Fabrication of bimetallic additively manufactured structure (BAMS) of low carbon steel and 316L austenitic stainless steel with wire + arc additive manufacturing

2019 ◽  
Vol 26 (3) ◽  
pp. 519-530 ◽  
Author(s):  
Md. Rumman Ul Ahsan ◽  
Ali Newaz Mohammad Tanvir ◽  
Taylor Ross ◽  
Ahmed Elsawy ◽  
Min-Suk Oh ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Additive Manufacturing ◽  
Carbon Steel ◽  
Low Carbon Steel ◽  
Hardness Profile ◽  
Sudden Increase ◽  
Low Carbon ◽  
Content Type ◽  
Multiple Materials ◽  
Wire Arc Additive Manufacturing

Purpose Wire + arc additive manufacturing (WAAM) uses existing welding technology to make a part from metal deposited in an almost net shape. WAAM is flexible in that it can use multiple materials successively or simultaneously during the manufacturing of a single component. Design/methodology/approach In this work, a gas metal arc welding (GMAW) based wire + arc additive manufacturing (WAAM) system has been developed to use two material successively and fabricate bimetallic additively manufactured structure (BAMS) of low carbon steel and AISI 316L stainless steel (SS). Findings The interface shows two distinctive zones of LCS and SS deposits without any weld defects. The hardness profile shows a sudden increase of hardness at the interface, which is attributed to the migration of chromium from the SS. The tensile test results show that the bimetallic specimens failed at the LCS side, as LCS has lower strength of the materials used. Originality/value The microstructural features and mechanical properties are studied in-depth with special emphasis on the bimetallic interface.

Development of near homogeneous properties in wire arc additive manufacturing process for near-net shaped structural component of low-carbon steel

2021 ◽  
pp. 095440622110454
Author(s):  
Amrit Raj Paul ◽  
Manidipto Mukherjee ◽  
Manivannan Raja ◽  
Soumyajit Kundu ◽  
Avik Chatterjee
Keyword(s):  
Additive Manufacturing ◽  
Time Delay ◽  
Carbon Steel ◽  
Structural Component ◽  
Low Carbon Steel ◽  
Tensile Behaviour ◽  
Void Coalescence ◽  
Hardness Profile ◽  
Low Carbon ◽  
Wire Arc Additive Manufacturing

Low-carbon steel is a common structural material, but additively manufactured structural component of this material is rare due to its inhomogeneous properties. In this article, the wire arc additive manufacturing method was used to achieve near homogeneous properties of a low-carbon steel structural component. The process heat input was optimised for the desired layer geometry, and then the optimal energy was applied with a time delay to deposit individual layers. The time delay was used to achieve cyclic heating and cooling treatment of deposited layers. The best possible robotic tool path movement with multi point arcing was further adopted in the study to achieve proper thermal distribution across the structural component. The microstructure of layers was dominated by quasi-polygonal ferrite morphology and pearlite precipitation, with little variation in quantity across the component. The hardness profile was almost consistent with the average hardness of ∼176.92 HV. The proof stress slightly increases with decrease in grain size and increase in ferrite/pearlite ratio, however, the overall tensile behaviour is homogeneous with average σ0.2, σu and ε% values of 427.78 MPa, 527.89 MPa and 22.31%, respectively. The quasi-ductile fracture was generally occurred due to void coalescence around larger inclusions. The overall analysis showed that more than 90% of homogeneity was achieved in microstructural and mechanical behaviour of the deposited component.

scholarly journals Environmental Behavior of Low Carbon Steel Produced by a Wire Arc Additive Manufacturing Process

Metals ◽  
2019 ◽  
Vol 9 (8) ◽  
pp. 888 ◽  
Author(s):  
Ron ◽  
Levy ◽  
Dolev ◽  
Leon ◽  
Shirizly ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Additive Manufacturing ◽  
Carbon Steel ◽  
Stress Corrosion ◽  
Environmental Behavior ◽  
Low Carbon Steel ◽  
General Corrosion ◽  
Low Carbon ◽  
Corrosion Performance ◽  
Wire Arc Additive Manufacturing

