scholarly journals Establishment of the falling film evaporation model and correlation of the overall heat transfer coefficient

2019 ◽  
Vol 6 (5) ◽  
pp. 190135 ◽  
Author(s):  
Jing Fang ◽  
Kaixuan Li ◽  
Mengyu Diao
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Temperature Distribution ◽  
Film Thickness ◽  
Liquid Film ◽  
Velocity Distribution ◽  
Transfer Coefficient ◽  
Falling Film ◽  
Overall Heat Transfer Coefficient ◽  
Proposed Model

In order to study the heat transfer of the falling film evaporator with phase change on both sides, in this paper we built the mathematical model and the physical model where the liquid film inside the tube is laminar and turbulent. The film thickness of the condensate at different axial positions, total condensate volume and velocity distribution, and temperature distribution of condensate outside the tube can be obtained by calculating the proposed model. Meanwhile, the liquid film thickness, velocity distribution and temperature distribution inside the tube were obtained by numerical simulation by considering the influence of the liquid film with different compositions on the heat transfer during fluid flow. With ethanol–water as the system, the overall heat transfer coefficient and heat transfer quantity of the falling film evaporator were obtained by the calculation of the model. The accuracy of the proposed model was confirmed by experiments. The model and the calculation of heat transfer proposed in this paper have enormous significance for the basic data and theoretical guidance of the heat transfer performance prediction and operational optimization of the evaporator.

scholarly journals Heat-transfer characteristics of ammonia-water falling film generation outside a vertical tube

2017 ◽  
Vol 21 (3) ◽  
pp. 1251-1259 ◽  
Author(s):  
Chao Luo ◽  
Jun Zhao ◽  
Weibin Ma
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Water Temperature ◽  
Water Solution ◽  
Hot Water ◽  
Falling Film ◽  
Ammonia Water ◽  
Overall Heat Transfer Coefficient ◽  
Spray Density

A heat transfer experimental of vertical out-tube falling film was conducted with different inlet spray density of ammonia-water solution and inlet hot water temperature. The inlet liquid mass concentration was selected as 60% of ammonia. The experiments showed that the overall heat transfer coefficient increases with the increase of inlet spray density and a maximum overall heat transfer coefficient could be obtained in an optimum spray density of ammonia-water solution, ?, between 0.26 and 0.29 kg/ms. The generation of ammonia vapor outside the vertical falling film had a similar trend with the overall heat transfer coefficient basing on different spray density. The effect of hot water temperature difference, ?T, on overall heat transfer coefficient showed that ?T between 10 and 13 K is the optimum temperature difference of the vertical falling film generation

Simulation of Sweating/Evaporation Boosted Convective Heat Transfer Under Laminar Flow Condition

2017 ◽  
Author(s):  
Sudipta Saha ◽  
Rajib Mahamud ◽  
Jamil Khan ◽  
Tanvir Farouk
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Reynolds Number ◽  
Heat Transfer Coefficient ◽  
Laminar Flow ◽  
Film Thickness ◽  
Liquid Film ◽  
Transfer Coefficient ◽  
Water Film ◽  
The Heat Transfer Coefficient

Phase change driven heat transfer has been the topic of interest for a significantly long time. However, in recent years on demand sweating boosted evaporation which requires substantially less amount of the liquid medium has drawn attention as a possible way of increasing/supplementing heat transfer under convective conditions where the convective heat transfer coefficient has already reached its maximum value as well as where dry cooling is a desired objective. In this study, a numerical study is conducted to obtain insight into the ‘hybrid’ system where evaporation and convection both contribute to the heat transfer effect. The system modeled consists of evaporation of thin liquid (water) film under a laminar flow condition. The mathematical model employed consists of coupled conservation equations of mass, species, momentum and energy for the convection-evaporation domain (gaseous), with only mass and energy conservation being resolved in the liquid film domain. The evaporative mass flux is obtained from a modified Hertz-Knudsen relation which is a function of liquid-vapor interface temperature and pressure. A two-dimensional rectangular domain with a pre-prescribed thin liquid water film representative of an experiment is simulated with the developed model. The thin rectangular liquid film is heated by uniform heat flux and is placed in the convection-evaporation domain with an unheated starting length. A moving boundary mesh is applied via the“Arbitrary Lagrangian-Eulerian” technique to resolve the receding liquid interface resulting from evaporation. The prescribed relative displacement of the moving interface is calculated from the net mass flux due to evaporation and is governed by the principle of mass conservation. Simulations were conducted over a range of Reynolds number, heat flux conditions and liquid film thickness. The numerical predictions indicate that under convective-evaporative conditions the overall heat transfer coefficient increases significantly (∼factor of a five) in comparison to the purely forced convection scenario. An increase in the heat transfer coefficient is observed with Reynolds number and vice versa for film thickness. A critical Reynolds number is identified beyond which the heat transfer coefficient does not continue to increase significantly rather tends to plateau out.

