Photon Transmission Study on Conformational Ordering of Iota-Carrageenan in CaCl2 Solution

2005 ◽  
Vol 22 (6) ◽  
pp. 747-754 ◽  
Author(s):  
Selim Kara ◽  
Önder Pekcan
Author(s):  
G. M. Greene ◽  
J. W. Sprys

The present study demonstrates that fracture surfaces appear strikingly different when observed in the transmission electron microscope by replication and in the scanning electron microscope by backscattering and secondary emission. It is important to know what form these differences take because of the limitations of each instrument. Replication is useful for study of surfaces too large for insertion into the S.E.M. and for resolution of fine detail at high magnification with the T.E.M. Scanning microscopy reduces sample preparation time and allows large sections of the actual surface to be viewed.In the present investigation various modes of the S.E.M. along with the transmission mode in the T.E.M. were used to study one area of a fatigue surface of a low carbon steel. Following transmission study of a platinum carbon replica in the T.E.M. and S.E.M. the replica was coated with a gold layer approximately 200A° in thickness to improve electron emission.


Foods ◽  
2021 ◽  
Vol 10 (6) ◽  
pp. 1368
Author(s):  
Marbie Alpos ◽  
Sze Ying Leong ◽  
Indrawati Oey

Legumes are typically soaked overnight to reduce antinutrients and then cooked prior to consumption. However, thermal processing can cause over-softening of legumes. This study aimed to determine the effect of calcium addition (0, 100, 300, and 500 ppm in the form of calcium chloride, CaCl2), starting from the overnight soaking step, in reducing the loss of firmness of black beans during thermal processing for up to 2 h. The impact of calcium addition on the in vitro starch and protein digestibility of cooked beans was also assessed. Two strategies of calcium addition were employed in this study: (Strategy 1/S1) beans were soaked and then cooked in the same CaCl2 solution, or (Strategy 2/S2) cooked in a freshly prepared CaCl2 solution after the calcium-containing soaking medium was discarded. Despite the texture degradation of black beans brought about by increasing the cooking time, texture profile analysis (TPA) revealed that their hardness, cohesiveness, springiness, chewiness, and resilience improved significantly (p < 0.05) with increasing calcium concentration. Interestingly, beans cooked for 2 h with 300 ppm CaCl2 shared similar hardness with beans cooked for 1 h without calcium addition. Starch and protein digestibility of calcium-treated beans generally improved with prolonged cooking. However, calcium-treated beans cooked for 1 h under S2 achieved a reduced texture loss and a lower starch digestibility than those beans treated in S1. A lower starch digestion could be desired as this reflects a slow rise in blood glucose levels. Findings from this result also showed that treating black beans with high level of CaCl2 (i.e., 500 ppm) was not necessary, otherwise this would limit protein digestibility of cooked black beans.


2004 ◽  
Vol 189 (5) ◽  
pp. 847-851 ◽  
Author(s):  
Ashley C. LaMonte ◽  
Mary E. Paul ◽  
Jennifer S. Read ◽  
Margaret M. Frederick ◽  
Dean D. Erdman ◽  
...  

BioResources ◽  
2021 ◽  
Vol 16 (3) ◽  
pp. 5780-5793
Author(s):  
Ji-Soo Park ◽  
Chan-Woo Park ◽  
Song-Yi Han ◽  
Eun-Ah Lee ◽  
Azelia Wulan Cindradewi ◽  
...  

Cellulose nanocrystals (CNCs) were wet-spun in a coagulation bath for the fabrication of microfilaments, and the effect of sodium alginate (AL) addition on the wet-spinnability and properties of the microcomposite filament was investigated. The CNC suspension exhibited excellent wet-spinnability in calcium chloride (CaCl2) solution, and the addition of AL in CNC suspension resulted in the enhancement of the wet-spinnability of CNCs. As the AL content increased from 3% to 10%, the average diameter of the microcomposite filament decreased, and its tensile properties deteriorated. The increased spinning rate caused an increase in the orientation index of CNCs, resulting in an improvement in the tensile properties of the microcomposite filament.


Author(s):  
Masatoshi Takeda ◽  
Tsuyoshi Nishimura ◽  
Takashi Kudo ◽  
Satoshi Tanimukai ◽  
Toshihisa Tanaka ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document