: Current additive manufacturing (AM) processes are mainly focused on powder bed technologies, such as electron beam melting (EBM) and selective laser melting (SLM). However, the main disadvantages of such techniques are related to the high cost of metal powder, the degree of energy consumption, and the sizes of the components, that are limited by the size of the printing cell. The aim of the present study was to evaluate the environmental behavior of low carbon steel (ER70S-6) produced by a relatively inexpensive AM process using wire feed arc welding. The mechanical properties were examined by tension testing and hardness measurements, while microstructure was assessed by scanning electron microscopy and X-ray diffraction analysis. General corrosion performance was evaluated by salt spray testing, immersion testing, potentiodynamic polarization analysis, and electrochemical impedance spectroscopy. Stress corrosion performance was characterized in terms of slow strain rate testing (SSRT). All corrosion tests were carried out in 3.5% NaCl solution at room temperature. The results indicated that the general corrosion resistance of wire arc additive manufacturing (WAAM) samples were quite similar to those of the counterpart ST-37 steel and the stress corrosion resistance of both alloys was adequate. Altogether, it was clearly evident that the WAAM process did not encounter any deterioration in corrosion performance compared to its conventional wrought alloy counterpart.

scholarly journals EFFECTS OF WELDING CURRENT ON THE SHAPE AND MICROSTRUCTURE FORMATION OF THIN-WALLED LOW-CARBON PARTS BUILT BY WIRE ARC ADDITIVE MANUFACTURING

2020 ◽  
Vol 58 (4) ◽  
pp. 461
Author(s):  
Van Thao Le ◽  
Quang Huy Hoang ◽  
Van Chau Tran ◽  
Dinh Si Mai ◽  
Duc Manh Dinh ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Carbon Steel ◽  
Low Carbon Steel ◽  
Welding Current ◽  
Welding Parameters ◽  
Low Carbon ◽  
Microstructure Formation ◽  
Thin Walled ◽  
Wire Arc Additive Manufacturing

Wire arc additive manufacturing (WAAM) is nowadays gaining much attention from both the academic and industrial sectors for the manufacture of medium and large dimension metal parts because of its high deposition rate and low costs of equipment investment. In the literature, WAAM has been extensively investigated in terms of the shape and dimension accuracy of built parts. However, limited research has focused on the effects of welding parameters on the microstructural characteristics of parts manufactured by this process. In this paper, the effects of welding current in the WAAM process on the shape and the microstructure formation of built thin-walled low-carbon steel components were studied. For this purpose, the thin-walled low-carbon steel samples were built layer-by-layer on the substrates by using an industrial gas metal arc welding robot with different levels of welding current. The shape, microstructures and mechanical properties of built samples were then analyzed. The obtained results show that the welding current plays an important role in the shape stability, but does not significantly influence on the microstructure formation of built thin-walled samples. The increase of the welding current only leads to coarser grain size and resulting in decreasing the hardness of built materials in each zone of the built sample. The mechanical properties (hardness and tensile properties) of the WAAM-built thin-walled low-carbon steel parts are also comparable to those of wrought low-carbon steel, and to be adequate with real applications.

Wire arc additive manufacturing of thin-wall low-carbon steel parts: Microstructure and mechanical properties

2020 ◽  
Vol 34 (22n24) ◽  
pp. 2040154
Author(s):  
Van Thao Le ◽  
Tien Long Banh ◽  
Duc Toan Nguyen ◽  
Van Tao Le
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Carbon Steel ◽  
Heat Input ◽  
Low Carbon Steel ◽  
Production Costs ◽  
High Deposition Rate ◽  
Thin Wall ◽  
Low Carbon ◽  
Wire Arc Additive Manufacturing

Wire arc additive manufacturing (WAAM) has received much attention for manufacturing metal parts with medium and large dimensions because of its high deposition rate and low production costs. In this study, the effects of the heat input on the microstructure formation of thin-wall low-carbon steel parts built by a WAAM process were addressed. The mechanical properties of built materials were also studied. The results indicate that the heat input significantly influences on the shape of built thin walls, but has slight effects on the microstructure evolution of built materials. The WAAM thin-wall low-carbon steel presents suitable microstructures and good tensile strengths (YS: 320 – 362 MPa, UTS: 429 – 479 MPa) that are adequate with industrial applications.

scholarly journals Structure of a 3D frame-bridge NiTi sample deposited on a low carbon steel substrate by wire arc additive manufacturing

2020 ◽  
Vol 10 (4) ◽  
pp. 496-500
Author(s):  
Natalia Resnina ◽  
I.A. Palani ◽  
Pavel Liulchak ◽  
Sergey Belyaev ◽  
S.S. Mani Prabu ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Carbon Steel ◽  
Steel Substrate ◽  
Low Carbon Steel ◽  
Low Carbon ◽  
Wire Arc Additive Manufacturing

