Flexural behavior of fire damaged self-compacting concrete beams strengthened with fiber reinforced polymer (FRP) wrapping

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Mervin Ealiyas Mathews ◽  
Anand N ◽  
Diana Andrushia A ◽  
Tattukolla Kiran ◽  
Khalifa Al-Jabri
Keyword(s):  
Elevated Temperature ◽  
Carbon Fiber ◽  
Ultimate Load ◽  
Research Work ◽  
Fiber Reinforced Polymer ◽  
Flexural Behavior ◽  
Fiber Reinforced ◽  
Self Compacting Concrete ◽  
Content Type ◽  
Reinforced Polymer

PurposeBuilding elements that are damaged by fire are often strengthened by fiber wrapping techniques. Self-compacting concrete (SCC) is an advanced building material that is widely used in construction due to its ability to flow and pass through congested reinforcement and fill the required areas easily without compaction. The aim of the research work is to examine the flexural behavior of SCC subjected to elevated temperature. This research work examines the effect of natural air cooling (AC) and water cooling (WC) on flexural behavior of M20, M30, M40 and M50 grade fire-affected retro-fitted SCC. The results of the investigation will enable the designers to choose the appropriate repair technique for improving the service life of structures.Design/methodology/approachIn this study, an attempt has been made to evaluate the flexural behavior of fire exposed reinforced SCC beams retrofitted with laminates of carbon fiber reinforced polymer (CFRP), basalt fiber reinforced polymer (BFRP) and glass fiber reinforced polymer (GFRP). Beam specimens were cast with M20, M30, M40 and M50 grades of SCC and heated to 925ºC using an electrical furnace for 60 min duration following ISO 834 standard fire curve. The heated SCC beams were cooled by either natural air or water spraying.FindingsThe reduction in the ultimate load carrying capacity of heated beams was about 42% and 55% for M50 grade specimens that were cooled by air and water, respectively, in comparison with the reference specimens. The increase in the ultimate load was 54%, 38% and 27% for the specimens retrofitted with CFRP, BFRP and GFRP, respectively, compared with the fire-affected specimens cooled by natural air. Water-cooled specimens had shown higher level of damage than the air-cooled specimens. The specimens wrapped with carbon fiber could able to improve the flexural strength than basalt and glass fiber wrapping.Originality/valueSCC, being a high performance concrete, is essential to evaluate the performance under fire conditions. This research work provides the flexural behavior and physical characteristics of SCC subjected to elevated temperature as per ISO rate of heating. In addition attempt has been made to enhance the flexural strength of fire-exposed SCC with wrapping using different fibers. The experimental data will enable the engineers to choose the appropriate material for retrofitting.

Experimental study on the bond behavior of the CFRP-steel interface under the freeze–thaw cycles

2019 ◽  
Vol 54 (1) ◽  
pp. 13-29 ◽  
Author(s):  
Yu-Yang Pang ◽  
Gang Wu ◽  
Hai-Tao Wang ◽  
Zhi-Long Su ◽  
Xiao-Yuan He
Keyword(s):  
Carbon Fiber ◽  
Bond Length ◽  
Ultimate Load ◽  
Fiber Reinforced Polymer ◽  
Carbon Fiber Reinforced Polymer ◽  
Fiber Reinforced ◽  
Bond Slip ◽  
Freeze Thaw ◽  
Reinforced Polymer ◽  
Carbon Fiber Reinforced

The bond–slip degradation relationship between carbon fiber-reinforced polymer and steel in a freeze–thaw environment is crucial to evaluate the long-term service performance of steel structures strengthened with carbon fiber-reinforced polymer plates. However, limited studies on the durability and long-term performance of the carbon fiber-reinforced polymer-steel-bonded interface are the major obstacle for the application of carbon fiber-reinforced polymer plates in strengthening steel structures. This paper reports an experimental study to investigate the effects of the carbon fiber-reinforced polymer bond length and the freeze–thaw cycles on the bond behavior of the carbon fiber-reinforced polymer-steel-bonded interface. The three-dimensional digital image correlation technique is applied to obtain displacements and strains on the surface of the single-shear specimen. The experimental results present herein include the failure mode, the ultimate load, the carbon fiber-reinforced polymer strain distribution, the displacement distribution, and the bond–slip relationship. The results show that the ultimate load increases with increasing bond length until a certain bond length value is reached, after which the ultimate load remained approximately constant, and the ultimate loads of carbon fiber-reinforced polymer-steel interface decrease gradually under freeze–thaw cycles. The bond–slip parameters degradation models are proposed, and the bond–slip degradation relationship under the freeze–thaw cycles is established. Finally, the bond–slip degradation relationship is confirmed through comparisons with the experimental results.

