The Foundation of the Sommerfeld Transformation

2002 ◽  
Vol 124 (3) ◽  
pp. 645-646 ◽  
Author(s):  
Clarence J. Maday
Keyword(s):  
Solar System ◽  
Film Thickness ◽  
Journal Bearing ◽  
Closed Orbit ◽  
True Anomaly ◽  
Central Angle ◽  
Eccentric Anomaly ◽  
One Dimensional ◽  
Analytic Singularity ◽  
The One

The analysis of the one-dimensional journal bearing leads to an interesting integral that is continuous but has an analytic singularity involving the inverse tangent at π/2. This difficulty was resolved by a clever and non-intuitive transformation attributed to Sommerfeld. In this technical brief we show that the transformation has its origin in the geometry of the ellipse and Kepler’s equation that is based upon his observations of the planets in the Solar system. The derivation of the transformation is a problem or exercise in Sommerfeld’s monograph, Mechanics. The transformation is the relation between the two angles that characterize the ellipse, the closed orbit of a body in a central inverse square force field. The angle measured about the focus is the true anomaly (angle) and the angle measured about the center is the eccentric anomaly (angle). We establish the analogy between the orbital radius in terms of the eccentric anomaly and the film thickness of the journal bearing in terms of its central angle.

The Maximum Principle Approach to the Optimum One-Dimensional Journal Bearing

1970 ◽  
Vol 92 (3) ◽  
pp. 482-487 ◽  
Author(s):  
C. J. Maday
Keyword(s):  
Maximum Principle ◽  
Film Thickness ◽  
Journal Bearing ◽  
Maximum Load ◽  
Load Direction ◽  
One Dimensional ◽  
The Maximum Principle ◽  
Minimum Film Thickness ◽  
Constant Viscosity ◽  
The One

Pontryagin’s Maximum Principle is used to determine the journal bearing which supports the maximum load for a given minimum film thickness and a specified load direction. The one-dimensional configuration which uses a constant-viscosity, incompressible lubricant is considered. Comparison shows that the optimum bearing carries a load about 13.5 percent greater than the maximum carried by the usual full-Sommerfeld bearing and about 121 percent greater than that carried by the half-Sommerfeld unit. The problem is formulated subject to the constraints of a fixed load direction and a specified minimum film thickness while the only boundary condition imposed is that the pressure must vanish at the inlet and at the outlet. The actual extent of the bearing is determined in the optimization process and it is shown that this extent is 360 deg. Further, the bearing is stepped with only two regions of different but constant film thickness.

Dynamic Analysis of Tilting-Pad Journal Bearing—Influence of Pad Deformations

1994 ◽  
Vol 116 (3) ◽  
pp. 621-627 ◽  
Author(s):  
H. Desbordes ◽  
M. Fillon ◽  
C. Chan Hew Wai ◽  
J. Frene
Keyword(s):  
Film Thickness ◽  
Pressure Field ◽  
Journal Bearing ◽  
Maximum Pressure ◽  
Tilting Pad ◽  
Minimum Film Thickness ◽  
Dimensional Finite Element ◽  
The One ◽  
Tilting Pad Journal Bearing ◽  
Tilting Pad Journal Bearings

A theoretical nonlinear analysis of tilting-pad journal bearings is presented for small and large unbalance loads under isothermal conditions. The radial displacements of internal pad surface due to pressure field are determined by a two-dimensional finite element method in order to define the actual film thickness. The influence of pad deformations on the journal orbit, on the minimum film thickness and on the maximum pressure is studied. The effects of pad displacements are to decrease the minimum film thickness and to increase the maximum pressure. The orbit amplitude is also increased by 20 percent for the large unbalance load compared to the one obtained for rigid pad.

