scholarly journals Parametric studies on floating pad journal bearing for high speed cryogenic turboexpanders

2017 ◽  
Vol 278 ◽  
pp. 012026
Author(s):  
A Jain ◽  
M M Jadhav ◽  
S Karimulla ◽  
A Chakravarty
Keyword(s):  
High Speed ◽  
Journal Bearing ◽  
Parametric Studies

scholarly journals Improvement of Tilting-Pad Journal Bearing Operating Characteristics by Application of Eddy Grooves

Lubricants ◽  
2021 ◽  
Vol 9 (2) ◽  
pp. 18
Author(s):  
Eckhard Schüler ◽  
Olaf Berner
Keyword(s):  
High Speed ◽  
Journal Bearing ◽  
Load Capacity ◽  
Fluid Film ◽  
Operating Characteristics ◽  
Fluid Film Bearings ◽  
Tilting Pad ◽  
Bearing Load ◽  
Bearing Loads ◽  
Tilting Pad Journal Bearing

In high speed, high load fluid-film bearings, the laminar-turbulent flow transition can lead to a considerable reduction of the maximum bearing temperatures, due to a homogenization of the fluid-film temperature in radial direction. Since this phenomenon only occurs significantly in large bearings or at very high sliding speeds, means to achieve the effect at lower speeds have been investigated in the past. This paper shows an experimental investigation of this effect and how it can be used for smaller bearings by optimized eddy grooves, machined into the bearing surface. The investigations were carried out on a Miba journal bearing test rig with Ø120 mm shaft diameter at speeds between 50 m/s–110 m/s and at specific bearing loads up to 4.0 MPa. To investigate the potential of this technology, additional temperature probes were installed at the crucial position directly in the sliding surface of an up-to-date tilting pad journal bearing. The results show that the achieved surface temperature reduction with the optimized eddy grooves is significant and represents a considerable enhancement of bearing load capacity. This increase in performance opens new options for the design of bearings and related turbomachinery applications.

Experimental Investigation on Cavitation Characteristics of a Three-Groove Journal Bearing

2013 ◽  
Vol 420 ◽  
pp. 47-50
Author(s):  
Ying Yang ◽  
Jing Hua Dai
Keyword(s):  
Experimental Investigation ◽  
High Speed ◽  
Journal Bearing ◽  
Rupture Zone ◽  
Work Characteristics ◽  
Oil Film ◽  
Rotating Speed ◽  
Clear Effect ◽  
Supply Pressure

Under high and super-high speed, oil film of the journal bearing is easy to crack and then becomes cavitation. The existence of cavitation has an important effect on the work characteristics of the shaft. On the journal bearing experiment rig the cavitation characteristics of the three-groove journal beaing were studied. The influences of the shaft rotating speed and supply pressure on cavitation shape were investigated. The results show that rotating speed and supply pressure have a clear effect on the cavitation shape, and the number of cavitation strip in the rupture zone decreases when the supply pressure increases.

Experimental Research on Cavitation Characteristics of a Novel Hybrid Journal Bearing

2013 ◽  
Vol 420 ◽  
pp. 74-77
Author(s):  
Ying Yang ◽  
Jing Hua Dai ◽  
Xu Li
Keyword(s):  
Experimental Research ◽  
High Speed ◽  
Work Performance ◽  
Journal Bearing ◽  
Rupture Zone ◽  
Oil Film ◽  
Rotating Speed ◽  
Supply Pressure ◽  
Experimental Rig

Under high and super high speed, the oil film of a journal bearing is easy to crack and then becomes cavitation. The existence of cavitation has a great effect on the work performance of the bearing. The cavitation mechanism of a spiral oil wedge journal bearing was investigated on the experimental rig. The effects of rotating speed and supply pressure on the cavitation shape of oil film and the number of cavitation strip in the rupture zone were analyzed. The results show that the cavitation shape of oil film is a long strip. The number of cavitation strip increases when supply pressure has been improved, and the location of oil outlet must be designed optimally.

