Providing a model for Csf according to pool boiling convection heat transfer of water/ferrous oxide nanofluid using sensitivity analysis

2019 ◽  
Vol 30 (6) ◽  
pp. 2867-2881 ◽  
Author(s):  
Mohammad Reza Salimpour ◽  
Mohammad Hossein Karimi Darvanjooghi ◽  
Ali Abdollahi ◽  
Arash Karimipour ◽  
Marjan Goodarzi
Keyword(s):  
Heat Transfer ◽  
Sensitivity Analysis ◽  
Surface Roughness ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Convection Heat Transfer ◽  
Content Type ◽  
Volume Fractions ◽  
Wall Superheat ◽  
Nanoparticles Concentration

Purpose A boiling surface with different initial roughness and under various nanoparticles volume fractions was studied in present work. Design/methodology/approach Develop a correlation and sensitivity analysis. Findings The results showed that for small (7.3 nm) and much larger (about 2,000 nm) surface roughness, compared to nanoparticle size of around 25 nm, the heat transfer rate of nanofluid diminishes relative to that of base fluid. The results also demonstrated that the boiling heat transfer rate is reduced by increasing the concentration of nanoparticles. For larger boiling surface roughness (480 nm) and nanoparticles volume fractions of less than 0.1 Vol.%, the value of heat transfer increases with the increase of nanoparticles concentration; and for those of more than 0.1 Vol.%, heat transfer rate decreases by adding more nanoparticles, significantly. Originality/value Finally, an equation was presented for estimating the wall superheat and the Csf coefficient in terms of mentioned parameters.

The impacts of non-uniform magnetic field on free convection heat transfer of a magnetizable micropolar nanofluid

2019 ◽  
Vol 29 (10) ◽  
pp. 3685-3706
Author(s):  
Zafar Namazian ◽  
S.A.M. Mehryan
Keyword(s):  
Heat Transfer ◽  
Free Convection ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Volume Fraction ◽  
Convection Heat Transfer ◽  
Content Type ◽  
Viscosity Parameter ◽  
Micropolar Nanofluid ◽  
Free Convection Heat

Purpose The purpose of this study is to numerically study the heat transfer of free convection of a magnetizable micropolar nanofluid inside a semicircular enclosure. Design/methodology/approach The flow domain is under simultaneous influences of two non-uniform magnetic fields generated by current carrying wires. The directions of the currents are the same. Although the geometry is symmetric, it is physically asymmetric. The impacts of key parameters, including Rayleigh number Ra = 103-106, Hartman number Ha = 0-50, vortex viscosity parameter Δ = 0-4, nanoparticles volume fraction φ = 0-0.04 and magnetic number Mnf = 0-1000, on the macro- and micro-scales flows, temperature and heat transfer rate are studied. Finding The outcomes show that dispersing of the nanoparticles in the host fluid increases the strength of macro- and micro-scale flows. When Mnf = 0, the increment of the vortex viscosity parameter increases the strength of the particles micro-rotations, while this characteristic is decreased by growing Δ for Mnf ≠ 0. The increment of Δ and Ha decreases the rate of heat transfer. The increment of Ha decreases the enhancement percentage of heat transfer rate because of dispersing nanoparticles, known as En parameter. In addition, the value of Δ has no effect on En. Moreover, the average Nusselt number Nuavg and En remain constant by increasing the magnetic number Mnf for different volume fraction values. Originality/value The authors believe that all of the results, both numerical and asymptotic, are original and have not been published elsewhere yet.

3D natural convection on a horizontal and vertical thermally active plate in a closed cubical cavity

2016 ◽  
Vol 26 (8) ◽  
pp. 2528-2542 ◽  
Author(s):  
Abimanyu Purusothaman ◽  
Abderrahmane Baïri ◽  
Nagarajan Nithyadevi
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Convection Heat Transfer ◽  
Numerical Code ◽  
Heated Plate ◽  
Algebraic Equations ◽  
Content Type ◽  
Cubical Cavity

