Atomic Mixing Induced by Ion Irradiation of V/Cu Multilayers

2020 ◽  
Vol 37 (3) ◽  
pp. 036101
Author(s):  
Yan-Bin Sheng ◽  
Hong-Peng Zhang ◽  
Tie-Long Shen ◽  
Kong-Fang Wei ◽  
Long Kang ◽  
...  
1988 ◽  
Vol 3 (6) ◽  
pp. 1063-1071 ◽  
Author(s):  
U. G. Akano ◽  
D. A. Thompson ◽  
W. W. Smeltzer ◽  
J. A. Davies

Atomic mixing in Ni/Pd bilayer films due to 120 keV Ar+ irradiation in the thermally assisted regime (523−673 K) has been measured, in situ, using Rutherford backscattering with 2.0 MeV 4He+ ions. The mean diameter of grains in these polycrystallinc films increased from 10 to 60 nm, following Ar+ bombardment at 573 K. Initial mixing was rapid due to grain boundary diffusion and incorporation of the metal solute into the solvent metal matrix by grain growth; this mixing stage was essentially complete within 10 min for annealed films or after an Ar+ dose of 4 × 1015 cm−2 in irradiated films (10 min irradiation). No further measurable mixing occurred in the annealed, unirradiated films. For the irradiated samples the initial rapid mixing (6−35 atoms/ion) was followed by a slower mixing stage of 0.7–1.8 atoms/ion for irradiation doses of up to 2.5 × 1016 Ar+ cm−2. The Ar+ bombardment gave rise to much smaller mixing levels when the Pd films were deposited on large-grain or single-crystal Ni. A diffusion analysis demonstrates that the effective diffusivity, Deff, for ion-irradiation-enhanced mixing in the thermally assisted regime satisfied the relation Dl < Deff < DB, where the ratio of the grain boundary to lattice diffusivity was DB/Dl > 106.


2003 ◽  
Vol 792 ◽  
Author(s):  
H. Wanzenboeck ◽  
S. Harasek ◽  
H. Langfischer ◽  
B. Basnar ◽  
W. Brezna ◽  
...  

ABSTRACTThe focused ion beam has been acknowledged as a versatile tool for local sputtering as well as local deposition of material. A beam diameter below 10 nm is feasible and renders FIB a powerful tool for microstructure fabrication and generation. This experimental study investigates the geometrical limitations of FIB processing as well as the implications on the processed material. The high energetic ions of the primary beam also change the properties of the processed material due to implantation and atomic mixing. The incorporation of Ga from the FIB may be beneficial in the case of deliberate implantation or unfavorable as a chemical impurity. Higher doses of ion irradiation caused amorphisation of the material. The effects of FIB processing on the substrates as well as deposited structures are illustrated.


1995 ◽  
Vol 388 ◽  
Author(s):  
R.S. Averback ◽  
Mai Ghaly ◽  
Huilong Zhu

AbstractMD simulations have been employed to investigate damage processes near surfaces during keV bombardment of metal targets. For self-ion implantation of au, Cu, and Pt in the range of 5-20 keV, we have found that the proximity of the surface leads to significantly more damage and atomic mixing in comparison to recoil events occurring in the crystal interior. IN some cases, large craters are formed in a micro-explosive event, while in others a convective flow of atoms to the surface creates adatoms and leaves dislocations behind. Both the amount damage created in the surface and its morphology depend sensitively on the details of the energy deposition along individual ion trajectories. the results of these simulations will be summarized and compared to recent scanning tunneling microscopy studies of individual ion impacts in Pt and Ge.


1994 ◽  
Vol 373 ◽  
Author(s):  
R.S. Averback ◽  
Mai Ghaly ◽  
Huilong Zhu

AbstractMD simulations have been employed to investigate damage processes during keV bombardment of metal targets. For self-ion irradiations of Au, Cu, and Pt in the range of 5-20 keV, we have found that both the amount and the character of the damage created in the surface depends sensitively on the details of the energy deposition along individual ion trajectories. In all of these cases, significantly more damage is produced and more atomic mixing takes place relative to corresponding recoil events in the crystal interior. In some cases, enormous craters are formed in an explosive event, while in others a convective flow of atoms to the surface leaves dislocations behind. The results of these simulations will be summarized and their significance for damage studies of ion irradiated materials, discussed.


2001 ◽  
Vol 65 (2) ◽  
Author(s):  
S. Dhar ◽  
M. Milosavljevic ◽  
N. Bibic ◽  
K. P. Lieb

1994 ◽  
Vol 373 ◽  
Author(s):  
Eric Camus ◽  
Françise Bourdeau ◽  
Christian Abromeit ◽  
Nelja Wanderka ◽  
Heinrich Wollenberger

AbstractThe stability of the ordered γʹ precipitates under 300-keV Ni+ irradiation was investigated between room temperature and 623 K. The two competing mechanisms of destabilization by cascade producing irradiation, i. e. disordering and dissolution of the γʹ precipitates in Nimonic PE16 alloy, has been studied separately by electron microscopy and field-ion microscopy with atom probe. At high temperatures, the precipitates are stable. At intermediate temperatures, the precipitates dissolve by ballistic mixing into the matrix, but the interface is restored by the radiation-enhanced atomic jumps. The order in the precipitates remains stable. At low temperatures, the precipitates are dissolved by atomic mixing. The dissolution proceeds in a diffusional manner with a diffusion coefficient normalized by the displacement rate D/K = 0.75 nm2dpa−1. The precipitates become disordered by a fluence of 0.1 dpa, whereas precipitate dissolution needs much higher fluences.


2003 ◽  
Vol 76 (2) ◽  
pp. 165-169 ◽  
Author(s):  
B. Schattat ◽  
W. Bolse ◽  
S. Klaumünzer ◽  
F. Harbsmeier ◽  
A. Jasenek

1998 ◽  
Vol 527 ◽  
Author(s):  
L.C. Wei ◽  
E. Lang ◽  
M. Ghaly ◽  
P. Bellon ◽  
R. S. Averback

ABSTRACTThe temperature dependence of disordering of Cu3Au during ion irradiation has been investigated by computer simulations using MONTE CARLO methods. The investigation was motivated by peculiar experimental observations that the initial disordering rate begins to decrease above ~300 K, which can be explained by vacancies just becoming mobile at that temperature, but then at ~ 475 K, it reaches a minimum and then increases rapidly as the temperature is further increased, up to the order-disorder temperature. The present simulation shows that this behavior can be understood in terms of temperatures dependencies in both atomic mixing in the cascade and the efficiency of vacancy annealing of disorder as the vacancies diffuse out of the cascade.


Author(s):  
L. J. Chen ◽  
L. S. Hung ◽  
J. W. Mayer

When an energetic ion penetrates through an interface between a thin film (of species A) and a substrate (of species B), ion induced atomic mixing may result in an intermixed region (which contains A and B) near the interface. Most ion beam mixing experiments have been directed toward metal-silicon systems, silicide phases are generally obtained, and they are the same as those formed by thermal treatment.Recent emergence of silicide compound as contact material in silicon microelectronic devices is mainly due to the superiority of the silicide-silicon interface in terms of uniformity and thermal stability. It is of great interest to understand the kinetics of the interfacial reactions to provide insights into the nature of ion beam-solid interactions as well as to explore its practical applications in device technology.About 500 Å thick molybdenum was chemical vapor deposited in hydrogen ambient on (001) n-type silicon wafer with substrate temperature maintained at 650-700°C. Samples were supplied by D. M. Brown of General Electric Research & Development Laboratory, Schenectady, NY.


Sign in / Sign up

Export Citation Format

Share Document