Influence of the surface roughness on images acquired by flying spot active thermography: Case of the high pressure turbine blades

2012 ◽  
Author(s):  
T. Maffren ◽  
F. Lepoutre ◽  
G. Deban ◽  
A. Mavel ◽  
P. Juncar
Keyword(s):  
Surface Roughness ◽  
High Pressure ◽  
Turbine Blades ◽  
High Pressure Turbine ◽  
Active Thermography ◽  
Flying Spot

Aerothermal Effect of Cavity Welding Beads on a Transonic Squealer Tip

2020 ◽  
Author(s):  
Joao Vieira ◽  
John Coull ◽  
Peter Ireland ◽  
Eduardo Romero
Keyword(s):  
High Pressure ◽  
Film Cooling ◽  
Turbine Blades ◽  
Reynolds Numbers ◽  
High Pressure Turbine ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Aerodynamic Loss ◽  
Blade Tip ◽  
Mass Flow Rates

Abstract High pressure turbine blade tips are critical for gas turbine performance and are sensitive to small geometric variations. For this reason, it is increasingly important for experiments and simulations to consider real geometry features. One commonly absent detail is the presence of welding beads on the cavity of the blade tip, which are an inherent by-product of the blade manufacturing process. This paper therefore investigates how such welds affect the Nusselt number, film cooling effectiveness and aerodynamic performance. Measurements are performed on a linear cascade of high pressure turbine blades at engine realistic Mach and Reynolds numbers. Two cooled blade tip geometries were tested: a baseline squealer geometry without welding beads, and a case with representative welding beads added to the tip cavity. Combinations of two tip gaps and several coolant mass flow rates were analysed. Pressure sensitive paint was used to measure the adiabatic film cooling effectiveness on the tip, which is supplemented by heat transfer coefficient measurements obtained via infrared thermography. Drawing from all of this data, it is shown that the weld beads have a generally detrimental impact on thermal performance, but with local variations. Aerodynamic loss measured downstream of the cascade is shown to be largely insensitive to the weld beads.

scholarly journals Evaluation of High Pressure Turbine Blade Coatings on an LM2500 Rainbow Rotor

1995 ◽  
Author(s):  
B. Nagaraj ◽  
G. Katz ◽  
A. F. Maricocchi ◽  
M. Rosenzweig
Keyword(s):  
High Pressure ◽  
Turbine Blades ◽  
Leading Edge ◽  
Service Evaluation ◽  
High Pressure Turbine ◽  
Barrier Coating ◽  
Marine Propulsion ◽  
Corrosion Resistant Coatings ◽  
Stage 1 ◽  
Plasma Sprayed

Two LM2500 rainbow rotors with repaired stage 1 and stage 2 high pressure turbine blades are being assembled for marine propulsion service evaluation by the US Navy. The blades have seen between 5,000 and 15,000 hours of service in the Navy’s Fleets. A number of corrosion resistant coatings including plasma sprayed CoCrAlHf (bill of material), composite plated CoCrAlHf, platinum aluminide, aluminum silicide, and physical vapor deposited yttria stabilized zirconia thermal barrier coating (PVD TBC) will be evaluated in the rainbow rotor. This paper will discuss the advantages and microstructures of the various coatings. Composite plated CoCrAlHf, and PVD TBCs were recently service evaluated in an industrial LM2500 rainbow rotor for 10,500 hours. Both these coatings performed well, although the PVD TBC had local spallation at the leading edge. This paper will review the details of performance of these two coatings in the industrial LM2500 application.

Using CFD to Reduce Resonant Stresses on a Single-Stage, High-Pressure Turbine Blade

2002 ◽  
Author(s):  
J. P. Clark ◽  
A. S. Aggarwala ◽  
M. A. Velonis ◽  
R. E. Gacek ◽  
S. S. Magge ◽  
...  
Keyword(s):  
High Pressure ◽  
Turbine Blade ◽  
Guide Vane ◽  
Turbine Blades ◽  
Suction Side ◽  
Lessons Learned ◽  
Single Stage ◽  
Navier Stokes ◽  
High Pressure Turbine ◽  
Time Resolved

The ability to predict levels of unsteady forcing on high-pressure turbine blades is critical to avoid high-cycle fatigue failures. In this study, 3D time-resolved computational fluid dynamics is used within the design cycle to predict accurately the levels of unsteady forcing on a single-stage high-pressure turbine blade. Further, nozzle-guide-vane geometry changes including asymmetric circumferential spacing and suction-side modification are considered and rigorously analyzed to reduce levels of unsteady blade forcing. The latter is ultimately implemented in a development engine, and it is shown successfully to reduce resonant stresses on the blade. This investigation builds upon data that was recently obtained in a full-scale, transonic turbine rig to validate a Reynolds-Averaged Navier-Stokes (RANS) flow solver for the prediction of both the magnitude and phase of unsteady forcing in a single-stage HPT and the lessons learned in that study.

Numerical Prediction of Cooling Performance Sensitivity of 1st Stage Nozzle Guide Vane Under Aerothermal Conditions

2019 ◽  
Author(s):  
Prasert Prapamonthon ◽  
Bo Yin ◽  
Guowei Yang ◽  
Mohan Zhang
Keyword(s):  
Heat Transfer ◽  
Surface Roughness ◽  
High Pressure ◽  
Guide Vane ◽  
Pressure Ratio ◽  
Inlet Temperature ◽  
High Pressure Turbine ◽  
Cooling Performance ◽  
Nozzle Guide Vane ◽  
Nozzle Guide

Abstract To obtain high power and thermal efficiency, the 1st stage nozzle guide vanes of a high-pressure turbine need to operate under serious circumstances from burned gas coming out of combustors. This leads to vane suffering from effects of high thermal load, high pressure and turbulence, including flow-separated transition. Therefore, it is necessary to improve vane cooling performance under complex flow and heat transfer phenomena caused by the integration of these effects. In fact, these effects on a high-pressure turbine vane are controlled by several factors such as turbine inlet temperature, pressure ratio, turbulence intensity and length scale, vane curvature and surface roughness. Furthermore, if the vane is cooled by film cooling, hole configuration and blowing ratio are important factors too. These factors can change the aerothermal conditions of the vane operation. The present work aims to numerically predict sensitivity of cooling performances of the 1st stage nozzle guide vane under aerodynamic and thermal variations caused by three parameters i.e. pressure ratio, coolant inlet temperature and height of vane surface roughness using Computational Fluid Dynamics (CFD) with Conjugate Heat Transfer (CHT) approach. Numerical results show that the coolant inlet temperature and the vane surface roughness parameters have significant effects on the vane temperature, thereby affecting the vane cooling performances significantly and sensitively.

Sign in / Sign up

Export Citation Format

Share Document