Pressure drop and heat transfer characteristics in 60° Chevron plate heat exchanger using Al2O3, GNP and MWCNT nanofluids

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Shiva Singh ◽  
Subrata Kumar Ghosh
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Flow Distribution ◽  
Experimental Results ◽  
Distilled Water ◽  
Heat Transfer Characteristics ◽  
Content Type ◽  
Plate Heat

Purpose The study aims to use nanofluids as coolants for improving heat transfer peculiarities of plate heat exchangers (PHE). The experimental and numerical investigations are thoroughly performed using distilled water-based Al2O3, graphene nanoplatelet (GnP) and multi-walled carbon nanotubes (MWCNT) nanofluids. Design/methodology/approach The numerical simulation based on Single Phase Model (SPM) was performed on a realistic 3 D model of PHE having similar dimensions as of the actual plate. The standard k-epsilon turbulent model was used to solve the problem. The concentration and flow rate of nanofluids were ranging from 0.1 to 1 Vol.% and 1 to 5 lpm, respectively, at 30°C. Whereas, hot side fluid is distilled water at 2 lpm and 80°C. The heat transfer characteristics such as bulk cold outlet temperature, heat transfer rate (HTR), heat transfer coefficient (HTC), Nusselt number (Nu), pressure drop, pumping power, effectiveness and exergy loss were experimentally evaluated using nanofluids in a PHE. Findings The experimental results were then compared with the numerical model. The experimental results revealed maximum enhancement in an average heat transfer rate of 9.86, 14.86 and 17.27% using Al2O3, GnP and MWCNT nanofluids, respectively, at 1 Vol.%. The present computational fluid dynamics model accurately predicts HTR, and the results deviate <1.1% with experiments for all the cases. The temperature and flow distribution show promising results using nanofluids. Originality/value The study helps to visualise heat transfer and flow distribution in PHE using different nanofluids under different operating conditions.

Pressure Drop and Heat Transfer Characteristics of Louvered Fin Heat Exchangers

2013 ◽  
Vol 465-466 ◽  
pp. 500-504 ◽  
Author(s):  
Shahrin Hisham Amirnordin ◽  
Hissein Didane Djamal ◽  
Mohd Norani Mansor ◽  
Amir Khalid ◽  
Md Seri Suzairin ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Heat Transfer Rate ◽  
Heat Exchangers ◽  
Transfer Rate ◽  
Three Dimensional ◽  
Considerable Effect ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics ◽  
Louvered Fin

This paper presents the effect of the changes in fin geometry on pressure drop and heat transfer characteristics of louvered fin heat exchanger numerically. Three dimensional simulation using ANSYS Fluent have been conducted for six different configurations at Reynolds number ranging from 200 to 1000 based on louver pitch. The performance of this system has been evaluated by calculating pressure drop and heat transfer coefficient. The result shows that, the fin pitch and the louver pitch have a very considerable effect on pressure drop as well as heat transfer rate. It is observed that increasing the fin pitch will relatively result in an increase in heat transfer rate but at the same time, the pressure drop will decrease. On the other hand, low pressure drop and low heat transfer rate will be obtained when the louver pitch is increased. Final result shows a good agreement between experimental and numerical results of the louvered fin which is about 12%. This indicates the capability of louvered fin in enhancing the performance of heat exchangers.

Heat transfer enhancement in microchannels using ribs and secondary flows

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Karthikeyan Paramanandam ◽  
Venkatachalapathy S. ◽  
Balamurugan Srinivasan
Keyword(s):  
Heat Transfer ◽  
Temperature Distribution ◽  
Heat Transfer Enhancement ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Secondary Flows ◽  
Transfer Enhancement ◽  
Heat Transfer Characteristics ◽  
Content Type ◽  
Flow And Heat Transfer

Purpose The purpose of this paper is to study the flow and heat transfer characteristics of microchannel heatsinks with ribs, cavities and secondary channels. The influence of length and width of the ribs on heat transfer enhancement, secondary flows, flow distribution and temperature distribution are examined at different Reynolds numbers. The effectiveness of each heatsink is evaluated using the performance factor. Design/methodology/approach A three-dimensional solid-fluid conjugate heat transfer numerical model is used to study the flow and heat transfer characteristics in microchannels. One symmetrical channel is adopted for the simulation to reduce the computational cost and time. Flow inside the channels is assumed to be single-phase and laminar. The governing equations are solved using finite volume method. Findings The numerical results are analyzed in terms of average Nusselt number ratio, average base temperature, friction factor ratio, pressure variation inside the channel, temperature distribution, velocity distribution inside the channel, mass flow rate distribution inside the secondary channels and performance factor of each microchannels. Results indicate that impact of rib width is higher in enhancing the heat transfer when compared with its length but with a penalty on the pressure drop. The combined effects of secondary channels, ribs and cavities helps to lower the temperature of the microchannel heat sink and enhances the heat transfer rate. Practical implications The fabrication of microchannels are complex, but recent advancements in the additive manufacturing techniques makes the fabrication of the design considered in this numerical study feasible. Originality/value The proposed microchannel heatsink can be used in practical applications to reduce the thermal resistance, and it augments the heat transfer rate when compared with the baseline design.

