A Method for Correlating the Influence of External Crossflow on the Discharge Coefficients of Film Cooling Holes

2000 ◽  
Vol 123 (2) ◽  
pp. 258-265 ◽  
Author(s):  
D. A. Rowbury ◽  
M. L. G. Oldfield ◽  
G. D. Lock
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
Discharge Coefficient ◽  
Guide Vane ◽  
Discharge Coefficients ◽  
Nozzle Guide Vane ◽  
Aero Engine ◽  
Nozzle Guide ◽  
Film Cooling Holes ◽  
Asme Paper

An empirical means of predicting the discharge coefficients of film cooling holes in an operating engine has been developed. The method quantifies the influence of the major dimensionless parameters, namely hole geometry, pressure ratio across the hole, coolant Reynolds number, and the freestream Mach number. The method utilizes discharge coefficient data measured on both a first-stage high-pressure nozzle guide vane from a modern aero-engine and a scale (1.4 times) replica of the vane. The vane has over 300 film cooling holes, arranged in 14 rows. Data was collected for both vanes in the absence of external flow. These noncrossflow experiments were conducted in a pressurized vessel in order to cover the wide range of pressure ratios and coolant Reynolds numbers found in the engine. Regrettably, the proprietary nature of the data collected on the engine vane prevents its publication, although its input to the derived correlation is discussed. Experiments were also conducted using the replica vanes in an annular blowdown cascade which models the external flow patterns found in the engine. The coolant system used a heavy foreign gas (SF6 /Ar mixture) at ambient temperatures which allowed the coolant-to-mainstream density ratio and blowing parameters to be matched to engine values. These experiments matched the mainstream Reynolds and Mach numbers and the coolant Mach number to engine values, but the coolant Reynolds number was not engine representative (Rowbury, D. A., Oldfield, M. L. G., and Lock, G. D., 1997, “Engine-Representative Discharge Coefficients Measured in an Annular Nozzle Guide Vane Cascade,” ASME Paper No. 97-GT-99, International Gas Turbine and Aero-Engine Congress & Exhibition, Orlando, Florida, June 1997; Rowbury, D. A., Oldfield, M. L. G., Lock, G. D., and Dancer, S. N., 1998, “Scaling of Film Cooling Discharge Coefficient Measurements to Engine Conditions,” ASME Paper No. 98-GT-79, International Gas Turbine and Aero-Engine Congress & Exhibition, Stockholm, Sweden, June 1998). A correlation for discharge coefficients in the absence of external crossflow has been derived from this data and other published data. An additive loss coefficient method is subsequently applied to the cascade data in order to assess the effect of the external crossflow. The correlation is used successfully to reconstruct the experimental data. It is further validated by successfully predicting data published by other researchers. The work presented is of considerable value to gas turbine design engineers as it provides an improved means of predicting the discharge coefficients of engine film cooling holes.

Engine Representative Discharge Coefficients Measured in an Annular Nozzle Guide Vane Cascade

1997 ◽  
Author(s):  
D. A. Rowbury ◽  
M. L. G. Oldfield ◽  
G. D. Lock
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Density Ratio ◽  
External Flow ◽  
Surprising Result ◽  
Crossover Effect ◽  
Discharge Coefficients ◽  
Nozzle Guide Vane ◽  
Nozzle Guide ◽  
Film Cooling Holes

This paper discusses measurements of the discharge coefficients of gas turbine nozzle guide vane film cooling holes under fully engine representative conditions. These unique experiments were carried out in a large scale annular blowdown cascade which models the three-dimensional external, flow patterns found in modern aero-engines, including all secondary flow phenomena. Furthermore, the coolant system design allows the coolant-to-mainstream density ratio and blowing parameter to be matched to engine values, although they can be independently varied. The results confirm that the discharge coefficients of film cooling holes are significantly altered by external crossflow. The discharge coefficient is usually reduced by external crossflow, but under certain external flow conditions it can be increased over the non-crossflow case. This previously unhightighted phenomenon has been termed ‘the crossover effect’, and, although an initially surprising result, is of importance to aero-engine designers as taking account of it should lead to improved predictions of coolant consumption. As a consequence, more uniform blade cooling should be achieved and, in turn, the attainment of greater component durability will be possible.