Challenges in abrasive jet machining of fiber-reinforced polymeric composites – a review

2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
S. Madhu ◽  
M. Balasubramanian
Keyword(s):  
Surface Roughness ◽  
Carbon Fiber ◽  
Glass Fiber ◽  
Polymeric Composites ◽  
Fiber Reinforced Polymer ◽  
Fiber Reinforced ◽  
Content Type ◽  
Abrasive Jet Machining ◽  
Reinforced Polymer ◽  
Wide Acceptance

Purpose The purpose of this study is for solving many issues in production that includes processing of complex-shaped profile, machining of high-strength materials, good surface finish with high-level precision and minimization of waste. Among the various advanced machining processes, abrasive jet machining (AJM) is one of the non-traditional machining techniques used for various applications such as polishing, deburring and hole making. Hence, an overview of the investigations done on carbon fiber-reinforced polymer (CFRP) and glass fiber-reinforced polymer (GRFP) composites becomes important. Design/methodology/approach Discussion on various approaches to AJM, the effect of process parameters on the glass fiber and carbon fiber polymeric composites are presented. Kerf characteristics, surface roughness and various nozzle design were also discussed. Findings It was observed that abrasive jet pressure, stand-off distance, traverse rate, abrasive size, nozzle diameter, angle of attack are the significant process parameters which affect the machining time, material removal rate, top kerf, bottom kerf and kerf angle. When the particle size is maximum, the increased kinetic energy of the particle improves the penetration depth on the CFRP surface. As the abrasive jet pressure is increased, the cutting process is enabled without severe jet deflection which in turn minimizes the waviness pattern, resulting in a decrease of the surface roughness. Research limitations/implications The review is limited to glass fiber and carbon fiber polymeric composites. Practical implications In many applications, the use of composite has gained wide acceptance. Hence, machining of the composite need for the study also has gained wide acceptance. Social implications The usage of composites reduces the usage of very costly materials of high density. The cost of the material also comes down. Originality/value This paper is a comprehensive review of machining composite with abrasive jet. The paper covers in detail about machining of only GFRP and CFRP composites with various nozzle designs, unlike many studies which has focused widely on general AJM of various materials.

scholarly journals Experimental Analysis of Continuous Beams Made of Self-Compacting Concrete (Scc) Strengthened with Fiber Reinforced Polymer (Frp) Materials

2021 ◽  
Vol 11 (9) ◽  
pp. 4032
Author(s):  
Žarko Petrović ◽  
Bojan Milošević ◽  
Slobodan Ranković ◽  
Biljana Mladenović ◽  
Dragan Zlatkov ◽  
...  
Keyword(s):  
Experimental Analysis ◽  
Failure Modes ◽  
Fiber Reinforced Polymer ◽  
Flexural Behavior ◽  
Engineering Practice ◽  
Fiber Reinforced ◽  
Self Compacting Concrete ◽  
Near Surface ◽  
Reinforced Polymer ◽  
Continuous Beams

Strengthening of concrete structures is applied as a solution for various deterioration problems in civil engineering practice. This also refers to the structures made of self-compacting concrete (SCC), which is increasingly in use, but there is a lack of research in this field. This paper presents an experimental analysis of flexural behavior of reinforced concrete (RC) continuous beams made of SCC, strengthened with fiber reinforced polymer (FRP) materials (glass (GFRP) and carbon (CFRP) bars, CFRP laminates), by the use of near surface mounted (NSM) and externally bonded (EB) methods. Six two-span continuous beams of a total length of 3200 mm, with the span between supports of 1500 mm and 120/200 mm cross section, were subjected to short-term load and tested. The displacements of beams and the strains in concrete, steel reinforcement, FRP bars and tapes were recorded until failure under a monotonically increasing load. The ultimate load capacities of the strengthened beams were enhanced by 22% to 82% compared to the unstrengthened control beam. The ductility of beams strengthened with GFRP bars was satisfactory, while the ductility of beams strengthened with CFRP bars and tapes was very small, so the failure modes of these beams were brittle.

Exploratory experimental study on flexural behavior of CFRP-reinforced concrete beams subjected to acidic loading effect

2018 ◽  
Vol 21 (14) ◽  
pp. 2184-2197 ◽  
Author(s):  
Hai-Yang Luan ◽  
Ying-Fang Fan ◽  
An Chen ◽  
Shi-Yi Zhang
Keyword(s):  
Reinforced Concrete ◽  
Carbon Fiber ◽  
Concrete Beams ◽  
Reinforced Concrete Beams ◽  
Fiber Reinforced Polymer ◽  
Flexural Behavior ◽  
Carbon Fiber Reinforced Polymer ◽  
Fiber Reinforced ◽  
Reinforced Polymer ◽  
Carbon Fiber Reinforced

This article presents an exploratory study on the flexural behavior of carbon fiber–reinforced polymer–reinforced concrete beams subjected to acidic loading effect. To this end, an artificial acid rain with a pH level of 1.5 was prepared by mixing sulfate and nitric acid solutions. Eight reinforced concrete beams with/without carbon fiber–reinforced polymer applications were constructed and conditioned using the artificial acid rain. During conditioning, bending loads were applied to the top surfaces of the beams to simulate the acidic loading action. Three carbon fiber–reinforced polymer reinforcement schemes (corrosion reinforcement, reinforcement corrosion, and cracking reinforcement) were considered. After conditioning, the length and quantity of initial cracks in the beams were recorded. A combined ultrasonic–rebound method was then adopted to measure the strength and corrosion depth of the concrete and evaluate the beams’ integrity. Next, four-point bending tests were conducted to study the beams’ flexural behavior. It can be concluded that all beams deteriorated with the increase of the corrosion time. Carbon fiber–reinforced polymer–reinforced concrete beams performed better than normal reinforced concrete beams under the acidic loading effect. The initial cracks can influence the flexural behavior of carbon fiber–reinforced polymer–reinforced concrete beams.

Sign in / Sign up

Export Citation Format

Share Document