Investigation of mechanical properties and parametric optimization of the dissimilar GTAW of AISI 304 stainless steel and low carbon steel

2018 ◽  
Vol 15 (5) ◽  
pp. 584-591 ◽  
Author(s):  
Tunde Isaac Ogedengbe ◽  
Taiwo Ebenezer Abioye ◽  
Augusta Ijeoma Ekpemogu
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Carbon Steel ◽  
Low Carbon Steel ◽  
304 Stainless Steel ◽  
Low Carbon ◽  
Aisi 304 Stainless Steel ◽  
Aisi 304 ◽  
Content Type ◽  
Weld Region

Purpose The purpose of this study is to conduct gas tungsten arc dissimilar welding of AISI 304 stainless steel and low carbon steel within a process window so as to investigate the effects of current, speed and gas flow rate (GFR) on the microstructure and mechanical properties of the weldments. Design/methodology/approach The welding experiment was carried out at different combinations of parameters using WN-250S Kaierda electric welding machine. A combination of scanning electron microscopy and energy dispersive X-ray spectroscopy was used to examine the microstructure of the weldments. Micro-hardness and tensile tests were performed using Vickers hardness tester and Instron universal testing machine, respectively. ANOVA was used to analyze the significance of the parameters on the mechanical properties. Findings The microstructure of the weld region is characterized with dendritic structure with the existence of ferrite and austenite phases. The utilized parameters show significant effects on the ultimate tensile strength (UTS) of the weldments. The current and GFR were found to be the most and least significant factors, respectively. Both the grain size and weld penetration contributed to the UTS of the weldments. The UTS (427-886 MPa) increased with decreasing current and welding speed. In all samples, the weld region exhibited higher hardness (297-396 HV) than the HAZ in the base metals (maximum of 223 Â ± 6 HV). All the three factors show significant effect with the welding speed contributing mostly to the hardness of the weld region. Originality/value The parametric combination that gives the optimum mechanical performance of the dissimilar gas tungsten arc weldments of AISI 304 stainless steel and low carbon steel was established.

Estimation of Some Mechanical Properties for Similar & Dissimilar Welded Joints

2014 ◽  
Vol 2 (1) ◽  
pp. 59-76
Author(s):  
Abdullah Daie'e Assi
Keyword(s):  
Stainless Steel ◽  
Carbon Steel ◽  
Austenitic Stainless Steel ◽  
Base Metal ◽  
Welded Joints ◽  
Plate Thickness ◽  
Low Carbon Steel ◽  
Dissimilar Metals ◽  
Low Carbon ◽  
Steel Type

This research deals with the choice of the suitable filler metal to weld the similar and dissimilar metals (Low carbon steel type A516 & Austenitic stainless steel type 316L) under constant conditions such as, plate thickness (6 mm), voltage (78 v), current (120 A), straight polarity. This research deals with three major parts. The first parts Four types of electrodes were used for welding of dissimilar metals (C.St A516 And St.St 316L) two from mild steel (E7018, E6013) and other two from austenitic stainless steel (E309L, E308L) various inspection were carried out include (Visual T., X-ray T., δ- Ferrite phase T., and Microstructures T.) and mechanical testing include (tensile T., bending T. and micro hardness T.) The second parts done by used the same parameters to welding similar metals from (C.St A516) Or (St.St 316L). The third parts deals with welding of dissimilar weldments (C.St And St.St) by two processes, gas tungsten are welding (GTAW) and shielded metal are welding (SMAW).        The results indicated that the spread of carbon from low carbon steel to the welding zone in the case of welding stainless steel elect pole (E309L) led to Configuration Carbides and then high hardness the link to high values ​​compared with the base metal. In most similar weldments showed hardness of the welding area is  higher than the hardness of the base metal. The electrode (E309L) is the most suitable to welding dissimilar metals from (C.St A516 With St.St 316L). The results also showed that the method of welding (GTAW) were better than the method of welding (SMAW) in dissimilar welded joints (St.St 316L with C.St A516) in terms of irregular shape and integrity of the welding defects, as well as characterized this weldments the high-lift and resistance ductility good when using the welding conditions are similar.

Sign in / Sign up

Export Citation Format

Share Document