The influence of energy separated nozzle on the gas flow parameters for SF6 circuit breaker

2017 ◽  
Author(s):  
Li-Ying Li ◽  
Jia-Xiu Sun ◽  
Jun Wang
Keyword(s):  
Gas Flow ◽  
Circuit Breaker ◽  
Flow Parameters

Modeling of pressure losses on friction in three-layer laminar flows

2003 ◽  
Vol 3 ◽  
pp. 208-219
Author(s):  
A.M. Ilyasov
Keyword(s):  
Pressure Loss ◽  
Gas Flow ◽  
Mutual Influence ◽  
Fluid Model ◽  
Immiscible Liquid ◽  
Laminar Flows ◽  
Pressure Losses ◽  
Flow Parameters ◽  
Interphase Boundaries ◽  
Closing Relations

In this paper we propose a model for determining the pressure loss due to friction in each phase in a three-layer laminar steady flow of immiscible liquid and gas flow in a flat channel. This model generalizes an analogous problem for a two-layer laminar flow, proposed earlier. The relations obtained in the final form for the pressure loss due to friction in liquids can be used as closing relations for the three-fluid model. These equations take into account the influence of interphase boundaries and are an alternative to the approach used in foreign literature. In this approach, the wall and interphase voltages are approximated by the formulas for a single-phase flow and do not take into account the mutual influence of liquids on the loss of pressure on friction in phases. The distribution of flow parameters in these two models is compared.

scholarly journals Experimental Research of Gaseous Emissions Impact on the Performance of New-Design Cylindrical Multi-Channel Cyclone with Adjustable Half-Rings

2022 ◽  
Vol 14 (2) ◽  
pp. 902
Author(s):  
Aleksandras Chlebnikovas ◽  
Dainius Paliulis ◽  
Kristina Kilikevičienė ◽  
Artūras Kilikevičius
Keyword(s):  
Experimental Research ◽  
Gas Flow ◽  
Collection Efficiency ◽  
Fine Particulate Matter ◽  
Air Flow ◽  
Gaseous Emissions ◽  
Channel System ◽  
Flow Parameters ◽  
The Impact ◽  
Channel Type

Cyclones are widely used for separating particles from gas in energy production objects. The efficiency of conventional centrifugal air cleaning devices ranges from 85 to 90%, but the weakness of many cyclones is the low collection efficiency of particles less than 10 μm in diameter. The novelty of this work is the research of the channel-type treatment device, with few levels adapted for precipitation of fine particulate matter, acting by a centrifugal and filtration principle. Many factors have an impact on cyclone efficiency—humidity, temperature, gas (air) composition, airflow velocity and etc. Many scientists evaluated only the effect of origin and size of PM on cyclone efficiency. The effect of gas (air) composition and temperature, and humidity on the multi-channel cyclone-separator efficiency still demands contributions. Complex theoretical and experimental research on air flow parameters and the efficiency of a cylindrical eight-channel system with adjustable half-rings for removing fine-dispersive particles (<20 μm) was carried out. The impact of air humidity and temperature on air flow, and gaseous smoke components on the removal of wood ashes was analyzed. The dusty gas flow was regulated. During the experiment, the average velocity of the cyclone was 16 m/s, and the temperature was 20–50 °C. The current paper presents experimental research results of wood ash removal in an eight-channel cyclone and theoretical methodology for the calculation of airflow parameters and cyclone effectiveness.

scholarly journals Mechanisms Responsible for Arc Cooling in Different Gases in Turbulent Nozzle Flow

2017 ◽  
Vol 4 (3) ◽  
pp. 234-240 ◽  
Author(s):  
Y. Guo ◽  
H. Zhang ◽  
Y. Yao ◽  
Q. Zhang ◽  
J. D. Yan
Keyword(s):  
Material Properties ◽  
High Speed ◽  
Gas Flow ◽  
Ohmic Heating ◽  
Circuit Breaker ◽  
Fault Current ◽  
High Current ◽  
Physical Mechanisms ◽  
Current Zero ◽  
Different Gases

A high voltage gas blast circuit breaker relies on the high speed gas flow in a nozzle to remove the energy due to Ohmic heating at high current and to provide strong arc cooling during the current zero period to interrupt a fault current. The physical mechanisms that are responsible for the hugely different arc cooling capabilities of two gases (SF<sub>6</sub> and air) are studied in the present work and important gas material properties controlling the cooling strength identified.

Hot gas flow analysis in SF/sub 6/ gas circuit breaker during the short circuit interruption

1989 ◽  
Vol 4 (3) ◽  
pp. 1757-1764 ◽  
Author(s):  
T. Yoshizumi ◽  
K. Ibuki ◽  
M. Hosomi ◽  
T. Yonezawa ◽  
H. Kawasaki
Keyword(s):  
Gas Flow ◽  
Short Circuit ◽  
Circuit Breaker ◽  
Flow Analysis ◽  
Hot Gas

scholarly journals Mathematical modeling of spatial gas flow in nozzles of nontrivial geometry

2021 ◽  
Vol 2094 (4) ◽  
pp. 042002
Author(s):  
S A Bitkin ◽  
M A Korepanov ◽  
M R Koroleva ◽  
A I Karpov ◽  
S S Makarov
Keyword(s):  
Gas Flow ◽  
Three Dimensional ◽  
Critical Section ◽  
Nozzle Geometry ◽  
Outlet Section ◽  
Flow Area ◽  
Flow Parameters ◽  
Inviscid Gas ◽  
Three Dimensional Models ◽  
The Mathematical Model

Abstract Numerical modeling of the spatial gas flow in an adjustable nozzle with an asymmetric critical section caused by the overlap of a part of the flow area by a gas flow regulator has been carried out. The mathematical model is based on three-dimensional models of gas dynamics, the method of large particles is used for calculation. When describing the unsteady flow of an inviscid gas, the system of Euler equations is used, written for a computational rectangular plane, taking into account the function of nozzle geometry. The results of calculations of flow parameters along a nozzle path with a uniform outlet section and with an obliquely cut outlet nozzle are presented. Calculations were carried out for completely open critical sections and for half overlapped. For oblique cut nozzles, the overlap of the critical section from the side of the short part and from the side of the long part of the oblique nozzle is considered.

Sign in / Sign up

Export Citation Format

Share Document