Influence of twist boundary on deformation behaviour of 〈1 0 0〉 BCC Fe nanowires

2016 ◽  
Vol 96 (12) ◽  
pp. 469-476 ◽  
Author(s):  
G. Sainath ◽  
B. K. Choudhary
Keyword(s):  
Deformation Behaviour ◽  
Twist Boundary

Structure and migration of planar defects in crystals observed in atomic scale

1978 ◽  
Vol 36 (1) ◽  
pp. 284-285 ◽  
Author(s):  
H. Hashimoto ◽  
Y. Sugimoto ◽  
Y. Takai ◽  
H. Endoh
Keyword(s):  
Electron Microscope ◽  
Rotation Angle ◽  
Crystal Surface ◽  
Electron Gun ◽  
Atomic Scale ◽  
Present Observation ◽  
Twist Boundary ◽  
Optical Magnification ◽  
Zinc Crystal ◽  
And Migration

As was demonstrated by the present authors that atomic structure of simple crystal can be photographed by the conventional 100 kV electron microscope adjusted at “aberration free focus (AFF)” condition. In order to operate the microscope at AFF condition effectively, highly stabilized electron beams with small energy spread and small beam divergence are necessary. In the present observation, a 120 kV electron microscope with LaB6 electron gun was used. The most of the images were taken with the direct electron optical magnification of 1.3 million times and then magnified photographically.1. Twist boundary of ZnSFig. 1 is the image of wurtzite single crystal with twist boundary grown on the surface of zinc crystal by the reaction of sulphur vapour of 1540 Torr at 500°C. Crystal surface is parallel to (00.1) plane and electron beam is incident along the axis normal to the crystal surface. In the twist boundary there is a dislocation net work between two perfect crystals with a certain rotation angle.

Observation of secondary slip systems in tungsten bicrystals

1984 ◽  
Vol 42 ◽  
pp. 478-479
Author(s):  
J. R. Fekete ◽  
R. Gibala
Keyword(s):  
Stress Field ◽  
Grain Boundaries ◽  
Deformation Behavior ◽  
Stress Axis ◽  
Polycrystalline Materials ◽  
Slip Systems ◽  
Metallic Materials ◽  
Twist Boundary ◽  
Secondary Slip ◽  
Plane Normal

The deformation behavior of metallic materials is modified by the presence of grain boundaries. When polycrystalline materials are deformed, additional stresses over and above those externally imposed on the material are induced. These stresses result from the constraint of the grain boundaries on the deformation of incompatible grains. This incompatibility can be elastic or plastic in nature. One of the mechanisms by which these stresses can be relieved is the activation of secondary slip systems. Secondary slip systems have been shown to relieve elastic and plastic compatibility stresses. The deformation of tungsten bicrystals is interesting, due to the elastic isotropy of the material, which implies that the entire compatibility stress field will exist due to plastic incompatibility. The work described here shows TEM observations of the activation of secondary slip in tungsten bicrystals with a [110] twist boundary oriented with the plane normal parallel to the stress axis.

scholarly journals Laboratory Study of Deformation Behaviour of Two New Reinforcing Polymeric TSLs and Their Potential Application in Deep Underground Coal Mine

Polymers ◽  
2021 ◽  
Vol 13 (13) ◽  
pp. 2205
Author(s):  
Han Liang ◽  
Jun Han ◽  
Chen Cao ◽  
Shuangwen Ma
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Underground Mining ◽  
Deformation Behaviour ◽  
Polymer Materials ◽  
Surface Protection ◽  
Steel Mesh ◽  
Geological Conditions ◽  
Deep Underground ◽  
Roadway Support

Thin spray-on liner (TSL) is a surface protection technology used by spraying a polymer film, which is widely used for mine airtightness and waterproofing. A reinforcing TSL can replace steel mesh, which is a new method for roadway support. This paper reviews the development of a reinforcing TSL. Considering the deterioration of geological conditions in deep underground mining and the demand for reinforcing automation, two kinds of polymeric reinforcing TSL (RPTSL) materials are developed. The mechanical characteristics of the new TSL materials are studied experimentally. Results show that the average compressive strength, tensile strength, cohesion, and internal friction angle of the two TSL materials are 52 and 32 MPa, 12 and 8 MPa, 6.2 and 17.2 MPa, and 33.6° and 25.9°, respectively. The bonding strength between the two materials and coal is greater than the tensile strength of coal itself, and the mechanical properties of the material for comparison are lower than those of both materials. Based on the TSL support mechanism, we examine the application of the two TSL materials to the mining environment and compare the mechanical properties of polymer materials and cement-based materials. The advantages of polymer materials include versatile mechanical properties, good adhesion, and high early strength. This study provides a new support material to replace steel mesh for roadway surface support, which satisfies the needs of different surface support designs under complex geological conditions, and promotes the automation of roadway support.

Influence of the contact with friction on the deformation behavior of advanced high strength steels in the Nakajima test

2021 ◽  
pp. 030932472110212
Author(s):  
Mohammad Mehdi Kasaei ◽  
Marta C Oliveira
Keyword(s):  
Finite Element ◽  
Friction Coefficient ◽  
Strain Rate ◽  
Contact Pressure ◽  
Deformation Behaviour ◽  
High Strength Steels ◽  
High Strength ◽  
Advanced High Strength Steels ◽  
Deformation Mechanics ◽  
Nakajima Test

This work presents a new understanding on the deformation mechanics involved in the Nakajima test, which is commonly used to determine the forming limit curve of sheet metals, and is focused on the interaction between the friction conditions and the deformation behaviour of a dual phase steel. The methodology is based on the finite element analysis of the Nakajima test, considering different values of the classic Coulomb friction coefficient, including a pressure-dependent model. The validity of the finite element model is examined through a comparison with experimental data. The results show that friction affects the location and strain path of the necking point by changing the strain rate distribution in the specimen. The strain localization alters the contact status from slip to stick at a portion of the contact area from the pole to the necking zone. This leads to the sharp increase of the strain rate at the necking point, as the punch rises further. The influence of the pressure-dependent friction coefficient on the deformation behaviour is very small, due to the uniform distribution of the contact pressure in the Nakajima test. Moreover, the low contact pressure range attained cannot properly replicate real contact condition in sheet metal forming processes of advanced high strength steels.

Sign in / Sign up

Export Citation Format

Share Document