Improved fits of coronal radiative cooling rates for high-temperature plasmas

2018 ◽  
Vol 173 (5-6) ◽  
pp. 388-398 ◽  
Author(s):  
A. A. Mavrin
1977 ◽  
Vol 20 (5) ◽  
pp. 397-439 ◽  
Author(s):  
D.E. Post ◽  
R.V. Jensen ◽  
C.B. Tarter ◽  
W.H. Grasberger ◽  
W.A. Lokke

1977 ◽  
Author(s):  
D.E. Post ◽  
R.V. Jensen ◽  
C.B. Tarter ◽  
W.H. Grasberger ◽  
W.A. Lokke

2019 ◽  
Vol 27 (2) ◽  
pp. 51-54 ◽  
Author(s):  
E. S. Skorbyaschensky ◽  
V. F. Bashev ◽  
A. N. Polishko ◽  
S. N. Antropov

The method of quenching in tin melt was tested for low-weight parts with a large specific surface, made of a number of steels with a high temperature of the onset of martensitic transformation. The advantages of this method in comparison with traditional hardening technologies are established, as well as regularities in the change of cooling curves for various mass ratios of the part and the quencher are revealed. The practical possibility of adjusting the cooling rates in the process of hardening in various temperature ranges in order to optimize the phase ratio in steel while maintaining the possibility of preventing the occurrence of microcracks is shown.


1981 ◽  
Vol 34 (9) ◽  
pp. 1845 ◽  
Author(s):  
LH Cohen ◽  
Jr W Klement

Differential thermal analyses have located the transitions between low-temperature I and high-temperature II phases in AgNO3 powder and single crystals under hydrostatic pressures </~0.7 GPa, with heating/cooling rates in the range 0.1-1.5 K s-1. Isobaric transition temperatures plot linearly against heating/cooling rates and, extrapolated to zero rate, show hystereses between I → II and II → I transition temperatures which are comparable with the 'regions of indifference' of Bridgman's isothermal experiments. The present results suggest an initial slope of -0.090 μK Pa-1 and zero initial curvature for the I-II phase boundary. Greater hystereses are observed for the I-II transitions near intersection with the II-II' λ transition at </~0.7 GPa. An improved, quantitative description is achieved for the Kennedy-Schultz data on the linear growth rates of II,II? → I at 0.1 MPa. For II' (with ordered NO3- ions) → I the growth rates show temperature dependence markedly different than growth rates for II(with disordered NO3-) → 1 and I → II.


Author(s):  
Michael Katcher ◽  
Dwaine L. Klarstrom

HAYNES 230 and 617 alloys are competing for use on Generation IV, high temperature gas cooled reactor components because of their good high temperature creep strength in the temperature range of 760°C and 982°C and resistance to attack in the gas cooled reactor environment. A review of the metallurgy affecting the properties in each alloy is provided. It is shown that the grain size and carbide precipitation developed during manufacture affect short term and long term ductility, fatigue life, and creep strength. For example, 230 alloy has a finer grained structure which promotes fatigue strength with a slight sacrifice in creep strength. The 617 alloy has a coarser grain structure which provides slightly higher creep resistance while sacrificing some fatigue strength. Thermal aging also introduces gamma prime precipitation to 617 alloy in addition to grain boundary carbides. This, along with grain boundary oxidation, reduces the low cycle fatigue strength of 617 alloy compared to 230 alloy. Independent studies have shown that 230 alloy possesses higher resistance to thermal fatigue than 617 alloy. However, welds of both base metals with similar weld composition have about the same thermal fatigue life. Cooling rates from solution annealing temperatures during processing affect the ductility and creep strength of these alloys with the highest cooling rates preferred for retention of ductility and creep strength. Slow cooling rates promote carbide precipitation in the grain boundaries which reduces ductility and creep strength.


2007 ◽  
Vol 556-557 ◽  
pp. 371-374 ◽  
Author(s):  
Andreas Gällström ◽  
Björn Magnusson ◽  
Patrick Carlsson ◽  
Nguyen Tien Son ◽  
Anne Henry ◽  
...  

The influence of different cooling rates on deep levels in 4H-SiC after high temperature annealing has been investigated. The samples were heated from room temperature to 2300°C, followed by a 20 minutes anneal at this temperature. Different subsequent cooling sequences down to 1100°C were used. The samples have been investigated using photoluminescence (PL) and IV characteristics. The PL intensities of the silicon vacancy (VSi) and UD-2, were found to increase with a faster cooling rate.


2020 ◽  
Vol 77 (2) ◽  
pp. 479-497 ◽  
Author(s):  
Nadir Jeevanjee ◽  
Stephan Fueglistaler

Abstract Atmospheric radiative cooling is a fundamental aspect of Earth’s greenhouse effect, and is intrinsically connected to atmospheric motions. At the same time, basic aspects of longwave radiative cooling, such as its characteristic value of 2 K day−1, its sharp decline (or “kink”) in the upper troposphere, and the large values of CO2 cooling in the stratosphere, are difficult to understand intuitively or estimate with pencil and paper. Here we pursue such understanding by building simple spectral (rather than gray) models for clear-sky radiative cooling. We construct these models by combining the cooling-to-space approximation with simplified greenhouse gas spectroscopy and analytical expressions for optical depth, and we validate these simple models with line-by-line calculations. We find that cooling rates can be expressed as a product of the Planck function, a vertical emissivity gradient, and a characteristic spectral width derived from our simplified spectroscopy. This expression allows for a pencil-and-paper estimate of the 2 K day−1 tropospheric cooling rate, as well as an explanation of enhanced CO2 cooling rates in the stratosphere. We also link the upper-tropospheric kink in radiative cooling to the distribution of H2O absorption coefficients, and from this derive an analytical expression for the kink temperature Tkink ≈ 220 K. A further, ancillary result is that gray models fail to reproduce basic features of atmospheric radiative cooling.


Materials ◽  
2020 ◽  
Vol 13 (19) ◽  
pp. 4256
Author(s):  
Xiao-Yan Wang ◽  
Meng Li ◽  
Zhi-Xun Wen

The as-cast alloy of nickel-based single-crystal superalloy was used as the research object. After four hours of solution treatment at 1315 °C, four cooling rates (water cooling (WC), air cooling (AC) and furnace cooling (FC1/FC2)) were used to reduce the alloy to room temperature. Four different microstructures of nickel-based superalloy material were prepared. A high-temperature tensile test at 980 °C was carried out to study the influence of various rates on the formation of the material’s microstructure and to further obtain the influence of different microstructures on the high-temperature mechanical properties of the materials. The results show that an increase of cooling rate resulted in a larger γ′ phase nucleation rate, formation of a smaller γ′ phase and a greater number. When air cooling was used, the uniformity of the γ′ phase and the coherence relationship between the γ′ phase and the γ phase were the best. At the same time, the test alloy had the best high-temperature tensile properties, and the material showed a certain degree of plasticity. TEM test results showed that the test alloy mainly blocked dislocations from traveling in the material through the strengthening effect of γ′, and that AC had the strongest hindering effect on γ′ dislocation movement.


Sign in / Sign up

Export Citation Format

Share Document