burgers vector
Recently Published Documents


TOTAL DOCUMENTS

335
(FIVE YEARS 25)

H-INDEX

27
(FIVE YEARS 2)

2021 ◽  
Vol 9 ◽  
Author(s):  
Tiantian Shi ◽  
Wenbo Liu ◽  
Zhengxiong Su ◽  
Xu Yan ◽  
Chenyang Lu ◽  
...  

In the present study, the Fe-9Cr model alloy was irradiated with 240 keV He2+ at 550°C with a dose of 0.5 dpa at the peak damage region. The depth distribution of bubbles in Fe-9Cr alloy was investigated by transmission electron microscopy (TEM). The experimental results revealed that the spatial distribution of bubbles along the depth is different. In the region with higher helium concentration and irradiation dose, the bubbles inclined to be situated inside the plane of loops, forming a structure of “bubble-loop complex.” However, in regions where the helium concentration and irradiation dose are relatively low, the number of “bubble-loop complexes” significantly decreased. In addition, the Burgers vector of “bubble-loop complexes” was identified as <100> type. Radiation-induced enrichment of Cr atoms at the “bubble-loop complexes” was also quantitatively estimated by energy-dispersive X-ray spectroscopy (EDS) in the scanning TEM mode.


2021 ◽  
Author(s):  
John Wheeler ◽  
Sandra Piazolo ◽  
David Prior ◽  
Jake Tielke ◽  
Pat Trimby

<p>In many parts of the Earth rocks deform by dislocation creep. There is therefore a need to understand which slip systems operated in nature and in experimental products. Knowing the conditions of experiments may then allow natural conditions and strain rates to be characterised. Dislocation creep typically gives lattice preferred orientations (LPOs), since activity on particular slip systems leads to lattice rotations and alignment. For decades LPOs, measured first optically and since the 1990s by EBSD, have been used to infer slip systems. This is a valuable technique but the link between slip sytem activity and LPO is complicated, especially if recrystallisation and/or grain boundary sliding have been involved.</p><p>Here we present a more direct method to deduce “geometrically necessary” dislocations (GNDs) from the distortions within crystals. Distortions may be optically visible (e.g. undulose extinction in quartz) but EBSD has revealed how common distortions are, and allowed them to be quantified. The method does not give the complete picture of GNDs but allows hypotheses to be tested about possible slip systems. We illustrate this “Weighted Burgers Vector” method with a number of examples. In olivine the method distinguishes slip parallel to a and c, and in plastically deformed plagioclase it reveals a variety of slip systems which would be difficuilt to deduce from LPOs alone. GNDs may not necessarily reflect the full slip system activity, since many dislocations will have passed through crystals and merged with grain boundaries leaving no signature. Neverthless the method highlights what dislocations are present “stranded” in the microstructure. In many case these will have been produced by deformation although the method can also characterise growth defects.</p><p>Wheeler et al. 2009. The weighted Burgers vector: a new quantity for constraining dislocation densities and types using electron backscatter diffraction on 2D sections through crystalline materials. <span>DOI:</span> 10.1111/j.1365-2818.2009.03136.x</p>


2021 ◽  
Vol 22 (S3) ◽  
pp. 1-12
Author(s):  
Srinivasan Mahendran ◽  
Philippe Carrez ◽  
Patrick Cordier

