A fully-integrated 130nm CMOS DC-DC step-down converter, regulated by a constant on/off-time control system

2008 ◽  
Author(s):  
Mike Wens ◽  
Michiel Steyaert
Keyword(s):  
Control System ◽  
Fully Integrated ◽  
Time Control ◽  
Step Down ◽  
Off Time

scholarly journals Traffic Light Priority for Trams in Warsaw as a Tool for Transport Policy and Reduction of Energy Consumption

2021 ◽  
Vol 13 (8) ◽  
pp. 4180
Author(s):  
Andrzej Czerepicki ◽  
Tomasz Krukowicz ◽  
Anna Górka ◽  
Jarosław Szustek
Keyword(s):  
Control System ◽  
Energy Consumption ◽  
Electric Energy ◽  
Fixed Time ◽  
Pollutant Emissions ◽  
Computer Simulation Model ◽  
Traffic Light ◽  
Electric Energy Consumption ◽  
Time Control ◽  
Reduction Of Energy Consumption

The article presents an analysis of priority solutions for trams at a selected sequence of intersections in Warsaw (Poland). An analysis of the literature has shown the topicality of this issue. A computer simulation model of a coordinated sequence of intersections was constructed. Three test scenarios were designed: the existing control system, the new coordinated fixed-time control system, and the adaptive control system with active priority. In the simulation process, detailed travel characteristics of trams and other traffic participants in a selected section were obtained for the three varying scenarios. Electric energy consumption for traction needs and pollutant emissions was then estimated for each of the variants. It was concluded that for the analyzed configuration, implementation of the adaptive priority will result in a reduction of tram time losses by up to 25%, a reduction in energy consumption by up to 23%, and a reduction in the emission of pollutants from individual vehicles by up to 3% in relation to the original variant. The conducted research may be the basis for a comprehensive method of assessing the effectiveness of applying the adaptative priority when designing new tramway lines and modernizing the existing ones.

A New Flexible Rapid Thermal Processing System

1995 ◽  
Vol 389 ◽  
Author(s):  
K. C. Saraswat ◽  
Y. Chen ◽  
L. Degertekin ◽  
B. T. Khuri-Yakub
Keyword(s):  
Control System ◽  
Real Time ◽  
Processing System ◽  
Process Conditions ◽  
Temperature Uniformity ◽  
Real Time Control ◽  
Wafer Temperature ◽  
Time Control ◽  
Wide Range ◽  
Optical Flux

ABSTRACTA highly flexible Rapid Thermal Multiprocessing (RTM) reactor is described. This flexibility is the result of several new innovations: a lamp system, an acoustic thermometer and a real-time control system. The new lamp has been optimally designed through the use of a “virtual reactor” methodology to obtain the best possible wafer temperature uniformity. It consists of multiple concentric rings composed of light bulbs with horizontal filaments. Each ring is independently and dynamically controlled providing better control over the spatial and temporal optical flux profile resulting in excellent temperature uniformity over a wide range of process conditions. An acoustic thermometer non-invasively allows complete wafer temperature tomography under all process conditions - a critically important measurement never obtained before. For real-time equipment and process control a model based multivariable control system has been developed. Extensive integration of computers and related technology for specification, communication, execution, monitoring, control, and diagnosis demonstrates the programmability of the RTM.

Servo Control System of Electrical Discharge Machining Based on PMAC

2014 ◽  
Vol 926-930 ◽  
pp. 1497-1500
Author(s):  
Xu Yang Chu ◽  
Gang Liu ◽  
Chun Mei Wang ◽  
Kai Zhu ◽  
Da Yun Chen ◽  
...  
Keyword(s):  
Control System ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Control Function ◽  
Servo Control ◽  
Human Computer Interface ◽  
Real Time Control ◽  
Time Control ◽  
Servo Control System ◽  
Hardware Resource

This paper describe the principles of Servo Control System of Electrical Discharge Machining Based on PMAC .To meet the requirements of processing and Put forward based on PMAC servo control system. This control system combines hardware resource with PMAC real-time control function. Elaborate human-computer interface developing process.

Simultaneous Removal of Nitrogen and Phosphorus in Intermittently Aerated 2-Tank Activated Sludge Process Using DO and ORP-Bending-Point Control

1993 ◽  
Vol 28 (11-12) ◽  
pp. 513-521 ◽  
Author(s):  
Kousei Sasaki ◽  
Yasuji Yamamoto ◽  
Kazushi Tsumura ◽  
Shigeru Hatsumata ◽  
Masahiro Tatewaki
Keyword(s):  
Control System ◽  
Activated Sludge ◽  
Phosphorus Uptake ◽  
Material Balance ◽  
Phosphorus Release ◽  
Test Plant ◽  
Activated Sludge Process ◽  
Time Sharing ◽  
Nitrogen And Phosphorus ◽  
Time Control

The 2-tank intermittent aeration method is an anaerobic-aerobic activated sludge process of time-sharing type in which 2 complete mixing reaction tanks are connected in series, and aeration and agitation are periodically repeated in each tank. We have developed a new control system for the process which can secure anaerobic, anoxic and aerobic conditions through a combination of DO and ORP-Bending-point (corresponding to termination of denitrification) emergence time control. In the 1st tank, nitrification and phosphorus uptake occur in the aeration period, followed by denitrification and phosphorus release in the agitation. The 2nd tank performs nitrification and phosphorus uptake in the aeration and denitrification in the agitation. One cycle of aeration and agitation is approximately 2 hours. This control system was applied to the test plant (influent flow rate: 225 I/day) for two months under the conditions of HRT 16 hours and temperature 20 ±2 °C. We achieved stable and high removal ratios: TOC 94.9 %, T-N 89.4 %, and T-P 95.5 %. We also investigated the mechanisms of nitrogen and phosphorus removal and their material balance.

Sign in / Sign up

Export Citation Format

Share Document