The Effects of High Mainstream Turbulence and Turbine Vane Film Cooling on the Dispersion of a Simulated Hot Streak

2003 ◽  
Author(s):  
Sean Jenkins ◽  
Krishnakumar Varadarajam ◽  
David G. Bogard
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Suction Side ◽  
Peak Temperature ◽  
Nozzle Guide Vane ◽  
Turbulence Effects ◽  
High Turbulence ◽  
Nozzle Guide ◽  
Hot Streak ◽  
Film Cooling Holes

This paper presents the combined effects of high turbulence and film cooling on the dispersion of a simulated hot streak as it passes over a scaled-up nozzle guide vane. Experimental data demonstrates a considerable decay in the strength of a hot streak due to turbulence effects alone. Film cooling further reduces the peak temperature values resulting in a reduction of the peak temperature in the hot streak on the order of 75% relative to the upstream peak temperature in the hot streak. Comparisons are made between high turbulence (Tu = 20%) and moderate turbulence (Tu = 3.5%) as well as between different blowing conditions for the suction side, showerhead, and pressure side film cooling holes on a simulated nozzle guide vane.

Multi-Fidelity Modelling of a Fully-Featured HP Turbine Stage

2017 ◽  
Author(s):  
Giorgio Occhioni ◽  
Shahrokh Shahpar ◽  
Haidong Li
Keyword(s):  
High Pressure ◽  
Film Cooling ◽  
State Of The Art ◽  
Guide Vane ◽  
Phase Lag ◽  
Turbine Stage ◽  
High Pressure Turbine ◽  
Nozzle Guide Vane ◽  
Nozzle Guide ◽  
Film Cooling Holes

An improvement in overall efficiency and power output for gas turbine engines can be obtained by increasing the combustor exit temperature, but the thermal management of metal parts exposed to hot gases is challenging. Discrete film cooling, combined with internal convective cooling is the current state-of-the-art available to aerothermal designers of these components. To simplify the simulation problem in the aerodynamic design phase, it is common practice to replace the cooling holes with source strips applied to the blade. This could lead to inaccuracies in high pressure turbine performance prediction. This study has been carried out on a fully-featured high pressure turbine stage using high-fidelity simulations. The film cooling holes on the nozzle guide vane and on the rotor are initially modelled using a strip model approach. Then, to increase the model fidelity, the strips on the suction side of the rotor are replaced with discrete fan shaped film cooling holes. A rigid body rotation is also applied to the nozzle guide vane to vary the stage capacity and reaction. The effects of the mesh topology & resolution are also taken into account. The results obtained with these two approaches are then compared, giving the designers a better understanding on film cooling modelling and relationship between capacity, reaction and performance. The accurate prediction of the complex interaction between cavity inflows and the main-flow, still represent a challenge for the state of the art RANS solvers. Hence, an unsteady phase-lag approach has been used to overcome the RANS limitations. A validation of the unsteady solutions has been carried out with respect to experimental data.

Aerodynamic and Endwall Film-Cooling Investigations of a Gas Turbine Nozzle Guide Vane Applying Temperature-Sensitive Paint

2011 ◽  
Vol 133 (3) ◽  
Author(s):  
Martin Kunze ◽  
Konrad Vogeler ◽  
Glenn Brown ◽  
Chander Prakash ◽  
Kenneth Landis
Keyword(s):  
Heat Conduction ◽  
Gas Turbine ◽  
Film Cooling ◽  
Guide Vane ◽  
Temperature Sensitive ◽  
Test Plate ◽  
Nozzle Guide Vane ◽  
Temperature Sensitive Paint ◽  
Nozzle Guide ◽  
Endwall Film Cooling

Endwall film-cooling investigations are conducted with a single row of fan-shaped holes in a low-speed, six-bladed linear cascade. The incidence of the inlet flow was changed between −5 deg and 40 deg to achieve higher loading conditions, which results in an intensification of the secondary flow and enhanced interaction with the injected coolant. The investigated profile is based on a near-hub section of the nozzle guide vane of a highly loaded gas turbine. The aerodynamic performance was investigated using pneumatic probes. The film-cooling effectiveness distribution is determined using the temperature-sensitive paint technique. Carbon dioxide was used as coolant to provide elevated density ratios of about 1.4. Although low thermal conductivity material is used for the endwall test plate, the measured temperature fields show influences of 3D-heat conduction inside the test plate. To measure film effectiveness and the heat transfer separately, an adiabatic test surface is needed. Therefore, the effects of heat conduction are modeled using the finite-element-method. With the resulting convective heat flux pattern derived from the computations, the endwall film-cooling measurements are corrected. Furthermore, this approach is applied to evaluate the heat loss inside the holes and the film discharge temperature at the hole exit.

