scholarly journals Fiber quality and juvenile-mature transition evaluation of jabon (Anthocephalus cadamba) and binuang (Octomeles sumatrana)

2020 ◽  
Vol 591 ◽  
pp. 012009
Author(s):  
S D Marbun ◽  
I Wahyudi ◽  
J Suryana ◽  
D S Nawawi
Keyword(s):  
Fiber Quality ◽  
Anthocephalus Cadamba

Production, Fiber Quality, and Ginning Performance of Low and High Pubescent Pima Cotton 1

Crop Science ◽  
1978 ◽  
Vol 18 (2) ◽  
pp. 324-326
Author(s):  
E. F. Young ◽  
I. W. Kirk ◽  
Carl V. Feaster
Keyword(s):  
Fiber Quality ◽  
Pima Cotton

scholarly journals Color change and termite resistance of fast-growing tropical woods treated with kesambi (Schleichera oleosa) smoke

2020 ◽  
Vol 66 (1) ◽  
Author(s):  
Yusuf Sudo Hadi ◽  
Muh Yusram Massijaya ◽  
Dodi Nandika ◽  
Wa Ode Muliastuty Arsyad ◽  
Imam Busyra Abdillah ◽  
...  
Keyword(s):  
Color Change ◽  
Acacia Mangium ◽  
Chemical Compounds ◽  
Subterranean Termite ◽  
Subterranean Termites ◽  
Schleichera Oleosa ◽  
Termite Attack ◽  
Wood Resistance ◽  
Tropical Woods ◽  
Anthocephalus Cadamba

Abstract Smoke treatment can be used to enhance wood resistance to subterranean termite attack. In this study, kesambi (Schleichera oleosa) wood was pyrolyzed to produce charcoal. The smoke produced as a by-product of pyrolysis was used to treat sengon (Falcataria moluccana), jabon (Anthocephalus cadamba), mangium (Acacia mangium), and pine (Pinus merkusii) wood samples for 1, 2, or 3 weeks. Following the smoke treatment, the wood specimens were exposed to subterranean termites (Coptotermes curvignathus Holmgren) according to the Indonesian standard 7207-2014 in a laboratory. The color change caused by smoke treatment was observed, and chemical analysis of smoke was also done. The results showed that chemical compounds of kesambi smoke predominantly consisted of acetic acid, phenol, ketones, amines, and benzene. The color of smoked wood became darker, less yellow, and a little redder, while a longer smoking period produced a darker color which was more resistant to termite attack. Smoke treatment enhanced the resistance of wood to subterranean termite attack, and the resistance levels were not significantly different based on the duration of the smoke treatment.

Optimizing Irrigation and Plant Density for Improved Cotton Yield and Fiber Quality

2014 ◽  
Vol 106 (4) ◽  
pp. 1111-1118 ◽  
Author(s):  
Lu Feng ◽  
Garrett Mathis ◽  
Glen Ritchie ◽  
Yinchun Han ◽  
Yabing Li ◽  
...  
Keyword(s):  
Plant Density ◽  
Fiber Quality ◽  
Cotton Yield

Feasibility of High Speed Furnace Drawing of Optical Fibers

2004 ◽  
Vol 126 (5) ◽  
pp. 852-857 ◽  
Author(s):  
Xu Cheng ◽  
Yogesh Jaluria
Keyword(s):  
Optical Fibers ◽  
High Speed ◽  
Flow Instability ◽  
Fiber Quality ◽  
Domain Boundary ◽  
Operating Conditions ◽  
Furnace Temperature ◽  
Fiber Drawing ◽  
Heated Zone ◽  
Additional Information

The domain of operating conditions, in which the optical fiber-drawing process is successful, is an important consideration. Such a domain is mainly determined by the stresses acting on the fiber and by the stability of the process. This paper considers an electrical resistance furnace for fiber drawing and examines conditions for process feasibility. In actual practice, it is known that only certain ranges of furnace temperature and draw speed lead to successful fiber drawing. The results obtained here show that the length of the heated zone and the furnace temperature distribution are other important parameters that can be varied to obtain a feasible process. Physical behavior close to the boundary of the feasible domain is also studied. It is found that the iterative scheme for neck-down profile determination diverges rapidly when the draw temperature is lower than that at the acceptable domain boundary due to the lack of material flow. However, the divergence rate becomes much smaller as the temperature is brought close to the domain boundary. Additional information on the profile determination as one approaches the acceptable region is obtained. It is found that it is computationally expensive and time-consuming to locate the exact boundary of the feasible drawing domain. From the results obtained, along with practical considerations of material rupture, defect concentration, and flow instability, an optimum design of a fiber-drawing system can be obtained for the best fiber quality.

scholarly journals Selection of cotton lines for high oil content

2017 ◽  
Vol 52 (7) ◽  
pp. 530-538 ◽  
Author(s):  
Luiz Paulo de Carvalho ◽  
Josiane Isabela da Silva Rodrigues ◽  
Francisco José Correia Farias
Keyword(s):  
Oil Content ◽  
Genetic Parameters ◽  
Fiber Quality ◽  
Rio Grande ◽  
Field Trials ◽  
The State ◽  
The Other ◽  
Expected Gain ◽  
High Heritability ◽  
Selection Of

Abstract: The objective of this work was to evaluate the oil content and characters related to fiber quality and yield in cotton lines (Gossypium hirsutum), in order to select genotypes with high oil content and acceptable levels of the other characters. Twenty-two F6 lines and three checks were cultivated in three field trials - two in the municipality of Apodi, in the state of Rio Grande do Norte, and one in the municipality of Barbalha, in the state of Ceará, both in Brazil. The genetic parameters and the genetic gain from selecting 20% of the lines were estimated according to their means in each environment and in the group of environments. Regarding oil content, there is genetic variability, and the selection based on the overall mean is indicated, since this character showed high heritability, with 4.58% expected gain. The lines selected with this criterion have oil contents between 23.52 and 24.51%, which are higher than those of the Brazilian cultivar BRS Aroeira with the highest grain oil content (22.04%).

Sign in / Sign up

Export Citation Format

Share Document