Purpose The purpose of this paper is to examine numerically the natural convection heat transfer in a cubical cavity induced by a thermally active plate. Effects of the plate size and its orientation with respect to the gravity vector on the convective heat transfer and the flow structures inside the cavity are studied and highlighted. Design/methodology/approach The numerical code is based on the finite volume method with semi-implicit method for pressure-linked equation algorithm. The convective and diffusive terms in momentum equations are handled by adopting the power law scheme. Finally, the discretized sets of algebraic equations are solved by the line-by-line tri-diagonal matrix algorithm. Findings The results show that plate orientation and size plays a significant role on heat transfer. Also, the heat transfer rate is an increasing function of Rayleigh number for both orientations of the heated plate. Depending on the thermal management of the plate and its application (as in electronics), the heat transfer rate is maximized or minimized by selecting appropriate parameters. Research limitations/implications The flow is assumed to be 3D, time-dependent, laminar and incompressible with negligible viscous dissipation and radiation. The fluid properties are assumed to be constant, except for the density in the buoyancy term that follows the Boussinesq approximation. Originality/value The present work will give some additional knowledge in designing sealed cavities encountered in some engineering applications as in aeronautics, automobile, metallurgy or electronics.

Natural Convection Heat Transfer With Horizontal Rectangular Fin Array Using Straight Knurling Patterns on Fins: An Experimental Study

2018 ◽  
Author(s):  
R. C. Chikurde ◽  
B. S. Kothavale ◽  
N. K. Sane
Keyword(s):  
Heat Transfer ◽  
Surface Roughness ◽  
Natural Convection ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Convection Heat Transfer ◽  
Flow Characteristics ◽  
Natural Convection Heat Transfer ◽  
Convection Heat ◽  
Heat Transfer Augmentation

Natural Convection heat transfer from horizontal rectangular fin array with various knurling patterns is studied experimentally to find the effect of varying surface roughness on the heat transfer rate. The experimental parametric study is performed to investigate the effect of knurl produced surface roughness of fin on heat transfer rate. The parameters like knurling height from base, knurling depth and fin spacing might affect the flow characteristics and hence it is investigated to find the effect on heat transfer coefficient. The knurling is usually accomplished using one or more very hard rollers that contain the reverse of the pattern to be imposed. The result of this study shows that there are some important geometric factors related to knurling affecting the design of fin arrays and also heat transfer augmentation of natural convection heat transfer is observed.

Numerical analysis of mixed convection of different nanofluids in concentric annulus

2019 ◽  
Vol 29 (4) ◽  
pp. 1506-1525 ◽  
Author(s):  
Ahad Abedini ◽  
Saeed Emadoddin ◽  
Taher Armaghani
Keyword(s):  
Heat Transfer ◽  
Mixed Convection ◽  
Flow Pattern ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Volume Fraction ◽  
Convection Heat Transfer ◽  
Simple Algorithm ◽  
Content Type ◽  
Volume Method

Purpose This study aims to investigate the numerical analysis of mixed convection within the horizontal annulus in the presence of water-based fluid with nanoparticles of aluminum oxide, copper, silver and titanium oxide. Numerical solution is performed using a finite-volume method based on the SIMPLE algorithm, and the discretization of the equations is generally of the second order. Inner and outer cylinders have a constant temperature, and the inner cylinder temperature is higher than the outer one. The two cylinders can be rotated in both directions at a constant angular velocity. The effect of parameters such as Rayleigh, Richardson, Reynolds and the volume fraction of nanoparticles on heat transfer and flow pattern are investigated. The results show that the heat transfer rate increases with the increase of the Rayleigh number, as well as by increasing the volume fraction of the nanoparticles, the heat transfer rate increases, and this increase is about 8.25 per cent for 5 per cent volumetric fraction. Rotation of the cylinders reduces the overall heat transfer. Different directions of rotation have a great influence on the flow pattern and isotherms, and ultimately on heat transfer. The addition of nanoparticles does not have much effect on the flow pattern and isotherms, but it is quantitatively effective. The extracted results are in good agreement with previous works. Design/methodology/approach Studying mixed convection heat transfer in the horizontal annulus in the presence of a water-based fluid with aluminum oxide, copper, silver and titanium oxide nanoparticles is carried out quantitatively using a finite-volume method based on the SIMPLE algorithm. Findings Increasing the Rayleigh number increases the Nusselt number. Increasing the Richardson number increases heat transfer. Adding nanoparticles does not have much effect on the flow pattern but is effective quantitatively on heat transfer parameters. The addition of nanoparticles sometimes increases the heat transfer rate by about 8.25 per cent. In constant Rayleigh numbers, increasing the Reynolds number reduces heat transfer. The Rayleigh and Reynolds numbers greatly affect the isotherms and streamlines. In addition to the thermal conductivity of nanoparticles, the thermo-physical properties of nanoparticles has great effect in the formation of isotherms and streamlines and ultimately heat transfer. Originality/value Studying the effect of different direction of rotation on the isotherms and streamlines, as well as the comparison of different nanoparticles on mixed convection heat transfer in annulus.

