Three-input single-output voltage-mode universal filter using single FDCCII

2014 ◽  
Author(s):  
Montree Kumngern
Keyword(s):  
Output Voltage ◽  
Universal Filter ◽  
Voltage Mode ◽  
Single Output

Five-inputs single-output voltage mode universal filter with high input and low output impedance using VDDDAs

Optik ◽  
2017 ◽  
Vol 128 ◽  
pp. 14-25 ◽  
Author(s):  
Surasak Sangyaem ◽  
Surapong Siripongdee ◽  
Winai Jaikla ◽  
Fabian Khateb
Keyword(s):  
Output Voltage ◽  
Output Impedance ◽  
Universal Filter ◽  
High Input ◽  
Voltage Mode ◽  
Single Output

NOVEL VOLTAGE-MODE UNIVERSAL FILTER USING ONLY TWO CDBAs

2005 ◽  
Vol 14 (01) ◽  
pp. 159-164 ◽  
Author(s):  
SUDHANSHU MAHESHWARI ◽  
IQBAL A. KHAN
Keyword(s):  
Pass Band ◽  
Universal Filter ◽  
Input Selection ◽  
Voltage Mode ◽  
Single Output ◽  
Control Computer ◽  
Low Pass ◽  
Band Pass ◽  
Pass Through ◽  
High Pass

A novel voltage-mode universal filter employing only two current differencing buffered amplifiers (CDBAs) is proposed. The filter uses four inputs and single output to realize six responses, viz. low-pass, high-pass, inverting band-pass, noninverting band-pass, band-elimination, and all-pass through input selection with independent pole-Q control. Computer simulation results using SPICE are also given to verify the theory.

scholarly journals Electronically Tunable TISO Voltage-Mode Universal Filter Using Two LT1228s

2021 ◽  
Vol 12 (1) ◽  
pp. 62-74
Author(s):  
May Phu Pwint Wai ◽  
Winai Jaikla ◽  
Surapong Siripongdee ◽  
Amornchai Chaichana ◽  
Peerawut Suwanjan
Keyword(s):  
Integrated Circuits ◽  
Harmonic Distortion ◽  
Input Voltage ◽  
Angular Frequency ◽  
Pass Band ◽  
Universal Filter ◽  
Voltage Mode ◽  
Single Output ◽  
Low Pass ◽  
Electronically Tunable

This study aims to design an electronically tunable voltage-mode (VM) universal filter utilizing commercially available LT1228 integrated circuits (ICs) with three-input and single-output (TISO) configuration. With the procedure based on two integrator loop filtering structures, the proposed filter consists of two LT1228s, four resistors, and two grounded capacitors. It realizes five filter output responses: low-pass, all-pass, band-reject, band-pass, and high-pass functions. By selecting input voltage signals, each output responses can be achieved without changing the circuit architecture. The natural angular frequency can be controlled electronically. The input voltage nodes Vin1 and Vin3 possess high impedance. The output node has low impedance, so it can be cascaded to other circuits. The performance of the proposed filter is corroborated by PSpice simulation and hardware implementation which support the theoretical assumptions. The result shows that the range of total harmonic distortion (THD) is lower than 1%, and that the higher the temperature is, the lower the natural angular frequency is.

scholarly journals Three-Input Single-Output Voltage-Mode Multifunction Filter with Electronic Controllability Based on Single Commercially Available IC

2017 ◽  
Vol 2017 ◽  
pp. 1-10 ◽  
Author(s):  
Supachai Klungtong ◽  
Dusit Thanapatay ◽  
Winai Jaikla
Keyword(s):  
Output Voltage ◽  
Matching Condition ◽  
Passive Component ◽  
Voltage Mode ◽  
Single Output ◽  
Rlc Circuit ◽  
Low Pass ◽  
Multifunction Filter ◽  
Component Matching ◽  
Technology Corporation

This paper presents a second-order voltage-mode filter with three inputs and single-output voltage using single commercially available IC, one resistor, and two capacitors. The used commercially available IC, called LT1228, is manufactured by Linear Technology Corporation. The proposed filter is based on parallel RLC circuit. The filter provides five output filter responses, namely, band-pass (BP), band-reject (BR), low-pass (LP), high-pass (HP), and all-pass (AP) functions. The selection of each filter response can be done without the requirement of active and passive component matching condition. Furthermore, the natural frequency and quality factor are electronically controlled. Besides, the nonideal case is also investigated. The output voltage node exhibits low impedance. The experimental results can validate the theoretical analyses.

Sign in / Sign up

Export Citation Format

Share Document