Experimental Research on Heat Transfer Characteristics of Pulsating Heat Pipe

2008 ◽  
Author(s):  
Li Jia ◽  
Yan Li
Keyword(s):  
Heat Transfer ◽  
Heat Pipe ◽  
Heat Transfer Rate ◽  
Experimental Research ◽  
Transfer Rate ◽  
Experimental Results ◽  
Pulsating Heat Pipe ◽  
Heat Transfer Characteristics ◽  
Fill Ratio ◽  
Transfer Characteristics

Experimental research was conducted to understand heat transfer characteristics of pulsating heat pipe in this paper. The PHP is made of high quality glass capillary tube. The heat transfer rate and many other influence factors, the flow patterns were observed in the start-up, transition and stable stage under different fill ratio. The effects of heating position on heat transfer were discussed. The experimental results indicate that no annular flow appeares in top heating condition. The flow pattern in PHP is transferred form bulk flow to semi-annual flow and annual flow, and the performance of heat transfer is improved for down heating case under different fill ratios and heat transfer rate. The experimental results show that the total heat resistant of PHP is increased with fill ratio, and heat transfer rate achieves optimum at filling rate 50%. But for pulsating heat pipe with changing diameters the thermal resistance is higher than that with uniform diameters.

A 3-D Numerical Analysis of the Effect of Fin Pattern on the Thermo-Hydarulic Performance of Plate Heat Exchangers

2013 ◽  
Author(s):  
Kun-Hao Li ◽  
Chi-Chuan Wang
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Heat Exchangers ◽  
Cfd Simulation ◽  
Flow Distribution ◽  
Heat Transfer Characteristics ◽  
Effective Surface ◽  
Plate Heat ◽  
Transfer Characteristics ◽  
Transfer Capability

This study numerically examines some commercially available plate patterns of plate heat exchangers using a 3-D CFD simulation. Detailed flow distribution and heat transfer characteristics subject to three different plate patterns are examined in this study. The plate pattern include GC26 and NT10 (double chevron) and SW26. The effective surface area of the associated plate patterns are 0.8671, 0.6808, and 0.6721 m2, respectively. The corresponding chevron angle are 33°, 64° (double chevron) and 61°, repectively. The calculated results show that the heat transfer efficient for NT10 is higher than that of GC26 by approximately 6.35% and is higher than SW26 by 10.3%. The results indicate that the heat transfer characteristics for the double chevron plate outperform that of the single chevron plate. On the other hand, the pressure drop is also increased with the double chevron as well as chevron angle. However, it is found that the double chevron design provides a better heat transfer capability subject to identical pressure drop.

scholarly journals Experimental Investigation of the Heat Transfer Characteristics of Plate Heat Exchangers Using LiBr/Water as Working Fluid

Energies ◽  
2021 ◽  
Vol 14 (20) ◽  
pp. 6761
Author(s):  
Junhyeok Yong ◽  
Junggyun Ham ◽  
Ohkyung Kwon ◽  
Honghyun Cho
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Plate Heat Exchanger ◽  
Working Fluid ◽  
Heat Transfer Characteristics ◽  
Average Heat ◽  
Plate Heat ◽  
Water Conditions

In this study, the heat exchange characteristics of water–LiBr solutions used as working fluid in a plate heat exchanger (PHE) were experimentally investigated at various concentrations. To analyze the heat transfer characteristics under LiBr/water conditions, a brazing type plate heat exchanger was installed, and the LiBr concentration on the high-temperature side was controlled at 56%, 58%, 60% and 60%. The results showed that the average heat transfer rate under water/water conditions was higher than that under LiBr/water conditions and the average heat transfer rate decreased as the LiBr concentration on the hot side increased. In addition, under both water/water and LiBr/water conditions, the average heat transfer rate and overall heat transfer coefficient increased as the mass flow rate of the working fluid on the hot side increased. When LiBr was used, the Reynolds number (Re) of LiBr on the hot side was more than nine times lower than that of water at the same mass flow rate owing to the influence of the increased viscosity. Based on the data obtained from the water/water and LiBr/water experiments, a correlation for predicting the Nusselt number (Nu) on the hot side in a wide range was developed.