Manninen’s mixture model for conjugate conduction and mixed convection heat transfer of a nanofluid in a rotational/stationary circular enclosure

2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Faraz Hoseininejad ◽  
Saeed Dinarvand ◽  
Mohammad Eftekhari Yazdi
Keyword(s):  
Heat Transfer ◽  
Mixed Convection ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Volume Fraction ◽  
Convection Heat Transfer ◽  
Convection Heat ◽  
Content Type ◽  
Mixed Convection Heat Transfer ◽  
Conjugate Conduction

Purpose This study aims to investigate numerically the problem of conjugate conduction and mixed convection heat transfer of a nanofluid in a rotational/stationary circular enclosure using a two-phase mixture model. Design/methodology/approach Hot and cold surfaces on the wall or inside the enclosure (heater and cooler) are maintained at constant temperature of Th and Tc, respectively, whereas other parts are thermally insulated. To examine the effects of various parameters such as Richardson number (0.01 = Ri =100), thermal conductivity ratio of solid to base fluid (1 = Kr = 100), volume fraction of nanoparticle (0 = φ = 0.05), insertion of conductive covers (C.Cs) around the heater in a different shape (triangular, circular or square), segmentation and arrangement of the conductive blocks (C.Bs) and rotation direction of the enclosure on the flow structure and heat transfer rate, two-dimensional equations of mass, momentum and energy conservation, as well as volume fraction, are solved using finite volume method and Semi-Implicit Method for Pressure Linked Equations (SIMPLE) algorithm. Findings The results show that inserting C.C around heater can increase or decrease heat transfer rate, and it depends on thermal conductivity ratio of solid to pure fluid. Also, it is found that by the division of C.B and location of its portions in a horizontal configuration, heat transfer rate reduces. Moreover, it is observed that external heating and cooling of the enclosure causes enhancement of heat transfer relative to that of internal heating and cooling. Finally, results illustrate that under the condition that cylinders rotate in the same direction, the heat transfer rate increases as compared to those that rotate in the opposite direction. Hence rotation direction of cylinders can be used as a desired parameter for controlling heat transfer rate. Originality/value A comprehensive report of results for the problem of conjugate conduction and mixed convection heat transfer in a circular cylinder containing different shapes of C.C, conducting obstacle and heater and cooler has been presented. An efficient numerical technique has been developed to solve this problem. The achievements of this paper are purely original, and the numerical results were never published by any researcher.

Effect of magnetic field-dependent thermal conductivity on natural convection of magnetic nanofluid inside a square enclosure

2019 ◽  
Vol 29 (4) ◽  
pp. 1466-1489 ◽  
Author(s):  
Mohammadhossein Hajiyan ◽  
Shohel Mahmud ◽  
Mohammad Biglarbegian ◽  
Hussein A. Abdullah ◽  
A. Chamkha
Keyword(s):  
Magnetic Field ◽  
Heat Transfer ◽  
Thermal Conductivity ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Hartmann Number ◽  
Magnetic Nanofluid ◽  
Content Type ◽  
Square Enclosure ◽  
Field Dependent