The Effects of High Mainstream Turbulence and Turbine Vane Film Cooling on the Dispersion of a Simulated Hot Streak

2004 ◽  
Vol 126 (1) ◽  
pp. 203-211 ◽  
Author(s):  
Sean Jenkins ◽  
Krishnakumar Varadarajan ◽  
David G. Bogard
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Suction Side ◽  
Peak Temperature ◽  
Nozzle Guide Vane ◽  
Turbulence Effects ◽  
High Turbulence ◽  
Nozzle Guide ◽  
Hot Streak ◽  
Film Cooling Holes

This paper presents the combined effects of high turbulence and film cooling on the dispersion of a simulated hot streak as it passes over a scaled-up nozzle guide vane. Experimental data demonstrates a considerable decay in the strength of a hot streak due to turbulence effects alone. Film cooling further reduces the peak temperature values resulting in a reduction of the peak temperature in the hot streak on the order of 75% relative to the upstream peak temperature in the hot streak. Comparisons are made between high turbulence Tu=20% and moderate turbulence Tu=3.5% as well as between different blowing conditions for the suction side, showerhead, and pressure side film cooling holes on a simulated nozzle guide vane.

Contoured Endwall Flow and Heat Transfer Experiments With Combustor Coolant and Gap Leakage Flows for a Turbine Nozzle Guide Vane

2016 ◽  
Author(s):  
Reema Saxena ◽  
Mahmood H. Alqefl ◽  
Zhao Liu ◽  
Hee-Koo Moon ◽  
Luzeng Zhang ◽  
...  
Keyword(s):  
High Pressure ◽  
Gas Turbine ◽  
Mass Flow ◽  
Film Cooling ◽  
Thermal Loading ◽  
Guide Vane ◽  
Nozzle Guide Vane ◽  
Adiabatic Effectiveness ◽  
Interfacial Gap ◽  
Nozzle Guide

Flow in a high pressure gas turbine passage is complex, involving systems of secondary vortex flows and strong transverse pressure gradients. This complexity causes difficulty in providing film cooling coverage to the hub endwall region, which is subjected to high thermal loading due to combustor exit hot core gases. Therefore, an improved understanding of these flow features and their effects on endwall film cooling is needed to assist designers in developing efficient cooling schemes. The experimental study presented in this paper is performed on a linear, stationary, two-passage cascade representing the first stage nozzle guide vane of a high-pressure gas turbine. The sources of film cooling flows are the upstream combustor liner coolant and the leakage flow from the combustor-nozzle guide vane interfacial gap. Measurements are performed on an axisymmetrically-contoured endwall passage under conditions of various leakage mass flow rates to mainstream flow ratios (MFR= 0.5%, 1.0%, 1.5%). Flow migration and mixing are documented by measuring passage thermal fields and adiabatic effectiveness values over the endwall. It is found that, compared to our previous studies with a rotor inlet leakage slot geometry, the thin slot geometry of the nozzle leakage path gives a more uniform coolant spread over the endwall with significant coverage reaching the downstream and pressure-side regions of the passage. Interestingly, the coverage is seen to be only weakly dependent on the leakage mass low ratio and even reduce slightly with an increase in mass flow ratio above 1%, as indicated by lowered endwall adiabatic effectiveness values.