2021 ◽  
Vol 83 (2) ◽  
pp. 198-206
Author(s):  
G.F. Sarafanov

A problem related to the development of instability of a homogeneous state in an ensemble of screw dislocations under plastic deformation of metals is considered . The study of the development of instability and structure formation in the dislocation ensemble is carried out on the basis of the method developed for charged particles in plasma and associated with the correlation interaction of electrons and positively charged ions. Accordingly, the screw dislocation ensemble is represented as a system of dislocations with an opposite Burgers vector, i.e., as a plasma-like medium with opposite dislocation charges. The total dislocation charge of the dislocation ensemble is equal to zero due to the law of conservation of the Burgers vector. In this situation, the elastic field of dislocations is “cut off”. The stress field of a single dislocation is shielded by a uniformly distributed dislocation “background” and is characterized by a certain effective potential. It is found that at long distances it decreases exponentially. Therefore, the value in the argument of the falling potential can be considered as the radius of screening of the elastic field of dislocations. It is shown that the screening radius is equal to the correlation radius, which makes it possible to construct a two-particle correlation function and find the energy of the correlation interaction of dislocations. A system of kinetic equations for a dislocation ensemble is formulated, taking into account the elastic and correlation interaction of dislocations, as well as the processes of their generation and annihilation. The criterion of instability of the homogeneous distribution of dislocations for the formulated system of equations is established. The instability criterion is met under the condition that the dislocation density exceeds a certain critical value that depends on the square of the flow stress and material constants (such as the Burgers vector modulus and shear modulus, as well as indirectly, the packing defect energy). In the framework of linear analysis, it is shown that when one system of sliding screw dislocations is taken into account, a one – dimensional periodic dislocation dissipative structure is formed at the moment of instability occurrence, and when multiple sliding is taken into account, solutions appear in the form of various variants of polyhedral lattices (cellular structures). It is established that the characteristic size of the cellular structure coincides with the experimental dependence both qualitatively and quantitatively ( the cell size is proportional to the square root of the dislocation density, and the proportionality coefficient is about ten). It is shown that the origin of spatially inhomogeneous dislocation structures, based on correlation instability, depends mainly on the features of the elastic interaction of dislocations and is not critical to the choice of the mechanisms of their kinetics (i.e., the mechanisms of generation, annihilation, and runoff of dislocations).


RSC Advances ◽  
2021 ◽  
Vol 11 (14) ◽  
pp. 7897-7902
Author(s):  
Bo Yu ◽  
Longyun Xu ◽  
Shenglai Wang ◽  
Pingping Huang ◽  
Hui Liu ◽  
...  

We modified the conventional etching-optical method to measure dislocation direction in a KDP crystal.


2021 ◽  
Vol 81 (1) ◽  
Author(s):  
F. L. Carneiro ◽  
S. C. Ulhoa ◽  
J. W. Maluf ◽  
J. F. da Rocha-Neto

AbstractWe consider non-linear plane gravitational waves as propagating space-time defects, and construct the Burgers vector of the waves. In the context of classical continuum systems, the Burgers vector is a measure of the deformation of the medium, and at a microscopic (atomic) scale, it is a naturally quantized object. One purpose of the present article is ultimately to probe an alternative way on how to quantize plane gravitational waves.


Crystals ◽  
2020 ◽  
Vol 10 (11) ◽  
pp. 1009
Author(s):  
Yutaka Ohno ◽  
Yuta Kubouchi ◽  
Hideto Yoshida ◽  
Toshio Kochiya ◽  
Tomio Kajigaya

The origin of twinning during the Czochralski (CZ) growth of 36°-RY lithium tantalate (LiTaO3) single crystals is examined, and it is shown that lineages composed of dislocation arrays act as an initiation site for twinning. Two types of lineages expand roughly along three different {12¯10} planes and two different {11¯00} planes. The former lineages and some latter lineages are composed of two types of mixed-dislocations with different Burgers vectors, while the other lineages are composed of only one type of edge-dislocation. All the dislocations have the Burgers vector of ⟨12¯10⟩ type with the compression side at the +Z side. Twin lamellae on {101¯2} are generated at a lineage during the CZ growth. We have hypothesized that dislocations in the lineage with b = 1/3⟨12¯10⟩ change their extension direction along a slip plane of {101¯2}, and they dissociate into pairs of partial dislocations with b = 1/6⟨22¯01⟩and 1/6⟨02¯21¯⟩ forming twin lamellae on {101¯2}.


2020 ◽  
Vol 51 (9) ◽  
pp. 4414-4421
Author(s):  
Bijin Zhou ◽  
Leyun Wang ◽  
Wenjun Liu ◽  
Xiaoqin Zeng ◽  
Yanjun Li

Abstract A method was proposed in this study to reveal the subsurface basal dislocation activity in Mg-Y alloy and determine the corresponding Burgers vector. This is achieved by correlating the slip directions of dislocations to the lattice rotation represented by the {0001} pole figure. The identified basal slip system by this approach was verified by micro-Laue diffraction. This method can be applied as a complementary method to the conventional slip trace analysis to study the dislocation behavior of Mg alloys.


Sign in / Sign up

Export Citation Format

Share Document