NOVEL VOLTAGE-MODE UNIVERSAL FILTER USING ONLY TWO CDBAs

2005 ◽  
Vol 14 (01) ◽  
pp. 159-164 ◽  
Author(s):  
SUDHANSHU MAHESHWARI ◽  
IQBAL A. KHAN
Keyword(s):  
Pass Band ◽  
Universal Filter ◽  
Input Selection ◽  
Voltage Mode ◽  
Single Output ◽  
Control Computer ◽  
Low Pass ◽  
Band Pass ◽  
Pass Through ◽  
High Pass

A novel voltage-mode universal filter employing only two current differencing buffered amplifiers (CDBAs) is proposed. The filter uses four inputs and single output to realize six responses, viz. low-pass, high-pass, inverting band-pass, noninverting band-pass, band-elimination, and all-pass through input selection with independent pole-Q control. Computer simulation results using SPICE are also given to verify the theory.

scholarly journals Third Order Universal Filter Using Single Operational Transresistance Amplifier

2013 ◽  
Vol 2013 ◽  
pp. 1-6 ◽  
Author(s):  
Mourina Ghosh ◽  
Sajal K. Paul ◽  
Rajiv Kumar Ranjan ◽  
Ashish Ranjan
Keyword(s):  
Cmos Technology ◽  
Pass Band ◽  
Universal Filter ◽  
Third Order ◽  
Operational Transresistance Amplifier ◽  
Single Output ◽  
Theoretical Design ◽  
Low Pass ◽  
Band Pass ◽  
High Pass

This paper proposes a multi-input single-output (MISO) third order voltage mode (VM) universal filter using only one operational transresistance amplifier (OTRA). The proposed circuit realizes low-pass, high-pass, all-pass, band-pass, and notch responses from the same topology. The PSPICE Simulation results using 0.5 μm CMOS technology agree well with the theoretical design.

A New Tunable SISO Filter Designed in 40nm CMOS for Bilateral Inverse and Buffer Filtering Applications

2021 ◽  
pp. 2150240
Author(s):  
Umar Mohammad ◽  
Fang Tang ◽  
Shu Zhou ◽  
Mohd Yusuf Yasin
Keyword(s):  
Simulation Analysis ◽  
Pass Band ◽  
Single Input Single Output ◽  
Change Of Direction ◽  
Single Output ◽  
Low Pass ◽  
Single Input ◽  
Band Pass ◽  
Parasitic Components ◽  
High Pass

A new study imitating the design and implementation of single-input–single-output (SISO) filters as bilateral filters has been presented in this paper. Second generation current controlled current conveyor (CCCII), being a popular low power active element was considered for the realization of the proposed design. Complete design, analysis and implementation of the voltage mode SISO filter was done using only two CCCII’s and two passive parasitic components. The striking feature of this work is that the proposed design can be made to work at either the input node or the output node, as well as in the cases; the change of direction changes the filter into an inverse filter and buffer filter. Basic filter applications like low-pass, high-pass, band-pass and band-stop were aimed to check the uniformity of the proposed design at different frequencies. Results perceived from the simulation study were fare enough on both the side nodes of the proposed design. Categorically, the circuit can be aimed to work in lieu of a filter transceiver. The consistency of the circuit was analyzed by the nodal analysis. Whereas the working performance was enormously analyzed and evaluated during the simulation analysis. The proposed design was simulated in HSPICE tool to exhibit and exploit the delivery, using the 45[Formula: see text]nm predictive technology model (PTM) parameters, with [Formula: see text][Formula: see text]V rail to rail voltages. Maximum power consumption of the circuit is around 138.5[Formula: see text][Formula: see text]W. Finally, the design was also implemented in Cadence Virtuoso using 40[Formula: see text]nm SMIC parameters.