Aerodynamic and End-Wall Film Cooling Investigations of a Gas Turbine Nozzle Guide Vane Applying Temperature-Sensitive Paint

2009 ◽  
Author(s):  
Martin Kunze ◽  
Konrad Vogeler ◽  
Glenn Brown ◽  
Chander Prakash ◽  
Kenneth Landis
Keyword(s):  
Heat Conduction ◽  
Gas Turbine ◽  
Film Cooling ◽  
Guide Vane ◽  
Temperature Sensitive ◽  
Test Plate ◽  
Nozzle Guide Vane ◽  
Temperature Sensitive Paint ◽  
Nozzle Guide ◽  
Endwall Film Cooling

This paper presents endwall film cooling investigations with a single row of fanshaped holes in a low-speed, six-bladed linear cascade. The variation of the cascade loading was achieved by changing the incidence. The investigated profile is based on a nozzle guide vane of a highly loaded gas turbine. The aerodynamic performance was investigated using pneumatic probes. The film-cooling effectiveness distribution is determined using the temperature-sensitive paint technique (TSP). Carbon dioxide was used as coolant to provide elevated density ratios of about 1.4. Although low thermal conductivity material is used for the endwall test plate, the measured temperature fields show influences of 3D heat conduction inside the test plate. To measure film effectiveness and the heat transfer separately, an adiabatic test surface is needed. Therefore the effects of heat conduction are modeled using the FE-method. With the resulting convective heat flux pattern derived from the computations, the endwall film cooling measurements are corrected. Furthermore this approach is applied to evaluate the heat loss inside the holes and the film discharge temperature at the hole exit.

Application of Unsteady CFD Methods to Trailing Edge Cutback Film Cooling

2014 ◽  
Author(s):  
S. Ravelli ◽  
G. Barigozzi
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Navier Stokes ◽  
Trailing Edge ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Nozzle Guide Vane ◽  
Unsteady Rans ◽  
Exit Mach Number ◽  
Nozzle Guide

The main purpose of this numerical investigation is to overcome the limitations of the steady modeling in predicting the cooling efficiency over the cutback surface in a high pressure turbine nozzle guide vane. Since discrepancy between Reynolds-averaged Navier–Stokes (RANS) predictions and measured thermal coverage at the trailing edge was attributable to unsteadiness, Unsteady RANS (URANS) modeling was implemented to evaluate improvements in simulating the mixing between the mainstream and the coolant exiting the cutback slot. With the aim of reducing the computation effort, only a portion of the airfoil along the span was simulated at an exit Mach number of Ma2is = 0.2. Three values of the coolant-to-mainstream mass flow ratio were considered: MFR = 0.66%, 1.05%, and 1.44%. Nevertheless the inherent vortex shedding from the cutback lip was somehow captured by the URANS method, the computed mixing was not enough to reproduce the measured drop in adiabatic effectiveness η along the streamwise direction, over the cutback surface. So modeling was taken a step further by using the Scale Adaptive Simulation (SAS) method at MFR = 1.05%. Results from the SAS approach were found to have potential to mimic the experimental measurements. Vortices shedding from the cutback lip were well predicted in shape and magnitude, but with a lower frequency, as compared to PIV data and flow visualizations. Moreover, the simulated reduction in film cooling effectiveness toward the trailing edge was similar to that observed experimentally.

Research of Aerodynamic Performance of HP-Turbine with Coolant Injections for Variable Cycle Engine

2011 ◽  
Vol 110-116 ◽  
pp. 1047-1053
Author(s):  
Zhi Gang Liu ◽  
Xiang Jun Fang ◽  
Si Yong Liu ◽  
Ping Wang ◽  
Zhao Yin
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Supersonic Nozzle ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Thermodynamic Cycle ◽  
Aerodynamic Performance ◽  
Nozzle Guide Vane ◽  
Nozzle Guide ◽  
Transonic Rotor

A highly loaded high-pressure turbine with a supersonic nozzle guide vane and a transonic rotor for a Variable Cycle Engine (VCE) has been investigated. Film cooling strategies were designed for the whole stage, during which the positions, injection orientations and arrangements of cooling holes were confirmed. Three-dimensional steady numerical simulations have been performed in the two operation modes of low and high bypass ratio with different thermodynamic cycle parameters according to the VCE and the coolant injections have been simulated by means of additional source term method. The influences of coolant injections in the fully cooled turbine stage on aerodynamic performance and flow characteristics have been analyzed. The results indicate that, the supersonic nozzle guide vane, over-expansion degree of main flows, fluctuations of static pressure and intensity of corner vortex are lessened or alleviated. In the transonic rotor, expansion and doing work capabilities in the mixed fluid are strengthened. Proper coolants injections are beneficial to the flow characteristics in the blade passage.

Sign in / Sign up

Export Citation Format

Share Document