scholarly journals Evaluation of Aspect Ratio on Tensile and Compressive Properties of Welded API X70 Steel

2021 ◽  
Vol 1107 (1) ◽  
pp. 012197
Author(s):  
O. I. Erinfolami ◽  
O. Adedipe
Keyword(s):  
Aspect Ratio ◽  
Compressive Properties

Compressive properties of bulk metallic glass with small aspect ratio

2007 ◽  
Vol 22 (2) ◽  
pp. 501-507 ◽  
Author(s):  
F.F. Wu ◽  
Z.F. Zhang ◽  
S.X. Mao
Keyword(s):  
Plastic Deformation ◽  
Aspect Ratio ◽  
Metallic Glass ◽  
Bulk Metallic Glass ◽  
Deformation Behavior ◽  
Shear Bands ◽  
Compressive Load ◽  
Small Aspect Ratio ◽  
Compressive Properties ◽  
Deformation Ability

The quasi-static compressive deformation behavior of a Vitreloy 1 bulk metallic glass (BMG) with an aspect ratio of 0.25 was investigated. It is found that the friction and the confinement at the specimen–loading platen interface will cause the dramatic increase in the compressive load, leading to higher compressive strength. In particular, the BMG specimens show great plastic-deformation ability, and plenty of interacted, deflected, wavy, or branched shear bands were observed on the surfaces after plastic deformation. The formation of the strongly interacted, deflected, wavy, or branched shear bands can be attributed to the triaxial stress state in the glassy specimens with a very small aspect ratio.

scholarly journals Test method development and determination of three-dimensional stiffness properties of polyvinyl chloride structural foams

2017 ◽  
Vol 52 (5) ◽  
pp. 679-688 ◽  
Author(s):  
Akira Miyase ◽  
Su Su Wang
Keyword(s):  
Aspect Ratio ◽  
Polyvinyl Chloride ◽  
Three Dimensional ◽  
Transversely Isotropic ◽  
Gage Section ◽  
Test Method ◽  
Compressive Properties ◽  
Stiffness Properties ◽  
Significant Difference ◽  
Out Of Plane

A study has been conducted to develop proper test methods and to utilize the tests to evaluate three-dimensional mechanical behavior of a polyvinyl chloride structural foam (Divinycell H80 with nominal density of 80 kg/m3). Transversely isotropic foam microstructure was examined and it revealed that the cell size aspect ratio in in-plane directions was near unity but greater than one in the out-of-plane (rise) direction. Foam stiffness properties, i.e. moduli and Poisson’s ratios, were obtained in different loading modes, along both in-plane and out-of-plane directions. The influence of test specimen geometry on compressive properties was studied. Foam specimens with both straight-side and reduced gage sections were designed, fabricated and tested. The effect of specimen gage-section aspect ratio was identified as a critical geometric parameter, affecting foam compressive properties. For foam tensile properties, specimens with different cross-sectional dimensions in the gage section were used. The results revealed transversely isotropic characteristics of the foam material. To evaluate foam shear properties a scaled shear test method was developed. The results indicated a significant difference in in-plane and out-of-plane foam shear stiffness properties.

Effects of specimen aspect ratio on the compressive properties of Mg alloy foam

2012 ◽  
Vol 42 ◽  
pp. 32-36 ◽  
Author(s):  
Xingchuan Xia ◽  
Weimin Zhao ◽  
Zhihao Wei ◽  
Zhiguo Wang
Keyword(s):  
Aspect Ratio ◽  
Mg Alloy ◽  
Compressive Properties

Modification of MnS inclusion by tellurium in 38MnVS6 micro-alloyed steel

2020 ◽  
Vol 117 (6) ◽  
pp. 615
Author(s):  
Ping Shen ◽  
Lei Zhou ◽  
Qiankun Yang ◽  
Zhiqi Zeng ◽  
Kenan Ai ◽  
...  
Keyword(s):  
Fatigue Life ◽  
Aspect Ratio ◽  
Strong Influence ◽  
Experimental Results ◽  
Alloyed Steel ◽  
Equivalent Diameter ◽  
Small Aspect Ratio ◽  
Steel Quality ◽  
Eds Analysis ◽  
Micro Alloyed Steel