Purpose The purpose of this paper is to investigate the convective heat transfer of magnetic nanofluid (MNF) inside a square enclosure under uniform magnetic fields considering nonlinearity of magnetic field-dependent thermal conductivity. Design/methodology/approach The properties of the MNF (Fe3O4+kerosene) were described by polynomial functions of magnetic field-dependent thermal conductivity. The effect of the transverse magnetic field (0 < H < 105), Hartmann Number (0 < Ha < 60), Rayleigh number (10 <Ra <105) and the solid volume fraction (0 < φ < 4.7%) on the heat transfer performance inside the enclosed space was examined. Continuity, momentum and energy equations were solved using the finite element method. Findings The results show that the Nusselt number increases when the Rayleigh number increases. In contrast, the convective heat transfer rate decreases when the Hartmann number increases due to the strong magnetic field which suppresses the buoyancy force. Also, a significant improvement in the heat transfer rate is observed when the magnetic field is applied and φ = 4.7% (I = 11.90%, I = 16.73%, I = 10.07% and I = 12.70%). Research limitations/implications The present numerical study was carried out for a steady, laminar and two-dimensional flow inside the square enclosure. Also, properties of the MNF are assumed to be constant (except thermal conductivity) under magnetic field. Practical implications The results can be used in thermal storage and cooling of electronic devices such as lithium-ion batteries during charging and discharging processes. Originality/value The accuracy of results and heat transfer enhancement having magnetic field-field-dependent thermal conductivity are noticeable. The results can be used for different applications to improve the heat transfer rate and enhance the efficiency of a system.

Heat Transfer Investigation of a Tube Partially Wrapped by Metal Porous Layer as a Potential Novel Tube for Air Cooled Heat Exchangers

2018 ◽  
Vol 141 (1) ◽  
Author(s):  
M. Mohammadpour-Ghadikolaie ◽  
M. Saffar-Avval ◽  
Z. Mansoori ◽  
N. Alvandifar ◽  
N. Rahmati
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Heat Transfer Rate ◽  
Porous Layer ◽  
Transfer Rate ◽  
Metal Foam ◽  
Convection Heat Transfer ◽  
Darcy Number ◽  
High Heat Transfer

Laminar forced convection heat transfer from a constant temperature tube wrapped fully or partially by a metal porous layer and subjected to a uniform air cross-flow is studied numerically. The main aim of this study is to consider the thermal performance of some innovative arrangements in which only certain parts of the tube are covered by metal foam. The combination of Navier–Stokes and Darcy–Brinkman–Forchheimer equations is applied to evaluate the flow field. Governing equations are solved using the finite volume SIMPLEC algorithm and the effects of key parameters such as Reynolds number, metal foam thermophysical properties, and porous layer thickness on the Nusselt number are investigated. The results show that using a tube which is fully wrapped by an external porous layer with high thermal conductivity, high Darcy number, and low drag coefficient, can provide a high heat transfer rate in the high Reynolds number laminar flow, increasing the Nusselt number almost as high as 16 times compared to a bare tube. The most important result of thisstudy is that by using some novel arrangements in which the tube is partially covered by the foam layer, the heat transfer rate can be increased at least 20% in comparison to the fully wrapped tube, while the weight and material usage can be considerably reduced.

scholarly journals Numerical Analysis of Nanofluids in Differentially Heated Enclosure Undergoing Orthogonal Rotation

2014 ◽  
Vol 2014 ◽  
pp. 1-11 ◽  
Author(s):  
H. Saleh ◽  
I. Hashim
Keyword(s):  
Heat Transfer ◽  
Transfer Rate ◽  
Volume Fraction ◽  
Solid Volume Fraction ◽  
Convection Heat Transfer ◽  
Staggered Grid ◽  
Governing Equations ◽  
Nanoparticles Concentration ◽  
Quantity Of Heat ◽  
Velocity Pressure

Natural convection heat transfer in a rotating, differentially heated enclosure is studied numerically in this paper. The rotating enclosure is filled with water-Ag, water-Cu, water-Al2O3, or water-TiO2nanofluids. The governing equations are in velocity, pressure, and temperature formulation and solved using the staggered grid arrangement together with MAC method. The governing parameters considered are the solid volume fraction,0.0 ≤ ϕ ≤ 0.05, and the rotational speeds,3.5≤ Ω ≤ 17.5 rpm, and the centrifugal force is smaller than the Coriolis force and both forces were kept below the buoyancy force. It is found that the angular locations of the local maximums heat transfer were sensitive to rotational speeds and nanoparticles concentration. The global quantity of heat transfer rate increases about 1.5%, 1.1%, 0.8%, and 0.6% by increasing 1%ϕof the nanoparticles Ag, Cu, Al2O3, and TiO2, respectively, for the considered rotational speeds.