The One-Dimensional Optimum Hydrodynamic Gas Slider Bearing

1968 ◽  
Vol 90 (1) ◽  
pp. 281-284 ◽  
Author(s):  
C. J. Maday
Keyword(s):  
Film Thickness ◽  
Load Capacity ◽  
Maximum Load ◽  
Slider Bearing ◽  
Compression Process ◽  
One Dimensional ◽  
One Step ◽  
The Difference ◽  
The One ◽  
Bearing Number

Bounded variable methods of the calculus of variations are used to determine the optimum or maximum load capacity hydrodynamic one-dimensional gas slider bearing. A lower bound is placed on the minimum film thickness in order to keep the load finite, and also to satisfy the boundary conditions. Using the Weierstrass-Erdmann corner conditions and the Weierstrass E-function it is found that the optimum gas slider bearing is stepped with a convergent leading section and a uniform thickness trailing section. The step location and the leading section film thickness depend upon the bearing number and compression process considered. It is also shown that the bearing contains one and only one step. The difference in the load capacity and maximum film pressure between the isothermal and adiabatic cases increases with increasing bearing number.

A Demonstrably Optimum One Dimensional Journal Bearing

1972 ◽  
Vol 94 (2) ◽  
pp. 188-192 ◽  
Author(s):  
S. M. Rohde
Keyword(s):  
Film Thickness ◽  
Carrying Capacity ◽  
Journal Bearing ◽  
Infinite Length ◽  
Load Carrying Capacity ◽  
One Dimensional ◽  
Load Carrying ◽  
Minimum Film Thickness ◽  
Constant Viscosity ◽  
Nonlocal Formulation

By the use of a new variational technique, the bearing profile which maximizes the load carrying capacity of an infinite length journal bearing is obtained. The lubricant is assumed to be incompressible and of constant viscosity. The flow is assumed to be laminar and the optimization is based upon a minimum film thickness. The solution obtained is a concentric step bearing with a film thickness ratio of 1.812 and a ridge to pad ratio of 0.328. It is mathematically shown by the use of the “nonlocal” formulation that this step profile does yield a maximum among all profiles sufficiently “close.”

Structure of the Bloch wall in multilayers

2005 ◽  
Vol 461 (2058) ◽  
pp. 1911-1926 ◽  
Author(s):  
Carlos J García-Cervera
Keyword(s):  
Film Thickness ◽  
Magnetic Materials ◽  
Double Layer ◽  
Dimensional Reduction ◽  
Interlayer Spacing ◽  
Optimal Shape ◽  
Bloch Wall ◽  
One Dimensional ◽  
The Core ◽  
The One

We present an analysis of the structure of Bloch walls in layered magnetic materials in the context of micromagnetics. We have obtained the Γ -limit of a one-dimensional reduction of the Landau–Lifshitz energy for a double layer in several asymptotic regimes. As a result, the optimal energy, the core length and the optimal shape of the Bloch wall have been determined. The effects of the interlayer spacing and the film thickness are studied. A comparison between the structure of the Bloch and Néel walls in multilayers is carried out. We illustrate all our findings by numerically minimizing the one-dimensional energy.

Control of Ferroelectric Properties of PbZrxTi1−xO3 Thin Film for Electron Emission Device Driven by Low Voltage

1998 ◽  
Vol 541 ◽  
Author(s):  
Y. Yamagata ◽  
M. Yamazato ◽  
T. Ikegami ◽  
K. Ebihara ◽  
J. Narayan ◽  
...  
Keyword(s):  
Electric Field ◽  
Film Thickness ◽  
Ferroelectric Phase ◽  
Low Voltage ◽  
Ferroelectric Properties ◽  
Domain Growth ◽  
One Dimensional ◽  
Pzt Films ◽  
The One ◽  
Coercive Electric Field

AbstractEpitaxial PbZr0.52TiO0.48O3/YBa2Cu3O7−x heterostructures on Nd:YAlO3 and MgO substrates were fabricated by KrF pulsed laser deposition. The coercive electric field of the PZT films increased with decrease of the film thickness from 1.2 μm to 0.04 μm, while the magnitude of spontaneous polarization was almost constant in this thickness range. It was found that the dependence of the film thickness d on the coercive electric field Ec was Ecæ d−2/3. This results from that the PZT/YBCO heterostructure has the one dimensional ferroelectric domain growth without non-ferroelectric phase. The polarization of AuIPZT/YBCO/(MgO or YAlO) capacitors can be changed by the applied voltage below 5 V.

