Uncertainty Reduction in Gas Turbine Performance Diagnostics by Accounting for Humidity Effects

2002 ◽  
Vol 124 (4) ◽  
pp. 801-808 ◽  
Author(s):  
K. Mathioudakis ◽  
T. Tsalavoutas
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Ambient Conditions ◽  
Ambient Temperatures ◽  
Turbine Performance ◽  
Industrial Gas Turbines ◽  
Industrial Gas Turbine ◽  
The Impact ◽  
Performance Diagnostics ◽  
Health Parameters

The paper presents an analysis of the effect of ambient humidity on the performance of industrial gas turbines and examines the impact of humidity on methods used for engine condition assessment and fault diagnostics. First, the way of incorporating the effect of humidity into a computer model of gas turbine performance is described. The model is then used to derive parameters indicative of the “health” of a gas turbine and thus diagnose the presence of deterioration or faults. The impact of humidity magnitude on the values of these health parameters is studied and the uncertainty introduced, if humidity is not taken into account, is assessed. It is shown that the magnitude of the effect of humidity depends on ambient conditions and is more severe for higher ambient temperatures. Data from an industrial gas turbine are presented to demonstrate these effects and to show that if humidity is appropriately taken into account, the uncertainty in the estimation of health parameters is reduced.

Uncertainty Reduction in Gas Turbine Performance Diagnostics by Accounting for Humidity Effects

2001 ◽  
Author(s):  
K. Mathioudakis ◽  
A. Tsalavoutas
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Ambient Conditions ◽  
Ambient Temperatures ◽  
Turbine Performance ◽  
Industrial Gas Turbines ◽  
Industrial Gas Turbine ◽  
The Impact ◽  
Performance Diagnostics ◽  
Health Parameters

The paper presents an analysis of the effect of ambient humidity on the performance of industrial gas turbines and examines the impact of humidity on methods used for engine condition assessment and fault diagnostics. First, the way of incorporating the effect of humidity into a computer model of gas turbine performance is described. The model is then used to derive parameters indicative of the “health” of a gas turbine and thus diagnose the presence of deterioration or faults. The impact of humidity magnitude on the values of these health parameters is studied and the uncertainty introduced, if humidity is not taken into account, is assessed. It is shown that the magnitude of the effect of humidity depends on ambient conditions and is more severe for higher ambient temperatures. Data from an industrial gas turbine are presented to demonstrate these effects and to show that if humidity is appropriately taken into account, the uncertainty in the estimation of health parameters is reduced

scholarly journals Industrial Gas Turbine Performance: Compressor Fouling and On-Line Washing

2014 ◽  
Vol 136 (10) ◽  
Author(s):  
Uyioghosa Igie ◽  
Pericles Pilidis ◽  
Dimitrios Fouflias ◽  
Kenneth Ramsden ◽  
Panagiotis Laskaridis
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Engine Performance ◽  
Operating Conditions ◽  
Compressor Cascade ◽  
Compressor Blades ◽  
Turbine Performance ◽  
Industrial Gas Turbines ◽  
On Line ◽  
The Impact

Industrial gas turbines are susceptible to compressor fouling, which is the deposition and accretion of airborne particles or contaminants on the compressor blades. This paper demonstrates the blade aerodynamic effects of fouling through experimental compressor cascade tests and the accompanied engine performance degradation using turbomatch, an in-house gas turbine performance software. Similarly, on-line compressor washing is implemented taking into account typical operating conditions comparable with industry high pressure washing. The fouling study shows the changes in the individual stage maps of the compressor in this condition, the impact of degradation during part-load, influence of control variables, and the identification of key parameters to ascertain fouling levels. Applying demineralized water for 10 min, with a liquid-to-air ratio of 0.2%, the aerodynamic performance of the blade is shown to improve, however most of the cleaning effect occurred in the first 5 min. The most effectively washed part of the blade was the pressure side, in which most of the particles deposited during the accelerated fouling. The simulation of fouled and washed engine conditions indicates 30% recovery of the lost power due to washing.

