Bright interior of nuclei viewed by α particles: High order eikonal expansion

The low Z metal aluminium is a potential matrix material for the first wall in fusion reactors. A drawback in the application of A1 is the rel= atively high amount of He produced in it under fusion reactor conditions. Knowledge about the behaviour of He during irradiation and deformation in Al, especially near the surface, is therefore important.Using the TEM we have studied Al disks of 3 mm diameter and 0.2 mm thickness, which were perforated at the centre by double jet polishing. These disks were bombarded at∽200°C to various doses with α-particles, impinging at any angle and energy up to 1.5 MeV at both surfaces. The details of the irradiations are described in Ref.1. Subsequent observation indicated that in such specimens uniformly distributed He-bubbles are formed near the surface in a layer several μm thick (Fig.1).After bombardment the disks were deformed at 20°C during observation by means of a tensile device in a Philips EM 300 microscope.

Download Full-text

Determination of the Burgers vector of a dislocation in a Fe-Mn alloy by weak-beam image in HVEM

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100108799 ◽

1978 ◽

Vol 36 (1) ◽

pp. 330-331

Author(s):

Y. Ishida ◽

H. Ishida ◽

K. Kohra ◽

H. Ichinose

Keyword(s):

High Order ◽

Simulation Technique ◽

The Other ◽

Image Simulation ◽

Diffraction Vector ◽

Burgers Vector ◽

Weak Beam ◽

Beam Image ◽

Edge Component

IntroductionA simple and accurate technique to determine the Burgers vector of a dislocation has become feasible with the advent of HVEM. The conventional image vanishing technique(1) using Bragg conditions with the diffraction vector perpendicular to the Burgers vector suffers from various drawbacks; The dislocation image appears even when the g.b = 0 criterion is satisfied, if the edge component of the dislocation is large. On the other hand, the image disappears for certain high order diffractions even when g.b ≠ 0. Furthermore, the determination of the magnitude of the Burgers vector is not easy with the criterion. Recent image simulation technique is free from the ambiguities but require too many parameters for the computation. The weak-beam “fringe counting” technique investigated in the present study is immune from the problems. Even the magnitude of the Burgers vector is determined from the number of the terminating thickness fringes at the exit of the dislocation in wedge shaped foil surfaces.

Download Full-text

The usefulness of high index low symmetry zone axes for holz line analysis

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100126718 ◽

1987 ◽

Vol 45 ◽

pp. 384-385

Author(s):

C. M. Sung ◽

D. B. Williams

Keyword(s):

Lattice Parameter ◽

High Order ◽

Zone Axis ◽

High Index ◽

High Symmetry ◽

Second Phases ◽

Line Patterns ◽

Low Symmetry ◽

Line Analysis

Researchers have tended to use high symmetry zone axes (e.g. <111> <114>) for High Order Laue Zone (HOLZ) line analysis since Jones et al reported the origin of HOLZ lines and described some of their applications. But it is not always easy to find HOLZ lines from a specific high symmetry zone axis during microscope operation, especially from second phases on a scale of tens of nanometers. Therefore it would be very convenient if we can use HOLZ lines from low symmetry zone axes and simulate these patterns in order to measure lattice parameter changes through HOLZ line shifts. HOLZ patterns of high index low symmetry zone axes are shown in Fig. 1, which were obtained from pure Al at -186°C using a double tilt cooling holder. Their corresponding simulated HOLZ line patterns are shown along with ten other low symmetry orientations in Fig. 2. The simulations were based upon kinematical diffraction conditions.

Download Full-text

Are HOLZ lines kinematic in off-zone-axis orientation?

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100149295 ◽

1993 ◽

Vol 51 ◽

pp. 692-693

Author(s):

J. M. Zuo ◽

A. L. Weickenmeier ◽

R. Holmestad ◽

J. C. H. Spence

Keyword(s):

Structure Determination ◽

Standard Procedure ◽

High Order ◽

Zone Axis ◽

Great Promise ◽

Line Position ◽

Measured Intensity ◽

Constant Intensity ◽

Axis Orientation ◽

Diffraction Condition

The application of high order reflections in a weak diffraction condition off the zone axis center, including those in high order laue zones (HOLZ), holds great promise for structure determination using convergent beam electron diffraction (CBED). It is believed that in this case the intensities of high order reflections are kinematic or two-beam like. Hence, the measured intensity can be related to the structure factor amplitude. Then the standard procedure of structure determination in crystallography may be used for solving unknown structures. The dynamic effect on HOLZ line position and intensity in a strongly diffracting zone axis is well known. In a weak diffraction condition, the HOLZ line position may be approximated by the kinematic position, however, it is not clear whether this is also true for HOLZ intensities. The HOLZ lines, as they appear in CBED patterns, do show strong intensity variations along the line especially near the crossing of two lines, rather than constant intensity along the Bragg condition as predicted by kinematic or two beam theory.

Download Full-text