scholarly journals Assessment of TiO2 Nanoconcentration and Twin Impingement Jet of Heat Transfer Enhancement—A Statistical Approach Using Response Surface Methodology

Energies ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 595
Author(s):  
Mahir Faris Abdullah ◽  
Rozli Zulkifli ◽  
Hazim Moria ◽  
Asmaa Soheil Najm ◽  
Zambri Harun ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Tio2 Nanoparticle ◽  
Experimental Results ◽  
Improvement Rate ◽  
Design Expert ◽  
Impingement Jet

Impinging jets are considered to be a well-known technique that offers high local heat transfer rates. No correlation could be established in the literature between the significant parameters and the Nusselt number, and investigation of the interactions between the correlated factors has not been conducted before. An experimental analysis based on the twin impingement jet mechanism was achieved to study the heat transfer rate pertaining to the surface plate. In the current paper, four influential parameters were studied: the spacing between nozzles, velocity, concentration of Nano solution coating and nozzle-plate distance, which are considered to be effective parameters for the thermal conductivity and the heat transfer coefficient of TiO2 nanoparticle, an X-ray diffraction (XRD) and field emission scanning electron microscopy (FESEM) analysis were done, which highlighted the structure and showed that the nanosolution coated the surface homogenously. Moreover, a comparison was done for the experimental results with that of the predicted responses generated by the Design Expert software, Version 7 User’s Guide, USA. A response surface methodology (RSM) was employed to improve a mathematical model by accounting for a D-optimal design. In addition, the analysis of variance (ANOVA) was employed for testing the significance of the models. The maximum Nu of 91.47, where H = S = 1 cm; Reynolds number of 17,000, and TiO2 nanoparticle concentration of 0.5% M. The highest improvement rate in Nusselt was about 26%, achieved with TiO2 Nanoparticle, when S = 3 cm, H = 6 cm and TiO2 nanoparticle = 0.5 M. Furthermore, based on the statistical analysis, the expected values were found to be in satisfactory agreement with that of the empirical data, which was conducted by accounting for the proposed models’ excellent predictability. Multivariate approaches are very useful for researchers, as well as for applications in industrial processes, as they lead to increased efficiency and reduced costs, so the presented results of this work could encourage the overall uses of multivariate methods in these fields. Hypotheses: A comparison was done for the predicted responses generated by the Design Expert software with the experimental results and then studied to verify the following hypotheses: ► Preparation of three concentrations of TiO2 nanosolution was done and studied. ► The heat transfer rate could be increased by surface coating with TiO2 nanoparticle. ► The heat transfer could be improved by the impingement jet technique with suitable adjustments.

Effect of magnetic field-dependent thermal conductivity on natural convection of magnetic nanofluid inside a square enclosure

2019 ◽  
Vol 29 (4) ◽  
pp. 1466-1489 ◽  
Author(s):  
Mohammadhossein Hajiyan ◽  
Shohel Mahmud ◽  
Mohammad Biglarbegian ◽  
Hussein A. Abdullah ◽  
A. Chamkha
Keyword(s):  
Magnetic Field ◽  
Heat Transfer ◽  
Thermal Conductivity ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Hartmann Number ◽  
Magnetic Nanofluid ◽  
Content Type ◽  
Square Enclosure ◽  
Field Dependent

Purpose The purpose of this paper is to investigate the convective heat transfer of magnetic nanofluid (MNF) inside a square enclosure under uniform magnetic fields considering nonlinearity of magnetic field-dependent thermal conductivity. Design/methodology/approach The properties of the MNF (Fe3O4+kerosene) were described by polynomial functions of magnetic field-dependent thermal conductivity. The effect of the transverse magnetic field (0 < H < 105), Hartmann Number (0 < Ha < 60), Rayleigh number (10 <Ra <105) and the solid volume fraction (0 < φ < 4.7%) on the heat transfer performance inside the enclosed space was examined. Continuity, momentum and energy equations were solved using the finite element method. Findings The results show that the Nusselt number increases when the Rayleigh number increases. In contrast, the convective heat transfer rate decreases when the Hartmann number increases due to the strong magnetic field which suppresses the buoyancy force. Also, a significant improvement in the heat transfer rate is observed when the magnetic field is applied and φ = 4.7% (I = 11.90%, I = 16.73%, I = 10.07% and I = 12.70%). Research limitations/implications The present numerical study was carried out for a steady, laminar and two-dimensional flow inside the square enclosure. Also, properties of the MNF are assumed to be constant (except thermal conductivity) under magnetic field. Practical implications The results can be used in thermal storage and cooling of electronic devices such as lithium-ion batteries during charging and discharging processes. Originality/value The accuracy of results and heat transfer enhancement having magnetic field-field-dependent thermal conductivity are noticeable. The results can be used for different applications to improve the heat transfer rate and enhance the efficiency of a system.

