Studies on a Horizontal Axis Wind Turbine With Passive Pitch-Flap Mechanism (Performance and Flow Analysis Around Wind Turbine)

2001 ◽  
Vol 123 (3) ◽  
pp. 516-522 ◽  
Author(s):  
Yukimaru Shimizu ◽  
Yasunari Kamada
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Flow Pattern ◽  
Output Power ◽  
Flow Analysis ◽  
Horizontal Axis ◽  
Coupling Mechanism ◽  
Passive System ◽  
Horizontal Axis Wind Turbine ◽  
Breaking Effect

This paper describes the development of a passive system to control the output power of a horizontal axis wind turbine. This pitch-flap coupling mechanism can reduce rotor power above rated wind speed. This mechanism has two kinds of blade motions: the flapping and the pitching motions. In this paper, braking effects are investigated experimentally. It is found that the breaking effect is improved when the ratio of pitch to flap motions is large. Also, the flow pattern around the wind turbine is investigated. It is found that the braking effects are caused by a couple of ring vortices.

Effect of Wind Speed and Blade Deflection Angle on the Output Power of Horizontal-Axis Wind Turbines

2018 ◽  
Vol 6 (2) ◽  
pp. 75-81
Author(s):  
Muhammad Al Badri
Keyword(s):  
Wind Speed ◽  
Wind Energy ◽  
Wind Turbine ◽  
Output Power ◽  
Deflection Angle ◽  
Maximum Output Power ◽  
Simulation Software ◽  
Horizontal Axis ◽  
Maximum Output ◽  
Horizontal Axis Wind Turbine

This study is aimed to optimize the conversion of kinetic wind energy into electrical energy. Wind energy is a sustainable energy that is preferred to generate electricity for its low generation cost and low CO2 emissions. The considerations of physical principles of a horizontal axis wind turbine were involved in the study. Controlling of the blade angle deviation and the turbine rotation direction was also considered. For this purpose, a complete wind turbine system was setup by using the computerized simulation software (PSCAD). The system was running at five different cases with different wind speeds and different angles of the blade. The system was successfully generating a maximum output power from the wind turbine based on the changing of the deflection angle of the blade. Also the system would shut down if there were no matching between the wind speed and its direction with the angle of the blade.

scholarly journals PENGARUH VARIASI JUMLAH BLADE TURBIN ANGIN TERHADAP OUTPUT DAYA LISTRIK

2014 ◽  
Vol 4 (1) ◽  
Author(s):  
I Kade Wiratama ◽  
Made Mara ◽  
Arif Mulyanto ◽  
Muliadi Harianhady
Keyword(s):  
Wind Speed ◽  
Wind Energy ◽  
Wind Turbine ◽  
Output Power ◽  
Electrical Energy ◽  
Horizontal Axis ◽  
Horizontal Axis Wind Turbine ◽  
Generating Equipment ◽  
Electrical Output

Some area in Indonesia such as southern part of Sumatra to Nusa Tenggara have big enough wind speed to produce electrical energy by using wind turbine. However, the potential resources are not yet fully developed, and only 1.4 GW electrical energy has been generating in the Indonesia region. Most of the wind energy generating equipment is designed to the European wind speed which is   10 - 30 knot. So, it is very important to modify the such equipment to be able to implement in Indonesia area which is have a lower wind speed.The purpose of this research is to know the influence of number of blades and wind speed to electricity generated by horizontal axis wind turbine with blade taper inversed linear.The result showed that the highest electrical output power was 2,02 watt produced by 5 blades and 3,5 m/s wind speed. The lowest electrical output power was 2,347 watt achieved by using 3 blades and 2,5 m/s wind speed.

scholarly journals Perancangan Prototipe Turbin Angin Sumbu Horizontal Skala Laboratorium Dengan Inverter

2021 ◽  
Vol 1 (1) ◽  
pp. 24-29
Author(s):  
Najma Safienatin Najah ◽  
Arief Muliawan ◽  
Febria Anita
Keyword(s):  
Wind Turbine ◽  
Output Power ◽  
Design Research ◽  
Horizontal Axis ◽  
Horizontal Axis Wind Turbine ◽  
Research Results ◽  
Turn On ◽  
Generator Voltage ◽  
Turbine Design ◽  
Generator Currents

