◽  
Compressive Strength ◽  
Fly Ash ◽  
Carbon Dioxide Emissions ◽  
Drying Shrinkage ◽  
Water Shortage ◽  
Ash Content ◽  
Partial Substitution ◽  
Partial Replacement ◽  
Micro Cracks

Drying shrinkage in mortar produces cracks and micro-cracks which affect the durability of a structure. The effects of seawater as a substitute to freshwater and fly ash as a partial replacement for cement were investigated in this study in order to address the predicted water shortage by 2025 and the increasing carbon footprint from carbon dioxide emissions worldwide. Moreover, these materials are also more economical alternatives to freshwater and cement. Rectangular prism specimens with varying fly ash content (10%, 15%, 20%, 25%, and 30%) were cast to measure the drying shrinkage in mortar while 50-mm cube mortar specimens were prepared to determine the compressive strength. This study investigated whether the addition of fly ash and seawater reduced the drying shrinkage of mortar. From the results, it was found that mortar specimens with 20% fly ash replacement achieved the highest early and late strengths. Partial substitution of fly ash would result to shrinkage in mortar while substitution of seawater to freshwater counteracts the effects of fly ash, thus producing less shrinkage. Fly ash content between 20%-25% combined with seawater produces the least shrinkage value without compromising the minimum required compressive strength.

Effects of Change in Fineness of Fly Ash on Air-Entrained Concrete

2010 ◽  
Vol 168-170 ◽  
pp. 2195-2199 ◽  
Author(s):  
Hong Zhu Quan ◽  
Hideo Kasami
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Laboratory Experiments ◽  
Drying Shrinkage ◽  
Test Results ◽  
Air Entrained Concrete

In order to make clear of the effects of the change in fineness of fly ash on air-entrained concrete, 2 series of laboratory experiments were carried out using 6 kinds fly ash with the specific surface area in the range from 2500 to 4400cm2/g. The test results indicated higher slump and lower air-entraining content and higher dosage of air-entraining agent for fly ash with higher specific surface area. Compressive strength was found to increase with the increases of specific surface area of fly ash, while drying shrinkage and carbonation were found to show different tendency with change in fineness of fly ash.

Dry Shrinkage and Compressive Strength of Blended Cement Pastes with Fly Ash and Silica Fume

2012 ◽  
Vol 535-537 ◽  
pp. 1735-1738 ◽  
Author(s):  
Yan Li ◽  
Dao Sheng Sun ◽  
Xiu Sheng Wu ◽  
Ai Guo Wang ◽  
Wei Xu ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Silica Fume ◽  
Cement Paste ◽  
Blended Cement ◽  
Drying Shrinkage ◽  
Cementitious Material ◽  
Strength Increase ◽  
Cement Pastes ◽  
Dry Shrinkage

This paper reports the drying shrinkage and compressive strength results of cement pastes with fly ash and silica fume. In this study, Portland cement (PC) was used as the basic cementitious material. Fly ash (FA) and silica fume (SF) were used as cement replacement materials at levels of 0%, 5%, 10%, and 15% , 40%, 35%, 25%, and 15% by weight of the total cementitious material, respectively. The water/cement (PC + FA + SF) ratios (w/c) was 0.28 by weight. The samples produced from fresh pastes were demoulded after a day; then they were cured at 20 ±1°C with 50 ± 3% relative humidity (RH) until the samples were used for drying shrinkage and compressive strength measurement at various ages. The results show that drying shrinkage and compressive strength increase with increasing SF content, and the optimum composition of blended cement pastes is the cement paste with 30% fly ash and 10% silica fume, which possesses lower drying shrinkage values than that of plain cement paste and higher early age strength than that of blended cement pastes with fly ash. Furthermore, a linear relationship is established between compressive strength and drying shrinkage. By comparing the development of compressive strength and the drying shrinkage deformations, it appears possible to predict the drying shrinkage according to the acquired compressive strength.

scholarly journals An experimental study on production of high strength non-shrink grout containing fly ash

2021 ◽  
Vol 72 (4) ◽  
pp. 477-485
Author(s):  
Chi Dang Thuy
Keyword(s):  
Experimental Study ◽  
Compressive Strength ◽  
Fly Ash ◽  
Drying Shrinkage ◽  
High Strength ◽  
Fine Aggregate ◽  
Expansive Agent ◽  
Chemical Admixture ◽  
The University ◽  
The Given

Cement-based grouts are widely used thanks to its outstanding features such as high workability, non-separation, non-bleeding, easy to fulfill small gaps with complex shapes. This paper descrcibes the first phase of a series of laboratory experiments that examined the ability of production of self - levelling mortar at the University of Transport and Communications. The Portland cement-based grout incorporated superplasticizer, fly ash, fine aggregate, water along with expansion agent to match as closed as possible the given high strength non-shrink grout. The experimental study focused on the performance of non-shrink grouts regarding the flowability, expansion and bleeding, strengths and drying shrinkage of the test grout mixtures. The high range water reducer (HRWR) at dosage of 1% by weight of cement was used as a flowability modifying chemical admixture to prevent water segregation and leads to an increase in compressive strength. The parameter tests consist of water-cement ratios, and fixed dosages of superplasticizer and expansive agent. To examine the flowability of grout mortars, the flow cone test was applied. The flow cone test result indicated that there were three proportional of grouts that can meet the requirement of fluidity. The compressive strength of specimens was tested according to ASTM C349-14. It was concluded that the compositions of grouts at a water-cement ratio of from 0.29 to 0.33 have compressive strengths greater than 60 MPa. The tested specimens using the expansive agent with the dosage recommended by the manufacturer meet the non-shrinkage requirement of a grout. The experimental results have demonstrated the ability of production of high strength non-shrink grouts.

Sign in / Sign up

Export Citation Format

Share Document