Heat transfer enhancement in microchannels using ribs and secondary flows

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Karthikeyan Paramanandam ◽  
Venkatachalapathy S. ◽  
Balamurugan Srinivasan
Keyword(s):  
Heat Transfer ◽  
Temperature Distribution ◽  
Heat Transfer Enhancement ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Secondary Flows ◽  
Transfer Enhancement ◽  
Heat Transfer Characteristics ◽  
Content Type ◽  
Flow And Heat Transfer

Purpose The purpose of this paper is to study the flow and heat transfer characteristics of microchannel heatsinks with ribs, cavities and secondary channels. The influence of length and width of the ribs on heat transfer enhancement, secondary flows, flow distribution and temperature distribution are examined at different Reynolds numbers. The effectiveness of each heatsink is evaluated using the performance factor. Design/methodology/approach A three-dimensional solid-fluid conjugate heat transfer numerical model is used to study the flow and heat transfer characteristics in microchannels. One symmetrical channel is adopted for the simulation to reduce the computational cost and time. Flow inside the channels is assumed to be single-phase and laminar. The governing equations are solved using finite volume method. Findings The numerical results are analyzed in terms of average Nusselt number ratio, average base temperature, friction factor ratio, pressure variation inside the channel, temperature distribution, velocity distribution inside the channel, mass flow rate distribution inside the secondary channels and performance factor of each microchannels. Results indicate that impact of rib width is higher in enhancing the heat transfer when compared with its length but with a penalty on the pressure drop. The combined effects of secondary channels, ribs and cavities helps to lower the temperature of the microchannel heat sink and enhances the heat transfer rate. Practical implications The fabrication of microchannels are complex, but recent advancements in the additive manufacturing techniques makes the fabrication of the design considered in this numerical study feasible. Originality/value The proposed microchannel heatsink can be used in practical applications to reduce the thermal resistance, and it augments the heat transfer rate when compared with the baseline design.

A comprehensive review on mixed convection for various patterns of kinematically and thermally induced scenarios within cavities

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Leo Lukose ◽  
Tanmay Basak
Keyword(s):  
Heat Transfer ◽  
Mixed Convection ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Inertial Forces ◽  
Content Type ◽  
Flow Interaction ◽  
Experimental Works ◽  
Solid Obstacles ◽  
S Model

Purpose The purpose of this paper is to address various works on mixed convection and proposes 10 unified models (Models 1–10) based on various thermal and kinematic conditions of the boundary walls, thermal conditions and/ or kinematics of objects embedded in the cavities and kinematics of external flow field through the ventilation ports. Experimental works on mixed convection have also been addressed. Design/methodology/approach This review is based on 10 unified models on mixed convection within cavities. Models 1–5 involve mixed convection based on the movement of single or double walls subjected to various temperature boundary conditions. Model 6 elucidates mixed convection due to the movement of single or double walls of cavities containing discrete heaters at the stationary wall(s). Model 7A focuses mixed convection based on the movement of wall(s) for cavities containing stationary solid obstacles (hot or cold or adiabatic) whereas Model 7B elucidates mixed convection based on the rotation of solid cylinders (hot or conductive or adiabatic) within the cavities enclosed by stationary or moving wall(s). Model 8 is based on mixed convection due to the flow of air through ventilation ports of cavities (with or without adiabatic baffles) subjected to hot and adiabatic walls. Models 9 and 10 elucidate mixed convection due to flow of air through ventilation ports of cavities involving discrete heaters and/or solid obstacles (conductive or hot) at various locations within cavities. Findings Mixed convection plays an important role for various processes based on convection pattern and heat transfer rate. An important dimensionless number, Richardson number (Ri) identifies various convection regimes (forced, mixed and natural convection). Generalized models also depict the role of “aiding” and “opposing” flow and combination of both on mixed convection processes. Aiding flow (interaction of buoyancy and inertial forces in the same direction) may result in the augmentation of the heat transfer rate whereas opposing flow (interaction of buoyancy and inertial forces in the opposite directions) may result in decrease of the heat transfer rate. Works involving fluid media, porous media and nanofluids (with magnetohydrodynamics) have been highlighted. Various numerical and experimental works on mixed convection have been elucidated. Flow and thermal maps associated with the heat transfer rate for a few representative cases of unified models [Models 1–10] have been elucidated involving specific dimensionless numbers. Originality/value This review paper will provide guidelines for optimal design/operation involving mixed convection processing applications.

Sign in / Sign up

Export Citation Format

Share Document