A horizontal axis wind turbine design research has been carried out using an inverter. This study aims to generate the output power generated by the generator through an inverter. So that the use of an inverter can turn on the 10 watt lamp. From the research results obtained turbine rotation varied between 1357 rpm to 2415 rpm producing a generator voltage of 3.05 volts to 4.61 volts and generator currents 32mA up to 49 mA. The inverter produces a voltage of 16.57 volts up to 20.46 volts and an inverter current of 0.60 amperes up to 0.48 amperes. The greater the rotation of the wind turbine turbine, the greater the generator voltage generated and so is the voltage of the inverter. While the current will increase as the turbine rotation increases and the inverse of the inverter current will decrease as the turbine rotation increases.

Numerical Studies of the Effects of Active and Passive Circulation Enhancement Concepts on Wind Turbine Performance

2006 ◽  
Vol 128 (4) ◽  
pp. 432-444 ◽  
Author(s):  
Chanin Tongchitpakdee ◽  
Sarun Benjanirat ◽  
Lakshmi N. Sankar
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Flow Analysis ◽  
Three Dimensional ◽  
Turbine Rotor ◽  
Horizontal Axis Wind Turbine ◽  
Trailing Edge ◽  
Low Wind Speed ◽  
Gurney Flap ◽  
Coanda Jet

The aerodynamic performance of a wind turbine rotor equipped with circulation enhancement technology (trailing-edge blowing or Gurney flaps) is investigated using a three-dimensional unsteady viscous flow analysis. The National Renewable Energy Laboratory Phase VI horizontal axis wind turbine is chosen as the baseline configuration. Experimental data for the baseline case is used to validate the flow solver, prior to its use in exploring these concepts. Calculations have been performed for axial and yawed flow at several wind conditions. Results presented include radial distribution of the normal and tangential forces, shaft torque, root flap moment, and surface pressure distributions at selected radial locations. At low wind speed (7m∕s) where the flow is fully attached, it is shown that a Coanda jet at the trailing edge of the rotor blade is effective at increasing circulation resulting in an increase of lift and the chordwise thrust force. This leads to an increased amount of net power generation compared to the baseline configuration for moderate blowing coefficients (Cμ⩽0.075). A passive Gurney flap was found to increase the bound circulation and produce increased power in a manner similar to Coanda jet. At high wind speed (15m∕s) where the flow is separated, both the Coanda jet and Gurney flap become ineffective. The effects of these two concepts on the root bending moments have also been studied.

scholarly journals Investigation of an Innovative Rotor Modification for a Small-Scale Horizontal Axis Wind Turbine

Energies ◽  
2020 ◽  
Vol 13 (10) ◽  
pp. 2649 ◽  
Author(s):  
Artur Bugała ◽  
Olga Roszyk
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Cfd Simulation ◽  
Turbine Blades ◽  
Three Dimensional ◽  
Horizontal Axis ◽  
Power Coefficient ◽  
Small Scale ◽  
Horizontal Axis Wind Turbine ◽  
Airflow Distribution

This paper presents the results of the computational fluid dynamics (CFD) simulation of the airflow for a 300 W horizontal axis wind turbine, using additional structural elements which modify the original shape of the rotor in the form of multi-shaped bowls which change the airflow distribution. A three-dimensional CAD model of the tested wind turbine was presented, with three variants subjected to simulation: a basic wind turbine without the element that modifies the airflow distribution, a turbine with a plano-convex bowl, and a turbine with a centrally convex bowl, with the hyperbolic disappearance of convexity as the radius of the rotor increases. The momentary value of wind speed, recorded at measuring points located in the plane of wind turbine blades, demonstrated an increase when compared to the base model by 35% for the wind turbine with the plano-convex bowl, for the wind speed of 5 m/s, and 31.3% and 49% for the higher approaching wind speed, for the plano-convex bowl and centrally convex bowl, respectively. The centrally convex bowl seems to be more appropriate for higher approaching wind speeds. An increase in wind turbine efficiency, described by the power coefficient, for solutions with aerodynamic bowls was observed.