In 38MnVS6 steel, the morphology of sulfide inclusion has a strong influence on the fatigue life and machinability of the steel. In most cases, the MnS inclusions show strip morphology after rolling, which significantly affects the steel quality. Usually, the MnS inclusion with a spherical morphology is the best morphology for the steel quality. In the present work, tellurium was applied to 38MnVS6 micro-alloyed steel to control the MnS inclusion. Trace tellurium was added into 38MnVS6 steel and the effect of Te on the morphology, composition, size and distribution of MnS inclusions were investigated. Experimental results show that with the increase of Te content, the equivalent diameter and the aspect ratio of inclusion decrease strikingly, and the number of inclusions with small aspect ratio increases. The inclusions are dissociated and spherized. The SEM-EDS analysis indicates that the trace Te mainly dissolves in MnS inclusion. Once the MnS is saturated with Te, MnTe starts to generate and wraps MnS. The critical Te/S value for the formation of MnTe in the 38MnV6 steel is determined to be approximately 0.075. With the increase of Te/S ratio, the aspect ratio of MnS inclusion decreases and gradually reaches a constant level. The Te/S value in the 38MnVS6 steel corresponding to the change of aspect ratio from decreasing to constant ranges from 0.096 to 0.255. This is most likely to be caused by the saturation of Te in the MnS inclusion. After adding Te in the steel, rod-like MnS inclusion is modified to small inclusion and the smaller the MnS inclusion, the lower the aspect ratio.

Adding an expansive agent to increase the toughness of steel fibre reinforced concrete

2019 ◽  
Vol 26 (4) ◽  
pp. 197-208
Author(s):  
Leo Gu Li ◽  
Albert Kwok Hung Kwan
Keyword(s):  
Reinforced Concrete ◽  
Steel Fibre ◽  
The Other ◽  
Fibre Reinforced Concrete ◽  
Test Results ◽  
Compressive Properties ◽  
Shrinkage Cracking ◽  
Steel Fibre Reinforced Concrete ◽  
Expansive Agent ◽  
Concrete Matrix

Previous research studies have indicated that using fibres to improve crack resistance and applying expansive agent (EA) to compensate shrinkage are both effective methods to mitigate shrinkage cracking of concrete, and the additions of both fibres and EA can enhance the other performance attributes of concrete. In this study, an EA was added to fibre reinforced concrete (FRC) to produce concrete mixes with various water/binder (W/B) ratios, steel fibre (SF) contents and EA contents for testing of their workability and compressive properties. The test results showed that adding EA would slightly increase the superplasticiser (SP) demand and decrease the compressive strength, Young’s modulus and Poisson’s ratio, but significantly improve the toughness and specific toughness of the steel FRC produced. Such improvement in toughness may be attributed to the pre-stress of the concrete matrix and the confinement effect of the SFs due to the expansion of the concrete and the restraint of the SFs against such expansion.

PENINGKATAN KEMAMPUAN GURU BAHASA INDONESIA DALAM MENYUSUN RENCANA PROGRAM PEMBELAJARAN (RPP) SDN 015 PAGARAN TAPAH DARUSSALAM MELALUI METODE PEMBERIAN TUGAS

2017 ◽  
Vol 5 (3) ◽  
pp. 713
Author(s):  
Mukhlis '
Keyword(s):  
Aspect Ratio ◽  
Duty Cycle ◽  
Lesson Plans ◽  
Learning Program ◽  
School Subjects ◽  
Bahasa Indonesia

Based on the observation of some teachers found the symptoms as follows: the lack of abilityof Indonesian teachers in designing learning program (RPP), the learning device is only usedas a supplement and not to the needs of teaching, most teachers again if asked the lessonanswered not have or has not been made. The purpose of this research is to improve theability of Indonesian teachers in designing learning program (RPP) at SDN 015 PagaranTapah Darussalam through the method of administration tasks. This type of research is actionresearch school. Subjects in this study were teachers Indonesian as many as 12 people. Basedon the analysis and discussion can be concluded that the method of administration tasks canimprove the ability of Indonesian teachers in making learning device in SDN 015 PagaranTapah Darussalam through the method of administration tasks. Under these conditions, thelevel of acceptance of teachers increased. The aspect ratio capability Indonesian teachers inpreparing lesson plans through the provision of duty cycle I and II of the increase from 56%and the second cycle to 79%.

Sign in / Sign up

Export Citation Format

Share Document