Influence of geometric parameters and operating conditions on the thermohydrodynamic behaviour of plain journal bearings

2000 ◽  
Vol 214 (5) ◽  
pp. 445-457 ◽  
Author(s):  
I Pierre ◽  
M Fillon
Keyword(s):  
High Speed ◽  
Journal Bearing ◽  
Three Dimensional ◽  
Journal Bearings ◽  
Operating Conditions ◽  
Thermal Dissipation ◽  
Radial Clearance ◽  
Geometric Factors ◽  
Essential Components ◽  
Mass Flowrate

Hydrodynamic journal bearings are essential components of high-speed machinery. In severe operating conditions, the thermal dissipation is not a negligible phenomenon. Therefore, a three-dimensional thermohydrodynamic (THD) analysis has been developed that includes lubricant rupture and re-formation phenomena by conserving the mass flowrate. Then, the predictions obtained with the proposed numerical model are validated by comparison with the measurements reported in the literature. The effects of various geometric factors (length, diameter and radial clearance) and operating conditions (rotational speed, applied load and lubricant) on the journal bearing behaviour are analysed and discussed in order to inform bearing designers. Thus, it can be predicted that the bearing performance obtained highly depends on operating conditions and geometric configuration.

Experimental Study on Cavitation Boundary of Journal Bearing

2013 ◽  
Vol 378 ◽  
pp. 362-366
Author(s):  
Ying Yang ◽  
Li Xu ◽  
Wen Qing Liu
Keyword(s):  
Experimental Study ◽  
High Speed ◽  
Journal Bearing ◽  
Theory Model ◽  
Work Characteristics ◽  
Oil Film ◽  
Rotating Speed ◽  
Supply Pressure ◽  
Rupture Area ◽  
Experimental Rig

Under high and super-high speed conditions, oil film of the journal bearing is easy to crack and then becomes cavitation. The existence of cavitation has a great effect on the work characteristics of the bearing. Cavitation boundary of a three-groove journal beaing was investigated on the journal bearing experimental rig. The influences of rotating speed and supply pressure on cavitation boundary were studied. And experimental equations of reformation location and the percent of rupture area are established. The results show that rupture location of oil film is not related with rotating speed and supply pressure, otherwise reformation location of oil film is effected greatly by them. The experimental equations lay foundations for next research on cavitation theory model and stability.

The Granular Lubricated Journal Bearing: Evidence of Lift Formation

2019 ◽  
Vol 141 (4) ◽  
Author(s):  
Venkata K. Jasti ◽  
Martin C. Marinack ◽  
Deepak Patil ◽  
C. Fred Higgs
Keyword(s):  
Carrying Capacity ◽  
Granular Flow ◽  
High Speed ◽  
Journal Bearing ◽  
Hydrodynamic Lubrication ◽  
Flow Behavior ◽  
Extreme Environments ◽  
Granular Flows ◽  
Load Carrying Capacity ◽  
Load Carrying

This work demonstrates that granular flows (i.e., macroscale, noncohesive spheres) entrained into an eccentrically converging gap can indeed actually exhibit lubrication behavior as prior models postulated. The physics of hydrodynamic lubrication is quite well understood and liquid lubricants perform well for conventional applications. Unfortunately, in certain cases such as high-speed and high-temperature environments, liquid lubricants break down making it impossible to establish a stable liquid film. Therefore, it has been previously proposed that granular media in sliding convergent interfaces can generate load carrying capacity, and thus, granular flow lubrication. It is a possible alternative lubrication mechanism that researchers have been exploring for extreme environments, or wheel-regolith traction, or for elucidating the spreadability of additive manufacturing materials. While the load carrying capacity of granular flows has been previously demonstrated, this work attempts to more directly uncover the hydrodynamic-like granular flow behavior in an experimental journal bearing configuration. An enlarged granular lubricated journal bearing (GLJB) setup has been developed and demonstrated. The setup was made transparent in order to visualize and video capture the granular collision activity at high resolution. In addition, a computational image processing program has been developed to process the resulting images and to noninvasively track the “lift” generated by granular flow during the journal bearing operation. The results of the lift caused by granular flow as a function of journal rotation rate are presented as well.

Sign in / Sign up

Export Citation Format

Share Document