A Variational Principle Applied to the Plane Slider Bearing

1965 ◽  
Vol 87 (4) ◽  
pp. 1081-1082
Author(s):  
Clarence J. Maday
Keyword(s):  
Variational Principle ◽  
Film Thickness ◽  
Power Loss ◽  
Minimum Principle ◽  
Slider Bearing ◽  
One Dimensional ◽  
Dimensional Plane ◽  
Minimum Film Thickness ◽  
The One ◽  
Made In

A minimum principle from hydrodynamics is applied to the one-dimensional plane slider bearing which is provided with a self-seeking pivot mechanism. An analysis was made in which a certain integral was minimized subject to the constraint that the load, speed, and viscosity were held fixed. This analysis showed that this corresponded exactly to that combination of minimum film thickness and inclination which would minimize the power loss subject to the above-mentioned constraint. It was also found that, in order to satisfy the minimum principle, there exists a definite numerical ratio between the slider inclination and the nondimensional minimum film thickness. This, in turn, fixed the pivot location relative to the length of the slider.

The Optimum Rayleigh Bearing in Terms of Load Capacity or Friction for Non-Newtonian Lubricants

1985 ◽  
Vol 107 (1) ◽  
pp. 59-67 ◽  
Author(s):  
P. Bourgin ◽  
B. Gay
Keyword(s):  
Film Thickness ◽  
Load Capacity ◽  
Maximum Load ◽  
Slider Bearing ◽  
Generalized Newtonian Fluid ◽  
Newtonian Viscosity ◽  
One Dimensional ◽  
Minimum Film Thickness ◽  
The One ◽  
Numerical Program

Pontryagin’s Maximum Principle is used to show that the configuration of the one-dimensional slider bearing which carries the maximum load for a specified minimum film thickness, is a modified Rayleigh bearing. The lubricant may be any Generalized Newtonian Fluid. Having selected two optimization criteria (1: maximum load capacity for a given minimum film thickness—2: minimum friction force for a specified load), a numerical program allows one to determine the optimal step bearing associated with the lubricant non-Newtonian viscosity. Several examples are worked out, showing that significant gains are expected, in comparison with the results obtained for the classical (Newtonian) Rayleigh bearing.

Exploring the Multidimensional Facets of Authoritarianism: Authoritarian Aggression and Social Dominance Orientation

2008 ◽  
Vol 67 (1) ◽  
pp. 51-60 ◽  
Author(s):  
Stefano Passini
Keyword(s):  
Social Dominance ◽  
Factor Model ◽  
Three Dimensional ◽  
Social Dominance Orientation ◽  
Model Fit ◽  
Regression Analyses ◽  
One Dimensional ◽  
Confirmatory Factor ◽  
The One ◽  
Better Than

The relation between authoritarianism and social dominance orientation was analyzed, with authoritarianism measured using a three-dimensional scale. The implicit multidimensional structure (authoritarian submission, conventionalism, authoritarian aggression) of Altemeyer’s (1981, 1988) conceptualization of authoritarianism is inconsistent with its one-dimensional methodological operationalization. The dimensionality of authoritarianism was investigated using confirmatory factor analysis in a sample of 713 university students. As hypothesized, the three-factor model fit the data significantly better than the one-factor model. Regression analyses revealed that only authoritarian aggression was related to social dominance orientation. That is, only intolerance of deviance was related to high social dominance, whereas submissiveness was not.

Sign in / Sign up

Export Citation Format

Share Document