Evaluation Program for New Industrial Gas Turbine Materials

1978 ◽  
Vol 100 (4) ◽  
pp. 704-710
Author(s):  
Ch. Just ◽  
C. J. Franklin
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Time Cost ◽  
New Materials ◽  
Evaluation Program ◽  
Evaluation Time ◽  
Industrial Gas Turbines ◽  
New Material ◽  
Industrial Gas Turbine ◽  
Phase Evaluation

The need for a thorough and systematic standard evaluation program for new materials for modern industrial gas turbines is shown by several examples and facts. A complete list of the data required by the designer of an industrial gas turbine is given, together with comments to some of the more important properties. A six-phase evaluation program is described which minimizes evaluation time, cost, and the risk of introducing a new material.

scholarly journals The Effects of Chemistry Variations in New Nickel-Based Superalloys for Industrial Gas Turbine Applications

2020 ◽  
Vol 51 (9) ◽  
pp. 4902-4921 ◽  
Author(s):  
Sabin Sulzer ◽  
Magnus Hasselqvist ◽  
Hideyuki Murakami ◽  
Paul Bagot ◽  
Michael Moody ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Experimental Characterization ◽  
Multi Scale ◽  
Aerospace Applications ◽  
Scale Modeling ◽  
Industrial Gas Turbines ◽  
Multi Scale Modeling ◽  
Superior Corrosion Resistance ◽  
Industrial Gas Turbine

Abstract Industrial gas turbines (IGT) require novel single-crystal superalloys with demonstrably superior corrosion resistance to those used for aerospace applications and thus higher Cr contents. Multi-scale modeling approaches are aiding in the design of new alloy grades; however, the CALPHAD databases on which these rely remain unproven in this composition regime. A set of trial nickel-based superalloys for IGT blades is investigated, with carefully designed chemistries which isolate the influence of individual additions. Results from an extensive experimental characterization campaign are compared with CALPHAD predictions. Insights gained from this study are used to derive guidelines for optimized gas turbine alloy design and to gauge the reliability of the CALPHAD databases.

The Impact of Atmospheric Conditions on Gas Turbine Performance

1990 ◽  
Vol 112 (4) ◽  
pp. 590-596 ◽  
Author(s):  
A. A. El Hadik
Keyword(s):  
Relative Humidity ◽  
Ambient Temperature ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Arabian Gulf ◽  
Inlet Temperature ◽  
Atmospheric Conditions ◽  
Design Factor ◽  
Turbine Performance ◽  
The Impact

In a hot summer climate, as in Kuwait and other Arabian Gulf countries, the performance of a gas turbine deteriorates drastically during the high-temperature hours (up to 60°C in Kuwait). Power demand is the highest at these times. This necessitates an increase in installed gas turbine capacities to balance this deterioration. Gas turbines users are becoming aware of this problem as they depend more on gas turbines to satisfy their power needs and process heat for desalination due to the recent technical and economical development of gas turbines. This paper is devoted to studying the impact of atmospheric conditions, such as ambient temperature, pressure, and relative humidity on gas turbine performance. The reason for considering air pressures different from standard atmospheric pressure at the compressor inlet is the variation of this pressure with altitude. The results of this study can be generalized to include the cases of flights at high altitudes. A fully interactive computer program based on the derived governing equations is developed. The effects of typical variations of atmospheric conditions on power output and efficiency are considered. These include ambient temperature (range from −20 to 60°C), altitude (range from zero to 2000 m above sea level), and relative humidity (range from zero to 100 percent). The thermal efficiency and specific net work of a gas turbine were calculated at different values of maximum turbine inlet temperature (TIT) and variable environmental conditions. The value of TIT is a design factor that depends on the material specifications and the fuel/air ratio. Typical operating values of TIT in modern gas turbines were chosen for this study: 1000, 1200, 1400, and 1600 K. Both partial and full loads were considered in the analysis. Finally the calculated results were compared with actual gas turbine data supplied by manufacturers.

Performance Deterioration in Industrial Gas Turbines

1992 ◽  
Vol 114 (2) ◽  
pp. 161-168 ◽  
Author(s):  
I. S. Diakunchak
Keyword(s):  
Gas Turbine ◽  
Service Time ◽  
Gas Turbines ◽  
Engine Performance ◽  
Turbine Engine ◽  
Factors Affecting ◽  
Preventative Measures ◽  
Industrial Gas Turbines ◽  
Performance Deterioration ◽  
Industrial Gas Turbine

This paper describes the most important factors affecting the industrial gas turbine engine performance deterioration with service time and provides some approximate data on the prediction of the rate of deterioration. Recommendations are made on how to detect and monitor the performance deterioration. Preventative measures, which can be taken to avoid or retard the performance deterioration, are described in some detail.

