Graphene-Based Ammonia-Gas Sensor Using In-Fiber Mach-Zehnder Interferometer

2017 ◽  
Vol 29 (23) ◽  
pp. 2035-2038 ◽  
Author(s):  
Ting Hao ◽  
Kin Seng Chiang
2017 ◽  
Vol 7 (1) ◽  
Author(s):  
Xinyue Huang ◽  
Xueming Li ◽  
Jianchun Yang ◽  
Chuanyi Tao ◽  
Xiaogang Guo ◽  
...  

Sensors ◽  
2021 ◽  
Vol 21 (11) ◽  
pp. 3886
Author(s):  
Xiaofeng Fan ◽  
Shuying Deng ◽  
Zhongchao Wei ◽  
Faqiang Wang ◽  
Chunhua Tan ◽  
...  

A graphene oxide-coated in-fiber Mach-Zehnder interferometer (MZI) formed with a multimode fiber-thin core fiber-multimode fiber (MMF-TCF-MMF) is proposed and experimentally demonstrated for ammonia gas (NH3) sensing. The MZI structure is composed of two segments of MMF of length 2 mm, with a flame-tapered TCF between them as the sensing arm. The MMFs act as mode couplers to split and recombine light owing to the core diameter mismatch with the other fibers. A tapered TCF is formed by the flame melting taper method, resulting in evanescent wave leakage. A layer of graphene oxide (GO) is applied to the tapered region of the TCF to achieve gas adsorption. The sensor operates on the principle of changing the effective refractive index of the cladding mode of a fiber through changing the conductivity of the GO coating by adsorbed NH3 molecules, which gives rise to a phase shift and shows as the resonant dip shifts in the transmission spectrum. So the concentration of the ammonia gas can be obtained by measuring the dip shift. A wavelength-shift sensitivity of 4.97 pm/ppm with a linear fit coefficient of 98.9% is achieved for ammonia gas concentrations in the range of 0 to 151 ppm. In addition, we performed a repetitive dynamic response test on the sensor by charging/releasing NH3 at concentration of 200 ppm and a relative humidity test in a relative humidity range of 35% to 70%, which demonstrates the reusability and stability of the sensor.


Photonics ◽  
2021 ◽  
Vol 9 (1) ◽  
pp. 8
Author(s):  
Raghi S. El Shamy ◽  
Mohamed A. Swillam ◽  
Mohamed M. ElRayany ◽  
Alaa Sultan ◽  
Xun Li

In this paper, we propose a compact optical gas sensor based on the widespread silicon-on-insulator (SOI) technology, operating in the near-infrared (NIR) region around the 1.55 µm wavelength. The sensor employs a loop-terminated Mach–Zehnder interferometer (LT-MZI) with a slot waveguide and a strip waveguide for the sensing arm and the reference arm, respectively. For the same arm length, the LT-MZI can achieve a detection limit two times lower than that of the conventional MZI. Different sensor components were designed, and the optimum dimensions were obtained using finite-difference eigenmode (FDE) and finite-difference time-domain (FDTD) solvers. With a sensing arm length of only 150 μm, our sensor achieves a device sensitivity of 1070 nm/RIU and a figure-of-merit (FOM) as high as 280.8 RIU−1 at the 1.55 μm wavelength. Higher values of FOM can be attained by employing a longer sensing arm. The whole sensor is subjected to air cladding; thus, there is no need for oxide deposition and a further lithography step for sensing-area patterning. The sensor is well suited for low-cost fabrication and large-scale production. Finally, the same LT-MZI device with strip and slot arms but with oxide cladding was fabricated and characterized. The measurements were in good agreement with the electromagnetic (EM) simulation results, ensuring the reliability of our proposed design.


2014 ◽  
Vol 1 (4) ◽  
pp. 16-19
Author(s):  
Vivek Talwar ◽  
◽  
Ravi Chand Singh ◽  

Author(s):  
Priya Gupta ◽  
Savita Maurya ◽  
Narendra Kumar Pandey ◽  
Vernica Verma

: This review paper encompasses a study of metal-oxide and their composite based gas sensors used for the detection of ammonia (NH3) gas. Metal-oxide has come into view as an encouraging choice in the gas sensor industry. This review paper focuses on the ammonia sensing principle of the metal oxides. It also includes various approaches adopted for increasing the gas sensitivity of metal-oxide sensors. Increasing the sensitivity of the ammonia gas sensor includes size effects and doping by metal or other metal oxides which will change the microstructure and morphology of the metal oxides. Different parameters that affect the performances like sensitivity, stability, and selectivity of gas sensors are discussed in this paper. Performances of the most operated metal oxides with strengths and limitations in ammonia gas sensing application are reviewed. The challenges for the development of high sensitive and selective ammonia gas sensor are also discussed.


Sign in / Sign up

Export Citation Format

Share Document