Optimal Design of Horizontal Axis Wind Turbine Blades

2008 ◽  
Author(s):  
Ohad Gur ◽  
Aviv Rosen
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Design Method ◽  
Turbine Blades ◽  
Horizontal Axis ◽  
Optimization Strategy ◽  
Wind Turbine Blades ◽  
Horizontal Axis Wind Turbine ◽  
Wind Speeds ◽  
Design Variables

The optimal aerodynamic design of Horizontal Axis Wind Turbine (HAWT) is investigated. The Blade-element/Momentum model is used for the aerodynamic analysis. In the first part of the paper a simple design method is derived, where the turbine blade is optimized for operation at a specific wind speed. Results of this simple optimization are presented and discussed. Besides being optimized for operation at a specific wind speed, without considering operation at other wind speeds, the simple model is also limited in the choice of design goals (cost functions), design variables and constraints. In the second part of the paper a comprehensive design method that is based on a mixed numerical optimization strategy, is presented. This method can handle almost any combination of: design goal, design variables, and constraints. Results of this method are presented, compared with the results of the simple optimization, and discussed.

scholarly journals Experimental investigations of winglet effects on blade geometry of small horizontal axis wind turbine rotors

2021 ◽  
Author(s):  
Manoj Kumar Chaudhary ◽  
◽  
S. Prakash ◽  
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Lift Coefficient ◽  
Research Work ◽  
Operating Conditions ◽  
Horizontal Axis ◽  
Power Coefficient ◽  
Experimental Investigations ◽  
Horizontal Axis Wind Turbine ◽  
Blade Geometry

In this research work, the investigation and optimization of small horizontal axis wind turbine blade at low wind speed is pursued. The experimental blades were developed using the 3D printing additive manufacturing technique. The airfoils E210, NACA2412, S1223, SG6043, E216, NACA4415, SD7080, SD7033, S1210 and MAF were tested at the wind speed of 2-6 m/s. The airfoils and optimum blade geometry were investigated with the aid of the Xfoil software at Reynolds number of 100,000. The initial investigation range included tip speed ratios from 3 to 10, solidity from 0.0431 – 0.1181 and angle of attacks from 2o to 20o. Later on these parameters were varied in MATLAB and Xfoil software for optimization and investigation of the power coefficient, lift coefficient, drag coefficient and lift to drag ratio. The cut-in wind speed of the rotors was 2 and 2.5 m/s with the winglet-equipped blades and without winglets. It was found that the E210, SG6043, E216 NACA4415 and MAF airfoil displayed better performance than the NACA 2412, S1223, SD7080, S1210 & SD7003 for the geometry optimized for the operating conditions and manufacturing method described.

scholarly journals Airfoil optimization for small horizontal axis wind turbine

2021 ◽  
Vol 19 ◽  
pp. 505-510
Author(s):  
Cristhian Leonardo Pabón Rojas ◽  
◽  
Carlos Andrés Trujillo Suarez ◽  
Juan Carlos Serrano Rico ◽  
Elkin Gregorio Flórez Serrano ◽  
...  
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Pitch Angle ◽  
Horizontal Axis ◽  
Middle Zone ◽  
Horizontal Axis Wind Turbine ◽  
Airfoil Optimization ◽  
Low Wind Speed ◽  
Gradient Based ◽  
Blade Element

In order to take advantage of the low wind speed found in the Colombian territory, a gradient-based optimization process (GBA) of 2 airfoils is carried out, using the Xfoil software to evaluate the interactions. The shapes chosen will be destined for the root and for the middle zone of a blade for a small horizontal axis wind turbine (sHAWT). The blade will be created from the calculation of the chord and pitch angle with the blade element momentum methodology (BEM) and the SHAWT will be tested by CFD software to check its performance. As a preliminary result, a root-bound airfoil has been obtained with a higher performance than the airfoil used as a bases.

Sign in / Sign up

Export Citation Format

Share Document