The Two-Shaft Industrial Gas Turbine Goes to Sea — Again

1971 ◽  
Author(s):  
Arne Loft
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
State Control ◽  
Flexible Control ◽  
Second Stage ◽  
Sequential Systems ◽  
Industrial Gas Turbines ◽  
Heavy Duty Gas Turbine ◽  
Basic Characteristics ◽  
Industrial Gas Turbine

This paper gives a brief summary of the experience of the first industrial gas turbine ship, the John Sergeant, then enumerates the basic characteristics of the heavy duty gas turbine and the philosophy employed in the design. The unique features of the second-stage variable area turbine nozzle, its effects on performance, and particularly the flexible control it affords in conjunction with the controllable and reversible pitch propeller, are discussed. The philosophy of design of the solid state control, protection and sequential systems are outlined, as are the experiences to date with a number of industrial gas turbines of the two-shaft, off-shore and heavy fuel varieties. It concludes by discussing some of the considerations for burning residual fuel and boil-off from liquefied natural gas.

Turbine Tip Clearance Measurement System Evaluation on an Industrial Gas Turbine

1997 ◽  
Author(s):  
S. J. Gill ◽  
M. D. Ingallinera ◽  
A. G. Sheard
Keyword(s):  
Gas Turbine ◽  
Measurement System ◽  
Gas Turbines ◽  
Turbine Blades ◽  
Tip Clearance ◽  
Real Time Measurement ◽  
Gap Measurement ◽  
Industrial Gas Turbines ◽  
Blade Tip ◽  
Industrial Gas Turbine

The continuing development of industrial gas turbines is resulting in machines of increasing power and efficiency. The need to continue this trend is focusing attention on minimizing all loss mechanisms within the machine, including those associated with turbine blade tip clearance. In order to study tip clearance in the turbine, real time measurement is required of clearance between turbine blades and the casing in which they run. This measurement is not routinely performed, due to the harsh nature of the turbine environment. On those occasions when turbine tip clearance is measured, it is typically in development vehicles, often using cooled probes that are somewhat unsuitable for use in production gas turbines. In this paper a program of work is reported that was undertaken with the purpose of identifying a promising turbine tip clearance measurement system that used the capacitive gap measurement technique. Issues surrounding the application of three systems to the turbine section of a GE MS6001FA gas turbine are identified and reported. Performance of the three evaluated systems is analyzed.

Performance Deterioration in Industrial Gas Turbines

1991 ◽  
Author(s):  
Ihor S. Diakunchak
Keyword(s):  
Gas Turbine ◽  
Service Time ◽  
Gas Turbines ◽  
Engine Performance ◽  
Turbine Engine ◽  
Factors Affecting ◽  
Preventative Measures ◽  
Industrial Gas Turbines ◽  
Performance Deterioration ◽  
Industrial Gas Turbine

This paper describes the most important factors affecting the industrial gas turbine engine performance deterioration with service time and provides some approximate data on the prediction of the rate of deterioration. Recommendations are made on how to detect and monitor the performance deterioration. Preventative measures, which can be taken to avoid or retard the performance deterioration, are described in some detail.

Study of Using Exhaust Gas Recirculation on a Gas Turbine for Carbon Capture

2020 ◽  
Author(s):  
Dan Burnes ◽  
Priyank Saxena ◽  
Paul Dunn
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Carbon Capture ◽  
Hydrocarbon Fuel ◽  
Exhaust Gas Recirculation ◽  
Exhaust Gas ◽  
Hybrid Solutions ◽  
Industrial Gas Turbines ◽  
Industrial Gas Turbine ◽  
Gas Recirculation

Abstract The growing call of minimizing carbon dioxide and other greenhouse gases emitting from energy and transportation products will spur innovation to meet new stringent requirements while striving to preserve significant investments in the current infrastructure. This paper presents quantitative analysis of exhaust gas recirculation (EGR) on industrial gas turbines to enable carbon sequestration venturing towards emission free operation. This study will show the effect of using EGR on gas turbine performance and operation, combustion characteristics, and demonstrate potential hybrid solutions with detailed constituent accounting. Both single shaft and two shaft gas turbines for power generation and mechanically driven equipment are considered for application of this technology. One key element is assessing the combustion system operating at reduced O2 levels within the industrial gas turbine. With the gas turbine behavior operating with EGR defined at a reasonable operating state, a parametric study shows rates of CO2 sequestration along with quantifying supplemental O2 required at the inlet, if needed, to sustain combustion. With rates of capture known, a further exploration is examined reviewing potential utilities, monetizing these sequestered constituents. Ultimately, the objective is to preview a potential future of operating industrial gas turbines in a non-emissive and in some cases carbon negative manner while still using hydrocarbon fuel.

Sign in / Sign up

Export Citation Format

Share Document