Second-Order Voltage-Mode Universal Filters Using Two DVCCs, Two Grounded Capacitors and Four Resistors

2016 ◽  
Vol 25 (12) ◽  
pp. 1650154 ◽  
Author(s):  
Ahmet Abaci ◽  
Erkan Yuce
Keyword(s):  
Integrated Circuit ◽  
Matching Condition ◽  
Second Order ◽  
Point Of View ◽  
Pass Band ◽  
Current Conveyors ◽  
Voltage Mode ◽  
Low Pass ◽  
Band Pass ◽  
High Pass

In this paper, two new second-order voltage-mode universal filters are proposed. Both of the proposed filters use only two differential voltage current conveyors (DVCCs), four resistors and two grounded capacitors which are advantageous from integrated circuit technology point of view. They can simultaneously provide second-order low-pass, high-pass, band-pass, notch and all-pass responses. They offer orthogonal control of angular resonance frequency and quality factor. However, they have a single matching condition for only all-pass responses. A number of simulations based on SPICE program are accomplished in order to demonstrate the performance of both filters.

A NEW ELECTRONICALLY-TUNABLE ACTIVE-ONLY UNIVERSAL BIQUAD

2011 ◽  
Vol 20 (03) ◽  
pp. 549-555 ◽  
Author(s):  
A. K. SINGH ◽  
R. SENANI ◽  
D. R. BHASKAR ◽  
R. K. SHARMA
Keyword(s):  
Pass Band ◽  
Voltage Mode ◽  
Op Amp ◽  
Op Amps ◽  
Reasonable Number ◽  
Low Pass ◽  
Band Pass ◽  
Electronically Tunable ◽  
High Pass ◽  
Realization Condition

A number of configurations for realizing voltage-mode (VM) biquads using op-amps and OTAs have been presented in the literature, however, none of these provide the following desirable properties simultaneously: (i) realizability of all the five standard filters (namely; low pass, high pass, band pass, band stop and all pass), (ii) tunability of all the three filter parameters (namely; ω0, bandwidth or Q0 and gain) and (iii) not requiring any realization condition in any of the five filter responses. This paper presents a new configuration which does possess all the above mentioned desirable properties simultaneously while using only two internally-compensated type op-amps and a reasonable number of OTAs. The workability of the new configuration has been demonstrated by SPICE simulations based upon CMOS Op-amp and CMOS OTAs.

scholarly journals Electronically Tunable TISO Voltage-Mode Universal Filter Using Two LT1228s

2021 ◽  
Vol 12 (1) ◽  
pp. 62-74
Author(s):  
May Phu Pwint Wai ◽  
Winai Jaikla ◽  
Surapong Siripongdee ◽  
Amornchai Chaichana ◽  
Peerawut Suwanjan
Keyword(s):  
Integrated Circuits ◽  
Harmonic Distortion ◽  
Input Voltage ◽  
Angular Frequency ◽  
Pass Band ◽  
Universal Filter ◽  
Voltage Mode ◽  
Single Output ◽  
Low Pass ◽  
Electronically Tunable

This study aims to design an electronically tunable voltage-mode (VM) universal filter utilizing commercially available LT1228 integrated circuits (ICs) with three-input and single-output (TISO) configuration. With the procedure based on two integrator loop filtering structures, the proposed filter consists of two LT1228s, four resistors, and two grounded capacitors. It realizes five filter output responses: low-pass, all-pass, band-reject, band-pass, and high-pass functions. By selecting input voltage signals, each output responses can be achieved without changing the circuit architecture. The natural angular frequency can be controlled electronically. The input voltage nodes Vin1 and Vin3 possess high impedance. The output node has low impedance, so it can be cascaded to other circuits. The performance of the proposed filter is corroborated by PSpice simulation and hardware implementation which support the theoretical assumptions. The result shows that the range of total harmonic distortion (THD) is lower than 1%, and that the higher the temperature is, the lower the natural angular frequency is.

scholarly journals Voltage Mode Universal Biquad Using CCCII

2011 ◽  
Vol 2011 ◽  
pp. 1-5 ◽  
Author(s):  
Ashish Ranjan ◽  
Sajal K. Paul
Keyword(s):  
Pass Band ◽  
Current Conveyors ◽  
Ic Design ◽  
Passive Components ◽  
Voltage Mode ◽  
Single Output ◽  
Low Pass ◽  
Minimum Number ◽  
Band Pass ◽  
Low Sensitivity