Heat Transfer Coefficient in Falling Film Evaporators With Different Tube Arrangements

2012 ◽  
Author(s):  
Shengqiang Shen ◽  
Gangtao Liang ◽  
Yali Guo ◽  
Xingsen Mu ◽  
Rui Liu ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Temperature Difference ◽  
Saturation Temperature ◽  
Horizontal Tube ◽  
Falling Film ◽  
Overall Heat Transfer Coefficient ◽  
Spray Density ◽  
Total Temperature

A set of experimental facilities were set up to measure overall heat transfer coefficient of horizontal-tube falling film evaporators with triangular, rotated square and square-pitch bundles. Effect of spray density, saturation temperature, total temperature difference and inlet steam velocity on the overall heat transfer coefficient K is studied respectively. The tubes are made of HAL77-2A aluminium brass with an outer diameter of 25.4 mm. Fluids inside and outside the tubes are steam and fresh water respectively. The results indicate that growth of spray density and saturation temperature helps to increase the K. The K could also be increased by reducing the total temperature difference. However, the impact of the inlet steam velocity on the K is less significant. The K in the evaporator with rotated square-pitch arrangement is supreme. Furthermore, space distribution of local overall heat transfer coefficient K̃ in the evaporators is also discussed. Based on this investigation, basic engineering design information will be provided to establish the governing parameters for horizontal-tube falling film evaporator in the field of seawater desalination.

scholarly journals Interfacial waviness during condensation heat transfer

2021 ◽  
Vol 2116 (1) ◽  
pp. 012014
Author(s):  
A Berto ◽  
P Lavieille ◽  
M Azzolin ◽  
S Bortolin ◽  
M Miscevic ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Film Thickness ◽  
Liquid Film ◽  
Transfer Coefficient ◽  
Liquid Film Thickness ◽  
Condensation Heat Transfer ◽  
Internal Diameter ◽  
Transfer Coefficients ◽  
Two Phase

Abstract Heat transfer coefficients and liquid film thickness have been measured during convective condensation inside a 3.4 mm internal diameter channel. Condensation tests have been run with refrigerant R245fa during vertical downflow at mass velocity equal to 50 kg m-2 s-1 and 100 kg m-2 s-1. The test section is composed of two heat exchangers for the measurement of the heat transfer coefficient connected by means of a glass tube designed for the visualization of the two-phase flow patterns and for the measurement of the liquid film thickness. The liquid film thickness is determined by coupling a shadowgraph technique and chromatic confocal measurements. The measured values of heat transfer coefficient and liquid film thickness are reported and analysed together to investigate the effect of waves on the condensation heat transfer mechanisms.

scholarly journals A numerical model and validation of phase change material integrated thermoelectric radiant cooling panel

2019 ◽  
Vol 111 ◽  
pp. 01001
Author(s):  
Hansol Lim ◽  
Hye-Jin Cho ◽  
Seong-Yong Cheon ◽  
Soo-Jin Lee ◽  
Jae-Weon Jeong
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Numerical Model ◽  
Surface Temperature ◽  
Phase Change ◽  
Transfer Coefficient ◽  
Phase Change Material ◽  
Overall Heat Transfer Coefficient ◽  
Radiant Cooling ◽  
Change Material

A phase change material based radiant cooling panel with thermoelectric module (PCM-TERCP) is proposed in this study. It consists of two aluminium panels, and phase change materials (PCMs) sandwiched between the two panels. Thermoelectric modules (TEMs) are attached to one of the aluminium panels, and heat sinks are attached to the top side of TEMs. PCM-TERCP is a thermal energy storage concept equipment, in which TEMs freeze the PCM during the night whose melting temperature is 16○C. Therefore, the radiant cooling panel can maintain a surface temperature of 16◦C without the operation of TEM during the day. Furthermore, it is necessary to design the PCM-TERCP in a way that it can maintain the panel surface temperature during the targeted operating time. Therefore, the numerical model was developed using finite difference method to evaluate the thermal behaviour of PCM-TERCP. Experiments were also conducted to validate the performance of the developed model. Using the developed model, the possible operation time was investigated to determine the overall heat transfer coefficient required between radiant cooling panel and TEM. Consequently, the results showed that a overall heat transfer coefficient of 394 W/m2K is required to maintain the surface temperature between 16○C to 18○C for a 3 hours operation.

Sign in / Sign up

Export Citation Format

Share Document