A comprehensive review on mixed convection for various patterns of kinematically and thermally induced scenarios within cavities

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Leo Lukose ◽  
Tanmay Basak
Keyword(s):  
Heat Transfer ◽  
Mixed Convection ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Inertial Forces ◽  
Content Type ◽  
Flow Interaction ◽  
Experimental Works ◽  
Solid Obstacles ◽  
S Model

Purpose The purpose of this paper is to address various works on mixed convection and proposes 10 unified models (Models 1–10) based on various thermal and kinematic conditions of the boundary walls, thermal conditions and/ or kinematics of objects embedded in the cavities and kinematics of external flow field through the ventilation ports. Experimental works on mixed convection have also been addressed. Design/methodology/approach This review is based on 10 unified models on mixed convection within cavities. Models 1–5 involve mixed convection based on the movement of single or double walls subjected to various temperature boundary conditions. Model 6 elucidates mixed convection due to the movement of single or double walls of cavities containing discrete heaters at the stationary wall(s). Model 7A focuses mixed convection based on the movement of wall(s) for cavities containing stationary solid obstacles (hot or cold or adiabatic) whereas Model 7B elucidates mixed convection based on the rotation of solid cylinders (hot or conductive or adiabatic) within the cavities enclosed by stationary or moving wall(s). Model 8 is based on mixed convection due to the flow of air through ventilation ports of cavities (with or without adiabatic baffles) subjected to hot and adiabatic walls. Models 9 and 10 elucidate mixed convection due to flow of air through ventilation ports of cavities involving discrete heaters and/or solid obstacles (conductive or hot) at various locations within cavities. Findings Mixed convection plays an important role for various processes based on convection pattern and heat transfer rate. An important dimensionless number, Richardson number (Ri) identifies various convection regimes (forced, mixed and natural convection). Generalized models also depict the role of “aiding” and “opposing” flow and combination of both on mixed convection processes. Aiding flow (interaction of buoyancy and inertial forces in the same direction) may result in the augmentation of the heat transfer rate whereas opposing flow (interaction of buoyancy and inertial forces in the opposite directions) may result in decrease of the heat transfer rate. Works involving fluid media, porous media and nanofluids (with magnetohydrodynamics) have been highlighted. Various numerical and experimental works on mixed convection have been elucidated. Flow and thermal maps associated with the heat transfer rate for a few representative cases of unified models [Models 1–10] have been elucidated involving specific dimensionless numbers. Originality/value This review paper will provide guidelines for optimal design/operation involving mixed convection processing applications.

Numerical Research on Heat Transfer Characteristics Analysis of Two Particles in Supercritical Water

2021 ◽  
Author(s):  
Xiaoyu Li ◽  
Zhenqun Wu ◽  
Huibo Wang ◽  
Hui Jin
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Phase Flow ◽  
Heat Transfer Characteristics ◽  
Particle Cluster ◽  
Two Phase ◽  
Transfer Characteristics

Abstract In the supercritical water (SCW)-particle two-phase flow of fluidized bed, the particles that make up the particle cluster interact with each other through fluid, and it will affect the flow and heat transfer. However, due to the complex properties of SCW, the research on particle cluster is lacking, especially in terms of heat transfer. This research takes two particles as an example to study the heat transfer characteristics between SCW and another particle when one particle exists. This research uses the distance and angle between the two particles as the influencing factors to study the average heat transfer rate and local heat transfer rate. In this research, it is found that the effect is obvious when L/D = 1.1. When L = 1.1D, the temperature field and the flow field will partially overlap. The overlap of the temperature field will weaken the heat transfer between SCW and the particle. The overlap of the flow field has an enhanced effect on the heat transfer between SCW and the particle. The heat transfer between SCW and particles is simultaneously affected by these two effects, especially local heat transfer rate. In addition, this research also found that as the SCW temperature decreases, the thermal conductivity and specific heat of SCW increases, which enhances the heat transfer between SCW and the particles. This research is of great significance for studying the heat transfer characteristics of SCW-particle two-phase flow in fluidized bed.

Sign in / Sign up

Export Citation Format

Share Document