This paper proposes a multi-input single-output (MISO) second-order active-C voltage mode (VM) universal filter using two second-generation current-controlled current conveyors (CCCIIs) and two equal-valued capacitors. The proposed circuit realizes low pass, band pass, high pass, all pass, and notch responses from the same topology. The filter uses-minimum number of passive components and no resistor which is suitable for IC Design. The filter enjoys low-sensitivity performance and exhibits electronic and orthogonal tunability of pole frequency () and quality factor () via bias current of CCCIIs. PSPICE simulation results confirm the theory.

scholarly journals One-Input Three-Output Current-Mode Universal Filter Using Translinear Current Conveyors

2019 ◽  
Vol 2 (4) ◽  
pp. 101
Author(s):  
Montree Kumngern
Keyword(s):  
Current Mode ◽  
Pass Band ◽  
Current Conveyors ◽  
Current Response ◽  
Universal Filter ◽  
Low Pass ◽  
Band Pass ◽  
Active Matching ◽  
High Output Impedance ◽  
High Pass

This paper presents a new current-mode universal filter with one-input three-output employing three translinear current conveyors and two grounded capacitors. The proposed filter provides low-pass, band-pass, high-pass current response with high output impedance output which can be directly connected for current-mode circuit. The band-pass and all-pass filters can also be obtained. The parameters wo and Q can be controlled separately and electronically by the bias currents of current conveyors. For realizing all filtering functions, no passive and active matching conditions are required. The active and passive sensitivities are low. The characteristic of the proposed circuit can be confirmed by SPICE simulations.

scholarly journals DDCCTA-Based Universal filter and Quadrature Oscillator

2018 ◽  
Vol 3 (2) ◽  
pp. 18-21
Author(s):  
Rashmika Rai ◽  
◽  
S Indu
Keyword(s):  
Integrated Circuit ◽  
Notch Filter ◽  
Pass Band ◽  
Universal Filter ◽  
Passive Components ◽  
Transconductance Amplifier ◽  
Low Pass ◽  
Single Input ◽  
Band Pass ◽  
High Pass

The study presents a universal filter and Oscillator obtain by applying only single input. All the passive components used are grounded which is suitable for integrated circuit implementation. In the circuit by applying for single input simultaneously low pass, High Pass, Band Pass, All Pass, and Notch filter is obtained by using two blocks of Differential Difference current conveyor transconductance amplifier.

scholarly journals Voltage Differencing Current Conveyor Based Voltage-Mode and Current-Mode Universal Biquad Filters with Electronic Tuning Facility

2021 ◽  
Vol 11 (2) ◽  
pp. 146-160
Author(s):  
Suvajit Roy ◽  
Tapas Kumar Paul ◽  
Saikat Maiti ◽  
Radha Raman Pal
Keyword(s):  
Supply Voltage ◽  
Current Mode ◽  
Current Conveyor ◽  
Pass Band ◽  
Voltage Mode ◽  
Single Output ◽  
Electronic Tuning ◽  
Low Pass ◽  
Single Input ◽  
Band Pass

The objective of this study is to present four new universal biquad filters, two voltage-mode multi-input-single-output (MISO), and two current-mode single-input-multi-output (SIMO). The filters employ one voltage differencing current conveyor (VDCC) as an active element and two capacitors along with two resistors as passive elements. All the five filter responses, i.e., high-pass, low-pass, band-pass, band-stop, and all-pass responses, are obtained from the same circuit topology. Moreover, the pole frequency and quality factor are independently tunable. Additionally, they do not require any double/inverted input signals for response realization. Furthermore, they enjoy low active and passive sensitivities. Various regular analyses support the design ideas. The functionality of the presented filters are tested by PSPICE simulations using TSMC 0.18 µm technology parameters with ± 0.9 V supply voltage. The circuits are also justified experimentally by creating the VDCC block using commercially available OPA860 ICs. The experimental and simulation results agree well with the theoretically predicted results.

Sign in / Sign up

Export Citation Format

Share Document