Large-signal S-parameters CAD technique applied to power amplifier design

Author(s):  
E. Kerherve ◽  
M. Hazouard ◽  
L. Courcelle ◽  
P. Jarry
Electronics ◽  
2021 ◽  
Vol 10 (3) ◽  
pp. 263
Author(s):  
Roberto Quaglia

In high-frequency power-amplifier design, it is common practice to approach the design of reactive matching networks using linear simulators and targeting a reflection loss limit (referenced to the target impedance). It is well known that this is only a first-pass design technique, since output power or efficiency contours do not correspond to mismatch circles. This paper presents a method to improve the accuracy of this approach in the case of matching network design for power amplifiers based on gallium nitride (GaN) technology. Equivalent mismatch circles, which lay within the power or efficiency contours targeted by the design, are analytically obtained thanks to geometrical considerations. A summary table providing the parameters to use for typical contours is provided. The technique is demonstrated on two examples of power-amplifier design on the 6–12 GHz band using the non-linear large-signal model of a GaN High Electron Mobility Transistor (HEMT).


2019 ◽  
Vol 30 ◽  
pp. 01011
Author(s):  
Vladimir Klokov ◽  
Nikolay Kargin ◽  
Alexander Garmash ◽  
Ekaterina Guzniaeva

The paper presents a description of design methodology for wide-band push-pull large-signal power amplifier based on GaN transistor with an output power of more than 10 W for high-performance Nonlinear Junction Detectors, which allows achieving optimal convergence of the theoretical model in practice, as well as increasing the efficiency of the power amplifier while maintaining a linear gain characteristic.


Author(s):  
Jialin Cai ◽  
Justin King ◽  
Shichang Chen ◽  
Meilin Wu ◽  
Jiangtao Su ◽  
...  

Abstract A novel, broadband, nonlinear behavioral model, based on support vector regression (SVR) is presented in this paper. The proposed model, distinct from existing SVR-based models, incorporates frequency information into its formalism, allowing the model to perform accurate prediction across a wide frequency band. The basic theory of the proposed model, along with model implementation and the model extraction procedure for radio frequency transistor devices is provided. The model is verified through comparisons with the simulation of an equivalent circuit model, as well as experimental measurements of a 10 W Gallium Nitride (GaN) transistor. It is seen that the efficiency prediction throughout the Smith chart, for varying fundamental and second harmonic loads, across a wideband frequency range, show excellent fidelity to the measured results. Device dc self-biasing is also modelled to allow prediction of power amplifier (PA) efficiency, which is shown to be highly accurate when compared with corresponding measured data. Finally, a class-J PA is constructed and measured across the frequency with a large-signal input tone. The resulting measured and modelled values of key PA performance figures are shown to be in excellent agreement, indicating the model is suitable for broadband PA design.


2010 ◽  
Vol 7 (22) ◽  
pp. 1672-1678
Author(s):  
Lin-Sheng Liu ◽  
Jian-Guo Ma ◽  
Geok-Ing Ng

2001 ◽  
Vol 49 (9) ◽  
pp. 1626-1633 ◽  
Author(s):  
Youngoo Yang ◽  
Young Yun Woo ◽  
Jaehyok Yi ◽  
Bumman Kim

2016 ◽  
Vol 26 (2) ◽  
pp. 128-130 ◽  
Author(s):  
Zhikai Chen ◽  
Yuehang Xu ◽  
Bin Zhang ◽  
Tangsheng Chen ◽  
Tao Gao ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document